Jump to content

Plow plates

timstech
 Share

Recommended Posts

SMiller Senior Enthusiast

SMiller

Posted
Posted

Correct me if Im wrong here but are the Fisher and western Plow mounts not the same ???

No they are not, the Western arms you simply pull the pin and the entire arm comes off leaving only the mount tucked up in the bumper.

George C Enthusiast

George C

Posted
Posted

The western plates sit a lot lower than the Fisher. IMO, Not enough ground clearance when mounted on a 1500.

SMiller Senior Enthusiast

SMiller

Posted
Posted

The western plates sit a lot lower than the Fisher. IMO, Not enough ground clearance when mounted on a 1500.

But you just pull the pins and there is nothing hanging down.

George C Enthusiast

George C

Posted
Posted (edited)

But you just pull the pins and there is nothing hanging down.

That is true, but you probably won't be pulling the push plates until spring.

The Western PPs also hang our further than the Fisher.

Edited by George C
mrbadwrench Enthusiast

mrbadwrench

Posted
Posted

I like that mount. It's a lot nicer looking than my SnoWay mount. I like my SW because of the downpressure, but the mount annoys me. I smack it on everything all the time...curbs, parking stops, dips in the road. It hangs low.

 

IMG_20140915_175437968_HDR_zpsgcvt6rwf.j

 

IMG_20150928_143852305_HDR_zpshw9uq84y.j

SMiller Senior Enthusiast

SMiller

Posted
Posted

I like that mount. It's a lot nicer looking than my SnoWay mount. I like my SW because of the downpressure, but the mount annoys me. I smack it on everything all the time...curbs, parking stops, dips in the road. It hangs low.

 

IMG_20140915_175437968_HDR_zpsgcvt6rwf.j

 

IMG_20150928_143852305_HDR_zpshw9uq84y.j

Looks a lot like a Boss plow mount, I would love having down pressure for back dragging!

  • 2 years later...
MJTurner42 New Member

MJTurner42

Posted
Posted

How far out do the Fisher mounts stick past the bumper.  That may be a tough selling point for me, carrying around all that extra hardware and bumping into things in the summer

badge171 Enthusiast

badge171

Posted
Posted

This is My 17 , Its the same Fisher set up that was on my 99 silverado, I keep updating , and painting, Mind you I don't do a lot of Plowing anymore , But at one time my account's numbered 30-35 residential . This last refit from my 11 to the 17, Side-plates were the same. just needed 1 wiring harness. I do the installs. I know mine does hang lower, but for me that does not justify the cost of new. Now if a v-plow would work on the 1/2 ton short box regular cab, that I would consider.

DSCN1005[1].JPG

  • 4 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,897
    Total Members
    8,960
    Most Online
    ncleg
    Newest Member
    ncleg
    Joined

  • Who's Online   2 Members, 0 Anonymous, 1,350 Guests (See full list)

  • Latest Articles

  • Posts

    • dna9656
      New to Me 2010 SLE (Quirks, Issues)

      By dna9656 · Posted

      Your tire pressure issue may just be batteries, you can reset them using tge Ing switch (I think) and the owner's  manual. ChatGTP will b e a faster, better help than Google.
    • Another JR
      Towing In Loose Gravel

      By Another JR · Posted

      The thinking is that starting out in a higher gear makes it easier to avoid applying excessive torque when pressing the gas pedal. In a modern 4wd truck with 4 low and a limited slip or locking rear end, I would use 4 low and try to crawl up the ramp. Sometimes if they are too slippery, you have to back up to let the boat have some bouyancy, and then accelerate briskly to get some momentum to help you pull the through the slippery parts. 
    • XY74
      Roll up bed cover experiences

      By XY74 · Posted

      I have a Retrax pro that I first had on my 2020 chevy and transferred it to my current GMC.  It stays in the garage most of the time, so hard for me to judge it's long term weather resistance.  It still works perfectly, been very durable.  It doesn't see oil patch usage, but it's not a mall queen.  It keeps most things mostly dry (small leaks) and the security of it is enough to slow someone down but not keep them out for long.  I would buy one again, it works for me.     
    • fm2176
      New to Me 2010 SLE (Quirks, Issues)

      By fm2176 · Posted

      Thanks to the convenience of Amazon, I was able to get a few things done to the truck today.  I installed Carquest Premium oil and air filters with five quarts of Mobil1 High Mileage 10-30 along with a quart of Pennzoil Platinum 5w-30 I already had.  The latch for the flip up center console lid was broken so I replaced it along with the power mirror switch.  I found my push retainer assortment this morning and reattached the plastic under the bumper and it was only held on with a few screws and retainers.  Then I programmed a new remote keyless entry fob so I can lock my dog in the truck when I take her out with me (I've got to keep the air going for her since it's been in the 100s).  Finally, I ordered some LED interior bulbs and replaced the reading lamps.  The front lights are working fine while one of the back lights only works intermittently and the other not at all.   While under the truck, I found the source of at least one of the noises: the sway bar links need replacing.  I ordered a set of Suspension Dudes links with Code Red bushings.  Never heard of them, but they're made in the USA and have decent reviews.  While making yet another Amazon order, I went ahead and added a set of front tow hooks.  I went with red, since that's the color of the sway bar link and bushings and it should look decent enough on a black and chrome truck.  Speaking of which, it doesn't bug me much, but the passenger side mirror has a chrome cap while the driver side doesn't, so eventually I'll make them match one way or another.  Oh, and I ordered a $20 TPMS reset tool.  No idea if it will do anything for my sensors but it was cheap and will work for the Ford Transit Connect as well.     For tradition's sake, I ordered a new oil change wrench.  I kept the Snap-On 9/16"x15mm GM wrench I bought when I was 18 in the 2006 GMC from the time I bought that truck until the truck was lost.  While I was tempted, there's no need to spend $80 for a new SO wrench, or even $50 with shipping for a used one on Ebay.  I just bought a Duratech 15mm extra-long ratcheting wrench to do the job as needed.  It works, and if I like that wrench enough, I'll buy the set.  
    • Another JR
      Multigate electrical problem

      By Another JR · Posted

      The recall is for exactly this issue - those drain holes combined with the limited environmental capability of the tailgate electronics card inside the tailgate were a problem. The “safety issue” was the potential for the tailgate to spontaneously open, but all kinds of tailgate misbehavior can occur from water contamination of that control card.    There is no real fix yet. The initial recall just disabled the tailgate. Later, when parts became available, they would replace bad parts with new parts of the same bad design. My dealer is going nuts because the few times I let them get their hands on my truck, my tailgate is off due to a slide-in camper installation. They really want to cut my tailgate wires, but I won’t give them the chance. I will let them get their dirty hands on it when a real fix (redesign) is available.  My tailgate, which works just fine with sealant plugging the drain holes, will remain safe in a dry storage crate until then.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...