Jump to content

Swapped interior from LT to High Country.

lennybg
 Share

Recommended Posts

lennybg Enthusiast

lennybg

Posted
Posted

Just finished swapping out my LT cloth interior with the jump seat console to the Full console and Leather seats from a High Country.

Extremely easy to do. Hardest part was the rear seat back. The entire process took about 2.5 hrs. I already had a power drivers seat and was able to just plug it right in with no issues.

Since my pax side seat was manual I had to order the wiring harness from HarnessDR which should be here today. So right now im riding around ghetto style with leather drivers and rear seats and a cloth pax seat.😄

The console was very easy as well. Just plus and play on that too. The only things that dont work are the USB ports on the inside of the console which is a known issue and then the wireless charging. There was a wire at the front of the console that I did not have a connection for. If you are swapping out the jumpseat console, you will need a new trim piece if you don't already have it. GM Part# 85110488.

If you're on the fence about doing this, don't be.

Im all in for $700. That included both front Seats,Rear seat, and the Center console.

  • Like 1
lennybg Enthusiast

lennybg

Posted
  • Author
Posted
15 minutes ago, N715DP said:

I second the request for pics... where did you acquire the seats?

Off FB Market place. The seller wrecked his HIgh Country and was selling off parts.

There are actually quite a few in the DFW area that were the same price(`$700-800) Most seemed to be from Denali's but I went with the high country simply because it was closest to me. They are the same seats and console just different wording on the headrest :)

 

lennybg Enthusiast

lennybg

Posted
  • Author
Posted
17 hours ago, Kevin0311 said:

Don't the Denali's have massage seats where the high country do not?

That would be nice...

These are just heated and not cooled, and they were alot closer than the denali seats to my location.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,860
    Total Members
    8,960
    Most Online
    HWN808
    Newest Member
    HWN808
    Joined

  • Who's Online   5 Members, 1 Anonymous, 1,063 Guests (See full list)

  • Latest Articles

  • Posts

    • txab
      Gas Prices

      By txab · Posted

      $3.59  
    • needafix
      2019+ Brake failure, it's complicated

      By needafix · Posted

      I'm not sure if this should be a new topic, let me know if it's out of place. This my first post. Thanks 85077522 - AC Delco GM Genuine Parts Brake Master Cylinders. Anyone else had to replace this brake master cylinder yet. I didn't do any brake work, it looks like new parts and I've had the truck for about 4k miles, 119k total miles.  When it started to throw codes I did the calibrations with a bidirectional scanner and got the codes to clear but they came back so I did the routine; base bleed, automated bleed and final base bleed. All that with Bosch ES16-32N fluid (please look it up). That seemed to fix it but 100ish miles later it failed again so I ran the same process but with a pressure bleeder this time and got the same results, fixed for 100ish miles. The original fluid looked bad and I thought I got most of it out, it could've been the wrong fluid. The codes; P25A2, C05B0-00, C2A1B. I can get them to clear but not for long. The C05B0 indicates a leak in the front circuit (which is bone dry) so I'm thinking of doing the bleed process on that front again today and I don't know if that's taboo to just do the front but at this point it seems like it's worth the try anyway. The new master cylinder/module unit is supposed to get here today. But now I'm pretty much convinced this install is over my head. I've called several shops and some mobile guys that I know but this thing is like radio active material, scary wise. I did get 2 local shops say they should be able to do it, one says he has the SPS2 programing capability. And with the battery disconnected is there supposed to be pedal resistance, mine is to the floor, then if I pump it I can get some resistance. I had a panic stop prior to this issue which may have contributed from what I read. And on the first attempt to bleed and hydraulic test the scanner listed things to look for and one was any gaps between the pad and rotors which I did notice on the RF corner and I removed the outer pad (where the gap was) cleaned it and the hardware and didn't see a gap after that but will re-check it. I read that if pushing the caliper pistons back then you're supposed to open the bleeder so as to not push fluid backwards into the abs module or it will damage it. If that's true then that's also a possibility from the previous owner having the brakes changed before I got it. I'm using an XTool ip500 scanner. Any suggestions, questions and comments welcome. 
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      Next Friday will be my 6 week point from my right knee replacement.  The surgeon says it will be fine if I choose to drive after this checkup.  I know I could drive now but best to do as my surgeon (and my wife) tell me.  Richard compared being 62 to 72.  I remember when I was in my early 60's I was experiencing slow but regular decline in my mobility.  Thanks to good medical support,  i continued to fight the speed and spread of this decline. During my 60's I worked on non-surgical methods and just when I turned 70, my orthopedic surgeon recommended joint replacements.  In a little over a year, I had one shoulder and both knees replaced.  This hasn't been a terribly fun experience, but worth the discomfort as my future mobility health trajectory has reversed.  It is a treat to now be watching my mobility. balance and confidence steadily improve!
    • Another JR
      Trailer TPS Sensor Question Rim Size

      By Another JR · Posted

      Grommets with the right cement should be perfectly fine. 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      This is going to take allot of Assembly    

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...