Jump to content

Adjust or replace torsion bar in 1999 K1500?

lunytnz
 Share

Recommended Posts

lunytnz Enthusiast

lunytnz

Posted
Posted

My 1999 4-door Yukon 4x4 is bottoming out the front suspension on big dips in the road.  I replaced the shocks, but that wasn't enough to remedy the problem.

Since this model doesn't have springs, I'm wondering if I can adjust the torsion bars in the 1999 or if I need to replace them?  If I adjust the torsion bars, will it affect wheel alignment?

newdude Senior Enthusiast

newdude

Posted
Posted (edited)
55 minutes ago, lunytnz said:

My 1999 4-door Yukon 4x4 is bottoming out the front suspension on big dips in the road.  I replaced the shocks, but that wasn't enough to remedy the problem.

Since this model doesn't have springs, I'm wondering if I can adjust the torsion bars in the 1999 or if I need to replace them?  If I adjust the torsion bars, will it affect wheel alignment?

 

 

Are your jounce bumpers still there?  If they are, are they worn out or missing?  The jounce bumper is an integral part of the torsion bar IFS on these GMs.  

 

If they are original or the rubber is missing, GM discontinued the standard bumper which fit 1995-2000 Tahoe and was the same bumper 1999-2010 HD pickups.  Because of this though, you can use the 07-10 Z71 HD bumpers, p/n 15835667.  

 

We had a tech get burned by that on an 03 1 ton dump.  Front end was super bouncy, tech sold shocks, didn't fix it.  The jounce bumpers weren't even in the frame anymore, just the stud and nut that's molded into the bumper was left.  New bumpers and it drove great.  

Edited by newdude
  • Like 1
lunytnz Enthusiast

lunytnz

Posted
  • Author
Posted

Thanks for calling my attention to the jounce bumper!  I have the FSM, but I haven't been able to locate the bumper to make sure I'm looking at the right part. As far as I know, the bumper is original (I've owned it for over 20 years).

 

Here's a drawing from the service manual, as well as a picture of the front suspension in my rig. 

 

Can you point out the jounce bumper?  TIA!

 

20241025_162858.jpg

20241025_162029.jpg

newdude Senior Enthusiast

newdude

Posted
Posted
3 hours ago, lunytnz said:

Thanks for calling my attention to the jounce bumper!  I have the FSM, but I haven't been able to locate the bumper to make sure I'm looking at the right part. As far as I know, the bumper is original (I've owned it for over 20 years).

 

Here's a drawing from the service manual, as well as a picture of the front suspension in my rig. 

 

Can you point out the jounce bumper?  TIA!

 

20241025_162858.jpg

20241025_162029.jpg

 

 

 

It would be above the lower control arm, rear "A" of the lower arm mounted on the frame.  

 

 

 

jounce.thumb.png.b7131ad106c23fc9701dbddff66c6fcd.png

lunytnz Enthusiast

lunytnz

Posted
  • Author
Posted (edited)

Thx for the picture. Before I saw it, I took this picture from the other side. Is this where the bumper should be?

 

I presume the torsion bar is adjustable. Is that something I should look into, as well?

20241027_093852.thumb.jpg.667689d556685c8fcac377e9cf00500c.jpg

Edited by lunytnz
asilverblazer Senior Enthusiast

asilverblazer

Posted
Posted

Yep, there should be a bumper there.

 

Torsion bars aren't typically 'adjusted'. But the years and mileage on the rig may have caused them to settle/wear some. There is a specification for adjustment - 'z-height'. It's not a very intuitive measurement to take. The easiest method, is to measure from the bottom of the lower control arm bolt to the ground and record the measurement. Measure from the rear lower control arm mounting bolt to the ground and record the measurement. The difference between these two is the 'z-height'. Refer to your factory service manual and confirm my measurement points because I might be remembering them wrong. It should also specify the measurement.

 

Torsion bar adjustment will require an alignment afterwards. 

  • 10 months later...
lunytnz Enthusiast

lunytnz

Posted
  • Author
Posted

Thanks, again, for pointing out the missing rubber bumper and helping to clarify where it was supposed to be!

 

I was able to find replacement parts at Napa (I was surprised that they are about the size of your fist).  It was difficult to get the nut off the old, rusty bolt, because the OE bumper was COMPLETELY disintegrated, but I eventually prevailed.

