Jump to content

2024 Silverado RST 6.2l v8 missfire

Silverado8810
 Share

Recommended Posts

Silverado8810 Enthusiast

Silverado8810

Posted
Posted (edited)

Just purchased a 2024 Silverado RST with the 6.2l v8, 17k miles. A few days ago I noticed a stutter while driving, lasted about 10-15 seconds then disappeared. Next day it did the same thing again. Later that night the stutter returned much worse, definitely a missfire, then check engine light started flashing and service stability system light came on. Attempted to pull over and before I could come to a stop the lights went off and the missfire disappeared. Drove it home about 20 miles and it ran fine the whole way. Hooked my reader up and it showed 34 active codes the first being p2255 O2 sensor negative current. Next two codes read manufacturer specific blah blah blah, scrolled to the fourth code and all codes dissapeared from the reader. Re-scanned and no codes (active, stored, or pending). Tried another scan tool and that also read no codes. Driven it the last 2 days to work and back with no issues. Today I had a coworker try his 2 code readers for a sanity check and they also show 0 codes. Being intermittent definitely seems like an electronic issue to me but outside that I’m lost. I talked to the dealership and have an appointment scheduled for next week but without codes I don’t have much faith that they will be able to locate the issue. Any insight is appreciated.

Edited by Silverado8810
Bikerjon Enthusiast

Bikerjon

Posted
Posted
1 hour ago, Silverado8810 said:

Just purchased a 2024 Silverado RST with the 6.2l v8, 17k miles. A few days ago I noticed a stutter while driving, lasted about 10-15 seconds then disappeared. Next day it did the same thing again. Later that night the stutter returned much worse, definitely a missfire, then check engine light started flashing and service stability system light came on. Attempted to pull over and before I could come to a stop the lights went off and the missfire disappeared. Drove it home about 20 miles and it ran fine the whole way. Hooked my reader up and it showed 34 active codes the first being p2255 O2 sensor negative current. Next two codes read manufacturer specific blah blah blah, scrolled to the fourth code and all codes dissapeared from the reader. Re-scanned and no codes (active, stored, or pending). Tried another scan tool and that also read no codes. Driven it the last 2 days to work and back with no issues. Today I had a coworker try his 2 code readers for a sanity check and they also show 0 codes. Being intermittent definitely seems like an electronic issue to me but outside that I’m lost. I talked to the dealership and have an appointment scheduled for next week but without codes I don’t have much faith that they will be able to locate the issue. Any insight is appreciated.

Just a guess. Check the ground strap in the engine compartment. Its on the passenger side. It connects the firewall to the frame. Lots of issues have been caused by a poor connection there.

GMCustomerService Senior Enthusiast

GMCustomerService

Posted
Posted
3 hours ago, Silverado8810 said:

Just purchased a 2024 Silverado RST with the 6.2l v8, 17k miles. A few days ago I noticed a stutter while driving, lasted about 10-15 seconds then disappeared. Next day it did the same thing again. Later that night the stutter returned much worse, definitely a missfire, then check engine light started flashing and service stability system light came on. Attempted to pull over and before I could come to a stop the lights went off and the missfire disappeared. Drove it home about 20 miles and it ran fine the whole way. Hooked my reader up and it showed 34 active codes the first being p2255 O2 sensor negative current. Next two codes read manufacturer specific blah blah blah, scrolled to the fourth code and all codes dissapeared from the reader. Re-scanned and no codes (active, stored, or pending). Tried another scan tool and that also read no codes. Driven it the last 2 days to work and back with no issues. Today I had a coworker try his 2 code readers for a sanity check and they also show 0 codes. Being intermittent definitely seems like an electronic issue to me but outside that I’m lost. I talked to the dealership and have an appointment scheduled for next week but without codes I don’t have much faith that they will be able to locate the issue. Any insight is appreciated.

We understand this is far from the ownership experience you would hope for. We are relieved to hear you are working with your GM dealership to address this stutter, though our team would like the opportunity to act as an extra layer of assistance. When you have a moment, please send us an email at [email protected] so we can help. By sending us a message, you consent to the information you provide being monitored and recorded by GM or those acting on GM’s behalf, subject to the GM Privacy Statement: https://www.gm.com/privacy-statement.

Silverado8810 Enthusiast

Silverado8810

Posted
  • Author
Posted
1 hour ago, Bikerjon said:

Just a guess. Check the ground strap in the engine compartment. Its on the passenger side. It connects the firewall to the frame. Lots of issues have been caused by a poor connection there.

I will check on this tomorrow. Thanks for the insight

Silverado8810 Enthusiast

Silverado8810

Posted
  • Author
Posted
On 4/23/2025 at 8:02 PM, GMCustomerService said:

We understand this is far from the ownership experience you would hope for. We are relieved to hear you are working with your GM dealership to address this stutter, though our team would like the opportunity to act as an extra layer of assistance. When you have a moment, please send us an email at [email protected] so we can help. By sending us a message, you consent to the information you provide being monitored and recorded by GM or those acting on GM’s behalf, subject to the GM Privacy Statement: https://www.gm.com/privacy-statement.

No response

Silverado8810 Enthusiast

Silverado8810

Posted
  • Author
Posted

Update: Had the service with the dealership and as I feared, they couldn’t find anything wrong or replicate the problem. They did find a P02F5 code which is a fault in the fuel system and a P0300 misfire code but those were not currently active and just in the history so they said they could do nothing unless the CEL returned. Also, with the new recall on the 6.2, they could not address that either as it is still showing pending. 

  • Sad 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Another JR
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By Another JR · Posted

      Have considered installing a DC to DC charger in your camper to replace your isolator?  
    • newdude
      Gas fill door

      By newdude · Posted

      Common failure.  You need to replace the fuel door housing.   The painted cover transfers over to the new housing.  To remove the old one there is 4 spots where you poke the plastic to release it.  
    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      I have an observation and a question... 1) I watch the voltage closely because I have had to dial in the cut-in/cut-out voltages of the battery separator to my camper.  The "smart" charging drives me nuts.  Anyway, I noticed that when coasting for a while, and especially if lightly using the brakes (though not necessary), the voltage goes up from mid/high-13 volts to mid/high-14 volts.  Then it drops back down after stopping or going again.  Consistently!   The only explanation I can come up with is REGENERATIVE BRAKING!  Well, maybe that's a little bit of an exaggeration, but it's certainly free extra battery charging.   2) Driving on mountain roads I will use L and vary the max gear.  Things straighten out and I end up in L10.  Sometimes I leave it there for a while.  Is there any difference between L10 and D?   

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...