Jump to content

ANTS EVERYWHERE


Recommended Posts

Posted

So I park my truck in a parking garage at BART in California, I come back to see small ants in a line from the bed, across the top of the passenger side doors, and down the hood/fender crack! Drove down the highway to see if they would just go away... this morning I wake up and they are still there and now INSIDE THE TRUCK! Time to torch the whole truck? I have never had this happen before in the 4 cars I've had.. i don't eat in my truck either and honestly nothing even in the truck. What do I do to get ride of them? I don't want to "smoke bomb" the interior since it is a brand new truck.

Posted

Take it to the park where all the pigeons hang out, roll down the windows and come back in a couple hours. :ughdance:

Posted

galliher_nc link said vacuum, that's what I was going to suggest. After a good vacuum, frame the bottom to include the wheel wells with some bug spray. Framing the truck would eliminate a primary access route in the truck.

Posted

Ants were all over and inside my truck, Pest control said a recent heavy rain forced them to higher ground. I sprayed Indoor Bug killer around doors , carpet edges and let windows down a little to vent. Neighbor had to use a fogger inside her car

Posted

If I had ants this would be the best way to kill them all.. attn don't try this at home. Nor do I encourage anyone to do this.. silver ice 6.2 is not responsible for anything done on your behalf...

post-145646-0-55885400-1440824859_thumb.jpg

post-145646-0-55885400-1440824859_thumb.jpg

post-145646-0-55885400-1440824859_thumb.jpg

post-145646-0-55885400-1440824859_thumb.jpg

Posted

Install one of these over night. And I can guarantee you will be ant free in less than 24 hrs

Didn't know Alf was still around, thought he liked cats?

 

 

Ryan

Posted

Most important - don't use baking powder! A lot of people believe it kills ants and that's not true.

 

First vacuum as good as possible and then put some ant traps up; in the truck as well as in the garage / shop. Should be fine within a (few) day(s), depending on how many of them are around.

 

Good luck!

 

@Ryan....Alf loves toasted cats - huge difference here Lol

Posted

Some car washes have Ant packages...its more common than youd think, try your local car wash

Posted

A few years ago we had a similar problem with ants in the cab of my old 97 C1500. I killed them for a week and they kept appearing. Turns out that when sometime in the past when I had carried off the recycle material (plastic bottles) from our kitchen I had spilled something sweet like apple juice in the bed of the truck, and it was a like a magnet for these buggers. I did a thorough wash outside of the truck an din the bed, and a good vacuum inside the cab and they finally went away. The key was washing away the source of their food.

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,840
    Total Members
    8,960
    Most Online
    appletrav
    Newest Member
    appletrav
    Joined
  • Who's Online   0 Members, 0 Anonymous, 404 Guests (See full list)

    • There are no registered users currently online
  • Latest Articles

  • Posts

    • This is a 1/2 ton thing ONLY.  All HDs 2020-2026 have the two speed transfer case, with Autotrac as an option.     1/2 tons 2019-2026, regular 4x4s come with a single speed case (no 4LO!), and trucks with Z71 ordered, or all Trail Boss trucks come with the 2 speed case.  2 speed case is also an option on WT, and is also standard on High Country.  
    • 2013 5.3 still to this day calls for the PF48 filter.  Which as a 15psi bypass pressure.     There is a TSB, 17-NA-157 that talks about the PF-63 and PF-64 filters which have a higher bypass rating of 22psi.    TSB HERE - temp.xml   "Beginning in 2012, the oil pumps began to regulate main gallery feedback instead of pump out pressure. This means that the oil pump now does not begin to regulate until pressure is built up to the main gallery. This change reduces the amount of time it takes to provide oil to the engine bearing and lifters during extreme cold start conditions.  Main gallery feedback oil pump control systems are present on the following engine families which use Spin-on oil filters: Small Gas Engine (SGE), Large Gas Engine (LGE), High Feature (HFV6) Gen2 and Small Block Gen5 gasoline engines. These engines with the main gallery feedback oil pump control systems are factory built with an ACDelco® oil filters"   It also calls out what engines use those filters.  The gen 4 small blocks were not on that list (LMG, LC9, L9H, L92, L94, L20, L96).  Gen 5 small blocks use the higher pressure filter.          That all said...   Your 7045 Napa filter is the PF63 equivalent, with 22psi bypass.  You are already using the higher bypass pressure filter.  You CAN keep using it, you don't technically have to use it though.  
    • Do you know WHY the filter relief setting was increased to 22 psig?    When the new system goes into the second stage the pump volume ramps up considerably. It was found that the 15 psi filter bypass setting put the filter in bypass on a warm engine when the second stage was activated. Raising the filter bypass setting forced the filter to do what it designed to do. Filter. Preventing debris from circulating during high load, high rpm operation.    So next question is how did GM find this out? VLOM/lifter failures and a deep dive by Melling Corp.    Last question. Is it required? Look at it like this; a motor may be equipped with a rev limiter. But it only works if the set point in reached. That 22 psig setting only matters if the pressure differential across the filter media exceeds 15 psig during normal warm operation. Second stage kicks in around 3000-3500 rpm.    I can't answer your question because I don't know you and how you use the truck. But I think there is enough information here to let you decide for yourself. 😉
    • Probably not their first rodeo, so it should go as planned most likely.  Typically the service manager or tech doing the swap will put some seat time to shake it down after they get it all put back together.  We usually put 50-100mi before we hand them back so if something happens, its not after you get it.  A coolant leaks, oil leaks, a ground left off or loose, vibration, etc.     The new engines so far have been good?  There's been a couple that have popped out there again (the replacement engine) but most have been okay.  
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...