 

I put it to the test on a drive on a Forest Service road with big dips in the road and no problems with bottoming out the front suspension anymore.

 

Here's a picture of the front suspension with the new rubber bumper installed.

 

Cheers!

 

Yukon Suspension Bumper - replaced - Mar 2025.jpg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,774
    Total Members
    8,960
    Most Online
    lanaderay
    Newest Member
    lanaderay
    Joined

  • Who's Online   4 Members, 0 Anonymous, 1,532 Guests (See full list)

  • Latest Articles

  • Posts

    • lanaderay
      5 Best Slide Down Gameplay Tips! 

      By lanaderay · Posted

      Are you playing Slide Down endlessly but your score is still low? Are you constantly crashing into obstacles as the game speed increases? Don't worry, this article will share 5 invaluable tips to help you master the race and impress your friends. Golden Rules 1. Look one step further. The mistake of 90% of new players is only staring at their character. The secret of experts is to look towards the top of the screen (where the slide is about to appear). This gives your brain an extra 0.5 - 1 second to process the situation and determine the direction of movement before the obstacle approaches. 2. Use gentle movements; don't swipe too hard. Slide Down is very sensitive. Moving your finger too forcefully or with excessive amplitude will cause your character to be thrown off course or crash into a wall. Practise moving your finger with small, decisive, and precise movements. 3. Don't be greedy for gold in dangerous locations. Gold coins are tempting for buying skins, but life is more important. If you see a gold coin right on the edge of a cliff or next to a spike trap, ignore it. Our goal is a High Score, and your score only increases if you survive. 4. Make the most of Power-ups. During the slide, you'll encounter items like Magnets (attract gold) or Shields (temporary invincibility). Never miss them! Especially the Shield, it's your "get out of jail free card" to help you get through those deadly fast sections. 5. Stay calm when speed peaks. When your score exceeds 500 or 1000, the game speed will be very fast. At this point, don't try to think logically; let your natural reflexes work. Take deep breaths and don't panic. Apply these 5 tips to your next game, and your leaderboard will surely improve dramatically. Good luck climbing the Slide Down leaderboard!
    • lingyuair
      Why I Recommend a Desiccant Air Dryer for Cleaner, Drier Compressed Air

      By lingyuair · Posted

      If you use compressed air regularly, one problem you cannot ignore is moisture. Water in the air line can cause rust, unstable air pressure, poor tool performance, and even damage to sensitive equipment. That is why I highly recommend using a desiccant air dryer. A desiccant air dryer is designed to remove moisture from compressed air by using drying materials such as activated alumina or molecular sieve. Compared with basic water separators, it can achieve much lower dew points, making it especially useful for applications that require dry and stable air. For workshops, painting systems, pneumatic tools, CNC machines, laser cutting equipment, and industrial production lines, a desiccant air dryer can make a big difference. It helps protect equipment, improve air quality, reduce maintenance costs, and extend the service life of the whole compressed air system. Another advantage is reliability. Many desiccant air dryers are built for continuous operation and can maintain stable drying performance even in demanding environments. For users who care about long-term efficiency and equipment protection, this is a smart investment. When choosing a desiccant air dryer, I suggest paying attention to air flow capacity, working pressure, dew point performance, regeneration method, and maintenance requirements. A good model should match your compressor system and actual air consumption. Overall, if moisture is causing problems in your compressed air system, a desiccant air dryer is definitely worth considering. It is practical, efficient, and highly useful for anyone who needs clean, dry, and reliable compressed air.
    • Jsdirt
      2027 GMC Sierra: Official Discussion

      By Jsdirt · Posted

      My brand new 2007 Silverado's wax frame was rust from end to end partway through it's SECOND winter here in MA. That stuff is completely useless.    
    • Jsdirt
      2027 GMC Sierra: Official Discussion

      By Jsdirt · Posted

      I went another direction after losing a trailer tire, thanks to not being able to access air at ANY of the 5 gas stations and garages I stopped at prior, with a Toyota Tacoma onboard, 50 miles from the Canadian border. They were either out of order, access was blocked, or the hose a few feet too short and I couldn't get any closer without risking damage to someone's property.   https://postimg.cc/gallery/X5QJ55w
    • Another JR
      Remote Start Noise 2024 2500 HD Gas

      By Another JR · Posted

      I took a 12 second video on my iphone but the file is too big to upload. I will have to figure out how to extract the audio or just do another start with an audio recording. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...