Jump to content

Drum Brakes

c03camson
 Share

Recommended Posts

c03camson Enthusiast

c03camson

Posted
Posted

going to paint my stupid rear drum brakes and I cant get the damn things off. There is no retainer clip keeping them on so do i need to just beat them off or is there an easier way? I took the rubber plugs off the back and not really sure what im looking at in there.

Daryl LBZ Senior Enthusiast

Daryl LBZ

Posted
Posted

I think I always just hit them with a hammer on the front of the drum in about 3 spots. After that they would be loose enough to pull off.

desrtrat Senior Enthusiast

desrtrat

Posted
Posted
I took the rubber plugs off the back and not really sure what im looking at in there.

if you look in the hole, you should see a star wheel, and a latch on the wheel. if i remember right, take a small screw driver, or a pick and move the latch away from the star wheel, and with a med. size screw driver, turn the star wheel up 2-3 full turns. that will contract your break shoes enough to pull the drums off..

when your done :uhoh: remember to re adjust your breaks again, so you don't crap your paints the first time you apply your breaks.. :lol:

 

hope this helps.... :thumbs:

Matt_ Senior Enthusiast

Matt_

Posted
Posted

On a relatively new vehicle you shouldn't have to un-adjust the shoes to get the drum off. Give the hub surface a few good whacks with 2lb hammer in 3 equally spaced spots; this will break any bonds loose. At that point, you should be able to pull it off.... sometimes i find that its easier to pull off if you rotate it at the same time, so make sure you have the other side in the air and the wheel off.

Silverado4x4 Senior Enthusiast

Silverado4x4

Posted
Posted

They always freeze up at the axle hub, spray some wd-40 at that area and let it sit for awhile then the hammer method. You do have the parking brake off right? I have to ask because I have seem people wear them selfs out and figure out the parking brake is still on.

sc4808 Enthusiast

sc4808

Posted
Posted
They always freeze up at the axle hub, spray some wd-40 at that area and let it sit for awhile then the hammer method. You do have the parking brake off right? I have to ask because I have seem people wear them selfs out and figure out the parking brake is still on.

 

+1, I have seen the same thing.

c03camson Enthusiast

c03camson

Posted
  • Author
Posted

yeah parking brake was off. I was just trying to get them off so i could paint them. couldnt get them off so i just taped everything off, primed and painted them with the drums still on. worked like a charm. pissed me off though.

nqabigt Enthusiast

nqabigt

Posted
Posted
They always freeze up at the axle hub, spray some wd-40 at that area and let it sit for awhile then the hammer method. You do have the parking brake off right? I have to ask because I have seem people wear them selfs out and figure out the parking brake is still on.

 

 

+2 right side took a couple of taps, left side had to soak for a few minutes

FarmerDave Enthusiast

FarmerDave

Posted
Posted (edited)

Use a heavy rubber mallet, hit the drum on the farthest inboard edge of the drum in two spots across from each other. I clean my drums every tire rotation so mine always come off easy. But this is how I get the drums off transport trucks.

 

Edit: There are no retaining clips or any device holding the drum on other than the wheel + lug nuts.

Edited by DaveV
  • 5 years later...
danthesurferman New Member

danthesurferman

Posted
Posted

I second the two bolt method, although I have also had to use the small screwdriver to push against the locking tab and back off the star-wheel adjuster with a brake adjustment tool because the shoes were so far gone the metal was grooved into the drums. (not my truck). I recently made a YouTube video showing how to do it.

 

 

​

Janster Enthusiast

Janster

Posted
Posted

You can put some 'anti-seize' on the flat surface of the axle - where the drum comes in contact with it. I also put anti-seize on the lug nuts.

  • 5 years later...
DaveRave New Member

DaveRave

Posted
Posted

Size of the holes on my rear brake drums (2006 Silverado LS1500 V6 Std cab long bed 2WD 5spd) is 10 mm 1.5 thread and 25mm in length. You can probably get away with shorter ones like 20 mm. Took me two trips to HomeDepot to find this out since I misplaced ones I used previously. Mine will be free once again.

