Reset CLN message on Tape Deck

By rwarner
May 26, 2004 in Audio, Electronics & Software

Recommended Posts

rwarner

Posted May 26, 2004

Hi,

I received the message CLN on my stareo display from my tape deck I have done the steps in the owners manual to clean the unit but with no luck. I can not get the reset complete by holding in the eject button. My stareo is a Delco Electronis CD w/cassette unit in a 2001 Silverado Z71 4x4. Any help or ideas would be great.

Thank You

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

Recently Browsing 0 members
- No registered users viewing this page.
Forum Statistics

250.5k
Total Topics

2.7m
Total Posts
Member Statistics

342,892
Total Members

8,960
Most Online

Newest Member
EllDMc
Joined 7 hours ago
Who's Online 1 Member, 0 Anonymous, 649 Guests (See full list)
- davester

Latest Articles
- GM Brags About Not Discounting Your Next Truck
  Monday at 09:05 PM
- GM Adds Super Cruise to 160,000 More Pickups in 2027
  Monday at 06:16 PM
- GM Investigating HUD Settings Glitch on Nine SUV Models
  July 24
- The Real Reason GM’s New V8 Truck Engines Ditched 0W-20
  July 24
Posts
- 07 yukon xl 6.2 stalls at hot idle and wont restart
  
  By davester · Posted 59 minutes ago
  
  computer pulses the injectors by connecting them to ground (at least on the trucks), so they get constant power...
- 07 yukon xl 6.2 stalls at hot idle and wont restart
  
  By Jsdirt · Posted 2 hours ago
  
  PCM powers and grounds - EVERY one of them has to be good. Since PCM replacement didn't fix it, then all of these need to be good, AND the ground from the computer to the injectors needs to be checked end-to-end. I use halogen headlight bulbs to test powers and grounds. Puts a decent load on the wiring. If they can light up that, then they'll run what they need to run. If you can get the computer to ground and light the bulb using a short jumper, then the wire is bad to the injectors. Also make sure a pin didn't get bent over when plugging the computer connectors back in, and that the female terminal puts enough tension on the male terminal to achieve continuity AND the ability to carry a load.
- The Peckish Synapse
  
  By Grumpy Bear · Posted 5 hours ago
  
  Let me introduce you to my Mirage 1.2 three pot with a CVT! Know what a Mirage can pass a Hell Cat Hemi can't? 😉
- The Peckish Synapse
  
  By OnTheReel · Posted 8 hours ago
  
  I spent a fair amount of time in the 2018-2024 versions. Had two different Equinox and a Terrain as loaners when my Silverado was down (regularly). I actually really liked them. Very comfortable. Efficient. The GMC was a SLT and had a reasonably nice interior too. And I’ve seen a lot of them go high miles with the 1.5. Unfortunately for me I’d have to go 2.0 because the 1.5 is SO SLOW. I know it’s not a performance vehicle anyway but I just can’t drive that much of a dog. The Malibu I had with the same motor wasn’t much peppier. These tiny engines just can’t move these bigger cars very well.
- 07 yukon xl 6.2 stalls at hot idle and wont restart
  
  By xdieselmechanic · Posted 8 hours ago
  
  All injectors are loosing the ground side from the pcm even with all injectors unplugg there is still.no ground pulse on any injector
GM-Trucks.com Clubs
- Black Truck Club
  
  Open Club · 612 members
- White Truck Club
  
  Open Club · 380 members
- Canadian Owners Club
  
  Open Club · 282 members
- Red Truck Club
  
  Open Club · 157 members
- diesel 3.0
  
  Open Club · 281 members
- Texas Owner's Group
  
  Open Club · 371 members
- NorthSky Blue Club
  
  Open Club · 118 members
- Midwest Owner's Group
  
  Open Club · 213 members
- 2015 Custom Sport Club
  
  Open Club · 5 members
- GM Snow Plowing Club HD
  
  Closed Club · 14 members
Popular Contributors
- Week
- Month
- Year
- All Time
1. 1
  
  Grumpy Bear
  15
2. 2
  
  diyer2
  14
3. 3
  
  Atlas
  10
4. 4
  
  newdude
  9
5. 5
  
  KARNUT
  9
Show More