Jump to content

upgrading camera system

Dan Cotter
 Share

Recommended Posts

Dan Cotter New Member

Dan Cotter

Posted
Posted

I just bought a 2024 2500HD Duramax. It currently has just the backup and trailer hitch camera. Does anyone know what would be required to upgrade to the multi camera. I found find multi camera control modules really inexpensive on eBay, just not sure what else may have to change. Is it as simple as replacing the original control module (likely need to be programmed to the vehicle) and installing the desired Camera. I know of aftermarket systems but they are "clunky" to operate.

Has anyone done this?

Ry Guy Enthusiast

Ry Guy

Posted
Posted

I think the challenge you are going to face is getting a dealer to agree to program modules that are not part of your original build sheet. I don't think they are allowed to, and the most likely won't (or can't) program used modules.

Randal Scott Enthusiast

Randal Scott

Posted
Posted

Your truck may not have the wiring for the other cameras. My 2020 2500hd silverado didn't come with the bed camera. Checked with GM about adding it. The original build sheet showed that it was suppose to have it. But during the build, it got deleted and the wire harness wasn't added. Now if I want it, Etrailer has a kit goes in with the rear camera and I can switch between the two. 

Dunn Senior Enthusiast

Dunn

Posted
Posted

really want to get these options when you purchase, so much easier......kinda sucks the onedudes got deleted during the build....am sure the credit wasnt what it costs to add one now

Ry Guy Enthusiast

Ry Guy

Posted
Posted (edited)
5 hours ago, Randal Scott said:

At Etrailer it's $600 plus for the kit. 


Can you provide a link to it?

Edited by Ry Guy
Randal Scott Enthusiast

Randal Scott

Posted
Posted (edited)

 

Custom Third Brake Light Camera for 8" Factory Monitor - Night Vision

I'll try and get a better link. 

Edited by Randal Scott

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      The not as clean as one would assume theme with the new engine oil, that reminds me of comments over the years with mechanics not always being so on board with filling an oil filter, not from the center anyway due to that typically being the clean side of the filter, danger of some contaminant falling into the filter if not careful but the realization now that the oil may not be as pure as one had assumed it would surely be. Yes it would be possible to fill from the small holes but that means messing with something to prop open the anti drain back valve if the filter is so equipped and not damage that valve in the process. Me, I have hardly ever prefilled an engine oil filter however I have prefilled diesel fuel filters with a filter on a fuel bulk tank and for anyone that has messed with diesel engines with filters and units that have a limited or no way of priming them, putting on a dry filter is a bad day to say the least with those crappy systems. But anyway back to not so clean engine oil, indeed perhaps its not so bad after all that I have not made a practice of prefilling oil filters.    As Grumpy Bear commented on keeping things clean, that I really have to wonder what the typical practice is at a dealer or any other shop that changes engine oil, do they make sure to wipe or wash off the oil plug and certainly if it fell into some gunk or onto a dirty floor, or that they wiped the filter mounting flange and didn't go and use some dirty rag and end up adding dirt to the inside of the head of the filter mount. Or be careless in how they stored or handled the new filter and if they were bumping into items under the vehicle with the filter opening facing up and having dirt drop right into the filter and if so right into the threaded center that is on the clean side. The top side, did they clean away the built up gunk that may be around the filler before removing the cap or to be really careful at that point that something right close to the filler hole that was hidden under the caps flange won't fall into the engine. Or did they clean the funnel or was that just laying there covered in oil from the oil change before and dust kicked up from sweeping the floor stuck to the oil and now that will go running into the next persons engine due to just not cleaning the funnel as "they won't know anyway" attitude as that young guy is more worried about taking a break so he can go outside and smoke a joint. Just random points that came to mind when I think about what some hired personnel may do that the shop foreman has no idea of or perhaps the whole attitude of some shops may be "eh ... who cares, they will never know the difference anyway".  
    • CamGTP
      Gas Prices

      By CamGTP · Posted

      $3.69 for 87 octane.   $4.24 for Diesel in town.
    • Atlas
      OCI, not when but why?

      By Atlas · Posted

      On the subject of OLM, Gm's OLM tool may be more "informed" than others brands. I recall OLM's in mid-2000's Chrysler products literally counting down a set number of miles. That's all the OLM appeared to be.    I would actually expect GM to be able to explain the parameters that their OLM takes into account from a high level. No, I would not expect them to disclose their software coding or data analysis around their parameters.   So we're talking about two different topics, so to continue the subject on the other one, I'd be curious to know how much "standard particulate matter" in fresh oil is able to be filtered at first start by a fresh oil filter. How much particulate matter is enough to "matter"?   I.e. how much of a "lever" do we think this equates to (variability in particulate content, in fresh oils, between different makes/brands, some which filter less, and some that filter more).   We can say that more particles = more wear = shorter engine life as a logical statement and use that data with a little marketing to scare people into selecting a more refined/filtered oil. Using a similie, is this like deciding to forego two alcoholic drinks in a lifetime because we're worried about the potential impact on lifespan? Are there numbers which translate the ISO test results into a quantifiable increase in wear for a given engine/use case?
    • chris21
      Brand new to this forum. Questions about re-gearing my 26’ HD

      By chris21 · Posted

      I'm pretty sure it doesn't actually recalibrate the speedometer it just changes the wheel speed sensor inputs to the computer. The truck still thinks it has stock tires.
    • asilverblazer
      OCI, not when but why?

      By asilverblazer · Posted

      I apologize, I missed this post, at risk of going off CURRENT TOPIC.   I'm not saying it is BS, I'm questioning how much information is being held back. GM is NOT going to spell out exactly every parameter in the algorithm. Liability, intellectual property, etc.    I'm not naive enough to believe that it is as simple as revolutions, coolant temperature, miles, time; are you?    I don't do irrational either, and boiling the OLM down to four simple values that I could code in an afternoon (I'm not a coder) is irrational - unless it suits your agenda to ignore it. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...