Jump to content

Trying to find a reliable auto transport company


Shatterz

Recommended Posts

Posted

Hey All,

 

Within the next week or so I need to find a auto transport company to ship a vehicle from Wisconson to New Jersey (where I live). Vehicle in question is a mid 1980's K30 Pickup.

 

Never shipped a vehicle before so looking for suggestions and recommendations on who to use. If there is a chance someone on this board does auto transport, please let me know, it would be great to do business with a forum member.

 

Any suggestions are much appreciated.

Posted

There's are shipper in Wis called "Country Side Auto" I beleive the name is, they handle GB packers players cars so they probably are good.

 

http://countrysideauto.com/

 

3_packers_sm.jpg

Posted

Just looked them up on a load board that is not openly public & they were 100% rated.

 

I quit going that far east due to the toll roads. I was spending $100-$120 for five axle set ups on a round trip from IL-NJ & back. Have heard they have all went higher since my last trip out there in 2010. :nonod:

Posted

if you got the cash just fly here, and drive it back..i know a few guys that buy their dodges out west cause they come configured differently or something and i guess they find it cheaper to just drive it themselves...

Posted

if you got the cash just fly here, and drive it back..i know a few guys that buy their dodges out west cause they come configured differently or something and i guess they find it cheaper to just drive it themselves...

 

 

I've done that twice. Once to Chicago and the other time to Newark NJ.

Posted

if you got the cash just fly here, and drive it back..i know a few guys that buy their dodges out west cause they come configured differently or something and i guess they find it cheaper to just drive it themselves...

 

 

I've done that twice. Once to Chicago and the other time to Newark NJ.

 

 

screw driving in chicago....last time i got stuck in that rat maze for 3 hours..then as i was leaving saw a big sign that said "hell is real"

Archived

This topic is now archived and is closed to further replies.

  • Latest Articles

  • Posts

    • No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.
    • I have an observation and a question... 1) I watch the voltage closely because I have had to dial in the cut-in/cut-out voltages of the battery separator to my camper.  The "smart" charging drives me nuts.  Anyway, I noticed that when coasting for a while, and especially if lightly using the brakes (though not necessary), the voltage goes up from mid/high-13 volts to mid/high-14 volts.  Then it drops back down after stopping or going again.  Consistently!   The only explanation I can come up with is REGENERATIVE BRAKING!  Well, maybe that's a little bit of an exaggeration, but it's certainly free extra battery charging.   2) Driving on mountain roads I will use L and vary the max gear.  Things straighten out and I end up in L10.  Sometimes I leave it there for a while.  Is there any difference between L10 and D?   
    • Do you think this width might affect the chalk test with a higher pressure closer to 65psi? I think lowering the pressure makes sense to get the tread to lay flatter
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...