DaveRave New Member

DaveRave

Posted
Posted

Final caveat - this should pop (audible sound) the rust bond between the hub and drum. You can certainly help it along by applying penetrating oil or pounding on the drums between the studs. However if your drums are grooved you may still have to loosen the adjuster(s) to remove the drum(s). I would caution against using too much heat since the brake cylinders do have rubber boots around the pistons and the drums may be brittle or worn so go easy with the pounding also. If you are replacing the drums then by all means have your way with them. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • asilverblazer
      Intermittent no-code issues on 2022.5+ V8 trucks — what did the shop fail to capture?

      By asilverblazer · Posted

      Length/amount of data capture will be important to consider, sifting through 5 minutes of a data log can be enormous when it is stored in milliseconds. Being able to find the 'event' let alone decipher it.   Presumably the driver would notice something and hit a button to capture the 'window' of data. That window has to be large enough for the operator to recognize the event and react accordingly.    The data has to be able to be retrieved easily.   The data has to be able to be understood. Which is the biggest challenge, dealer techs won't even know what most of it is and would likely not even look at it if an owner brought it to them. Meaning the owner, the least educated/qualified, trying to understand it.    How will the data be presented? Could specific PIDs be selected and a timelapse graph be watched? How will a specific value be noted as abnormal? Additionally, a good data logger would be able to 'learn' normal values for a specific vehicle and flag abnormalities automatically. It could in theory watch parameters degrade over time and suggest maintenance as needed. (If the MAF reading begins tapering off for a given set of other readings - MAP, throttle position, Ambient, etc.. a flag to check air filter.) With the amount of data available, a device (really the vehicle rather than an additional accessory) should be able to do more than issue a DTC. It should be able to run the full diagnostic suite automatically and present a solution rather than a code. (It's not the 90's anymore). The technology is available for the vehicle to not just say "P0087", it should know low fuel pressure, check other PIDs to narrow down the problem itself, and determine if it is a lift pump, high pressure pump, regulator, leak in the fuel line, clogged filter, etc. Even if it can't narrow it down, it should be able to guide the user to the likely problems.   This would be a major problem for dealer service departments, which are the manufacturers customers it is in their collective best interest to NOT have this available to the consumer.   Further, if the owner is going to be the primary consumer of the data, it's got to be at a consumer price point vs. dealer only specialty tool price.   This group is more 'involved' in their vehicle than general public/consumer and will have knowledge, experience, needs and desires that are quite different from the market at large.   
    • KARNUT
      OCI, not when but why?

      By KARNUT · Posted

      I put the prof up. If you read what I posted. You can see that housing, cars and income are in line with the era we were talking about. It’s harder in some places easier in others. Let’s agree to disagree and put this back on track, OK? We both are pretty stubborn and hard headed. But I bring receipts. If you wish I will not respond to you in the future. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      Lets see if I can sum up two pages of nothing useful.    You want to refute your own governments data of the "Purchasing Power" Index FOR THE ENTIRE USA and its territories replacing it with the experience of a single family and its business and label that reality?  Then pound on that for a week hoping it will find traction?    Stan, I've told you several times. I don't do irrational. There are more people in the USA than your family.    I'm pretty sure this tread is so blown up. I'll give you a few days or months if need be to post yourself silent then I'll see if I can find enough parts of the train to reassemble it. 
    • asilverblazer
      VSE CCV Bypass - Anyone have this installed in their L5P?

      By asilverblazer · Posted

      Facebook groups hate VSE, poor customer service; their responses to criticisms are pretty poor for a reputable company. I'm not a customer, haven't bought anything from them, but how they handle themselves on social media is a definite "No" for me. 
    • asilverblazer
      Transmission Woes :-(

      By asilverblazer · Posted

      $10,000 for a transmission?   Pretty sure I could buy all the parts, tools, and education to rebuild it myself for a quarter of that amount.   or swap it out with a new one...

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...