Jump to content

Possible lifter tick after DOD delete

B14Sierra

By B14Sierra
in Engines & Drivetrain

 Share

Recommended Posts

B14Sierra Enthusiast

B14Sierra

Posted
Posted

I'm starting to lose my mind with this truck. I just recently did a DOD delete on my 2014 6.2. Originally had a misfire on cylinder 5 and traced it down to bad lifter. I installed the BTR kit with a stage 1 cam. I also went ahead and put new complete heads on wirh new injectors. The truck runs great on the road but at idle you can tell a slight uneven shake and slight ticking sound. Can't hear it in the cab. Can't tell where it's coming from. It seems louder on the drivers side but you can also hear something on the passenger side. i can't tell if it'san actual lifter tick or injector/high pressure fuel pump tick. I did not change the oil pump and I'm hearing that I should have. I was told a new one could fix the tick but I don't know. At cold start pressure is at 40. Once hot, driving it's at about 38 and at idle it's about 32.

 

I'm not getting any misfire codes but I have gotten a P2097 code. Bank 1 to rich on the downstream O2. I have a feeling my drivets side Cat is going bad from when the cylinder 5 lifter went and was dumping fuel on that side. So yeah, I might have a couple of things going on but that tick has got me worried. I don't want to rip this thing apart again. I don't know what I should do at this point.

B14Sierra Enthusiast

B14Sierra

Posted
  • Author
Posted

Update. I started chasing down my symptoms. Started first with pulling valve covers and looked at everything. Everything looked good and couldn't hear or feel anything different. Then a compression test. 240 psi or really close on each cylinder. I was worried I was a tooth off of timing. Not bad for an engine with 173,000. Granted I did put new heads on. I sprayed water around the injector area to see if I could hear a change. Nothing. I hooked up my new hp tuner which I should have done in the first place but I don't really know what I'm looking at just yet but am learning. I noticed the fuel trims were way off so that told me I have to have either a bad injector or exhaust leak. New injectors, so I did the shop vac on blower and in the tail pipe. Sprayed soapy water and found the exhaust flange on the drivers side was leaking. I didn't think it would be that considereding I pulled the heads and left the manifolds attached. I did have the transmission replaced not long ago. They must have not seated them properly but I guess I didn't notice. I put in new gaskets on both sides. Which by the way isn't a bad job but I had a hard time getting them to seal right. Took two attempts. Reset the fuel trims and the ticking is gone, engine runs smooth and acceleration has improved. Got to feel the real difference with that stage 1 cam. It's not that big of a difference but it does add a little more. It feels like how the truck should have been from the factory.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • bwiese
      seat base height *lowering* (base 40/20/40 seat, 2026 1500 WT std cab)

      By bwiese · Posted

      Folks, Have a great new 2026 WT  (std cab, 2.7/4WD) w/base 40/20/40 mech adj bench "fake buckets"  (with lower and upper center console) heavy vinyl seats.  Overall the seats are very comfortable and the vinyl is heavy and appears less likely to 'split out'. Am very tall (6'5")  + a bad back/osteporosis/former hyperparathyroidism so ease/range of movement is a bit restricted.  The truck rides a bit high and I use a nerf step bar w/my left foot to step in, then I put right foot/leg in, drag my butt in  & get seated.  Worked fine in my 2018 RAM quadCab. But I end up dragging my butt over the left raised sidecushsion area of vinyl seat, and due to texture there's fair amount of traction on slide inward.  (ArmorAll didn't improve.) If the seat were even ~1/2" - 3/4" lower it'd be helpful, but base seats just have the forward/backward underseat bail and the side lever for tilt which really doesn't affect seat height.   I really don't want to 'de-puff' the left side sidecushion forming the  fake 'bucket'. I know one company sells 'seat elevator blocks':  but is there a simple way of lowering the height of the driver seat instead?   Thanks Bill W San Jose  
    • bwiese
      on-wheel cellphone control: 2026 1500 WT (2.7L 4WD std cab)

      By bwiese · Posted

      I have a basic 2026 1500 WT  (2.7L/4WD reg cab shorttbed). Comfy, generally happy with electronics/radio - but is there a way I can add switches to steering wheel right-side position (curr. empty) so I can adjust volume, push phone button to voice dial, etc? Bill W San Jose  
    • Tyler Gibbs
      Travel Trailer 2024 2500 HD 6.6 Gas Engine ?

      By Tyler Gibbs · Posted

      The curb weight on a 1 ton crew cab long bed is around 7k lbs.  Now, I don't know where you went to school but 9k is not more than 2x 7k lbs. More than 2x 7k lbs would be 14k+.   With that said, obviously yes you're going to feel a 9k lb trailer when slowing down.  I already said, when accelerating.  When changing lanes?  No.  But if you look at the context of what was quoted, the original person said, "after a mile or two..." which means that would be after the accelerating portion and you're driving a generally steady pace.  Please do learn to read and comprehend.
    • sFrank
      2026 Silverado Range AFM DFM ECU loaction

      By sFrank · Posted

      So I purchased the Range unit for my 2026 and I am seeing different locations suggested for the ECM . Can anyone confirm wither under hood, left side or right side or behind the wheelwell?
    • No F-bdy Bs
      Dave's Auto (custom engine builder) tear down of L8T

      By No F-bdy Bs · Posted

      Like I've said before. Di and Carbon buildup is not that big of a concern. Engine had minimal buildup, and that engine was obviously not super well maintained. Do regular oil changes, and you're gtg as long as the rest of the truck lasts. Also, the High Pressure FP that people ****** about, but can't tell you why.  Now, I wish they'd trash the variable oil pump. No real world issues with them, but I'll gladly eat whatever miniscule MPG it's saving me in favor of more oil at all RPMs.    Curious to see his assessment of the 7.3 compared to the 6.6. I expect he'll praise the port inj, but from a structural standpoint, the 6.6 is as robust as any engine out there.    Not to take away from the 7.3. I feel it's equally as good as the 6.6.     As to heat on the rear cyls, I'd have to see numerous examples before I'd say it's an issue. Especially not knowing the history of that engine. For all is known, they could have blown a rad hose, and ran it hot, and the 2 rear cyls may be the first to get hot in a low coolant situation, but not be an issue aside from that. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...