Jump to content

When to use 4x4


Recommended Posts

Posted

Just thought I would toss the question out there - How bad does it have to be before you use 4x4 in the snow? We got just over a foot here over the last couple weeks and I have really only used it to get me out of a couple sticky situations?

Posted

That depends . I driven my truck in a foot of snow perfectly fine dont know if i would want any more snow . I think just leave it on auto 4x4 and if you dont have auto just turn it on when you are going to get stuck. It mainly depends on your tires if you need 4x4 or not. Even in canada people rarely use there 4x4 the roads are good enough. I think 4x4 is good for steeper hills but for the most part your not going to need it much.

 

I have been in my dads old f250 with chains all around in 4x4 and it was pushing snow over the hood. I dont think the newer trucks can do that now stock . There ground clearance is crap . Whats nice about 4x4 trucks is that they sit higher and have the low range gears, and if you need the 4x4 (rare) its there to help out.

Posted

I dont use it much in the snow if i am on a road

 

Sent from my ADR6400L using Tapatalk 2

 

 

Posted

I use it when 2WD is no longer able to provide traction. Or simply if I think 2WD might not be enough. No real hard set defining factors.

Posted

I always stay in 2 unless I need 4, or if I'm at a intersection that is very slippery I'll throw it in 4 so I'm not spinning everywhere.

 

Now if we are out playing around in the snow I'll judge it by what we are looking at going through. Sometimes you just know you'll need 4x4. :driving:

Posted

What's this snow y'all speak of?

 

Sent from my SAMSUNG-SGH-I927 using Tapatalk 2

Posted

Use it any time you feel the need for it. Pretty much any time except dry pavement is OK, so if your unsure, lock it in.

Posted

I dont like the auto, you can lose rhe sence for how good or bad the road may be. For my its 2wd till it starts to be a pain to start moving from a stop then its time for 4x4. If you run auto it can be icy or something and you dont notice till u try to stop

 

Sent from my ADR6400L using Tapatalk 2

 

 

Posted

This^^ I haven't seen any drifts over 2 ft here in the last 2 years.

 

 

This pic was from 2010 in February up here. This storm shut us down for 2 days, 24+ inches of snow with 40 MPH winds. Took me almost 2 hours to plow my drive with the JD 4040 with a plow on the 3 point hitch.

 

Wish I would have taken another pic driving the tractor over to mom and dad's to do their drive. The walls of snow on each side of the road after they plowed were almost eye level with me in the cab. It was AWESOME!

post-71733-0-08233000-1354917673_thumb.jpg

post-71733-0-08233000-1354917673_thumb.jpg

post-71733-0-08233000-1354917673_thumb.jpg

post-71733-0-08233000-1354917673_thumb.jpg

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,980
    Total Members
    8,960
    Most Online
    Fishboat
    Newest Member
    Fishboat
    Joined
  • Who's Online   4 Members, 0 Anonymous, 629 Guests (See full list)

  • Latest Articles

  • Posts

    • Hey guys, sorry for the confusison about this. This wasn't my experainnce, it was copied and pasted fom the net. 
    • The problem with failure rates or increase failures are there’s people who don’t have a problem. What are you doing wrong they say. We had 4 5.7 GM diesel’s in the family when they came out. One was flawless. My uncle who happened to be the most abusive. Early rotary engines were known to use oil. I abused my first car so bad in six months I replaced the clutch, transmission and rear end. It didn’t use oil. My brother in law has a 2013 Tahoe and an older Yukon. The Yukon has 280K miles. The Tahoe around 175K. He runs them to about 300K. If his lifters fail before that time he would consider it a failure. My Hondas, I know people hate it when I mention them. Identical engines. One with cylinder deactivation one doesn’t have it. One shudders when the eco light goes on or off. Cylinder deactivation. But wait! According to the web. It can happen with lock up too. So now people in the know are changing the oil and transmission fluid more often. Then you read it could be a programing issue. So what do you do? There’s lots of money involved. I see three ways to deal with it. One only works if you don’t drive lots of miles. Lease, never get out of warranty. Or only buy older vehicles with a good track record. They all have bad runs. Usually when there’s a change. Even Toyota and Honda. 
    • Question @diyer2 on this line if you please. Are you saying the shudder is the system turning on and off at the frequency of the shudder? Guess I'm asking if you are saying you have seen it do this with the bi-direction scan tool in graph mode? If so have you been able to discern the 'trigger'. Something is telling to cycle rapidly.    My truck just started doing this recently. 197K on the clock. My response has been M5 anything under 55 mph. I treat it like a lugging stick shift. Gear down and let it spin a bit. Engauge M5, then tow mode and then M6 lets the trans stay in 5th but the AFM is active. Smooth like Skippy.    My thought was that as a machine ages the friction gets lower and as the system is load based, the lower friction would allow it to turn on at ever lower rpm until it reaches the lugging point. And yes I am ignorant of any minimum rpm requirement for the system. If you know that would be useful information.    As you know I run a Scan-Gauge II which allows me to watch the On/Off of the signal to the VLOM. While in the shudder mode I'm not seeing is cycle at that frequency or at all for that matter outside the triggers @newdude posted a few years back. Now is it possible that the refresh rate isn't fast enough to catch it? Maybe. It is why I asked my first question about graphing and trigging parameter.     As we have observed from members here the failure point is all over the map miles wise as you note yourself in your opening post. That by itself begs a few questions like fellows that comment on these lifters failing even after the system has been disabled. Long after. 😬   https://www.enginelabs.com/news/tech-tips-replacing-ls-active-fuel-management-lifters-with-melling/   The Gen5 lifters operate the same as the LS versions. In fact they are the same lifter.    https://www.enginelabs.com/tech-stories/sorting-out-gen-v-lt-lifter-failure-with-a-simple-valvetrain-fix/        
    • UPDATE 2: Steering wheel control backlights and control of the cluster can supposedly be achieved by adding a wire to pin 20 of the cluster and tapping it to pin 2 of the main clock spring harness. I'm going to give it a shot - will update  
    • GM Global A pickups 2019-2022 can do OTA programming for the radio.  GM VIP (GM Global B) can do OTAs for almost every module on board.  So a 2022.5 and newer pickup can do OTAs for recalls like the 2.7 fuel flow recall.  EVs get OTAs that improve one pedal driving, radio issues, HVAC issues, updated battery management software, etc.     So age of the vehicle/what GM electrical platform its on will alter what amount of updates can be pushed on OTAs.  
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...