Jump to content

New from Iowa - Getting a 2003 1500HD


Recommended Posts

Posted

Hello all, I am going to look at and, more than likely, buy a 2003 Silverado 1500HD this weekend. I will be traveling from Iowa to Kentucky which is roughly 10 hours. I have been looking for a 1500HD for quite some time and think I found the perfect truck. It's got 52k miles on it and looks to be in very good shape. The dealer was asking $17,999 for it but I got them down to $15,500. What are your thoughts on this price?

 

I currently own a 2004 Buick Rainier 5.3L but am wanting something a little more robust to trailer my Camaro to the track and our boat to the lake. The 6.0/4L80E combo is hard to beat for reliability. The Buick does an okay job towing the Camaro on an open trailer but the boat being 25' long would probably be a little sketchy. Right now I use my Dad's 2002 Avalanche and it even struggles a bit with it.

 

Here's some pictures of the truck.

 

10_zpsh3ziobrl.jpg

7_zpsuajmzart.jpg

9_zpsbx2j9ey4.jpg

12_zpscyhr5ivr.jpg

4_zpstbadkf2p.jpg

1_zps9st95uhi.jpg

3_zpsz6ddjz6l.jpg

 

The salesman I have been working with said there is hardly a scratch or ding on it and most importantly for me, no rust. Trying to find something like this in the upper Midwest that isn't a rusted mess isn't possible. I am going to make sure I keep it clean and do every thing I can to prevent the common rocker and cab corner rust issues that plague these trucks.

 

What do you all think?

 

For the heck of it here's the Buick towing my Camaro and the boat hooked up to it. I didn't go far with the boat. I know it would tow it but the short wheelbase and lack of weight wouldn't be wise I don't think.

 

DFD0CBEF-CDAB-4652-A53B-0AB2C02A0C8F_zps

Buick%20pulling%20big%20boat_zps1hrwq7og

 

I look forward to posting more.

 

Posted

Howdy neighbor!!!

 

Nice looking truck. You seem like you'll use it to its fullest :thumbs:

 

Thanks, Nick! I live in Madrid. Maybe I'll see you around!

Posted

The price sounded right and you are happy with it so that is all that counts.

 

As for keeping the rust at bay, some like to use AMSOIL's Heavy-Duty Metal Protector underneath as an undercoating. If interested let me know.

Archived

This topic is now archived and is closed to further replies.

  • Latest Articles

  • Posts

    • After I wrote that reply I went for a ride. 85 F out. So trans started at 85 F and it shifted the same as it did an hour latter at 168 F. I've never actually recorded the to cold to shift point but it is under 32 F before they start hanging on to a lower gear or leaving the converter unlocked. Both intended to heat fluid.    Yes, brake or bake. Absolutely.      Your welcome. True research ended decades ago. Field trials are still in play.    There is a thing called oxidation onset temperature. This is the heat related oxidation not the O2 exposure kind. For mineral oil that starts at 140 F. So what happens after 140 F? Each 20 F cuts fluid life in half! Does using a Full Synthetic improve that? Yes! By how much? Depends on the base oil type and a few other factors. But enough to notice. Some esters are even higher. There are even synergies between types the will raise it higher than any one component is alone.    Then there is "Hindered" oils. Antioxidant additives. Hindered Polyol Esters can sit at 500 F for years in a turbine.   When a blender brags his oil will 'take 500 F" in service he doesn't specify for how long. Water will dance on a 500 F hot plate for several seconds. @newdude put up a chart showing the relationship between fluid temperature and it's life in an automatic transmission. Here's a version of that chart for Group III based oils. These temperatures are those in the pan as observed as 'normal'. that is you drive as you do for as long as you do under what load you ask of it and whatever that temperature is this graph applies to. Flash temperatures of a few minutes isn't what his means.    Note that fluids held at a constant 240 F have a service life of only 20K miles. 220 F explains the factory exchange limit, eh? My equipment I keep under 180 F and I'm good if the cooler will hold it as low as 140 F. But that's me.   
    • Im in the same boat. Carlink adapter comes tomorrow and dev account is in process. Would you he able to send the new instructions my way also? Question, do you have to change code and republish app everytime developer updates? Thanks for your assistance, truly the only thing i cant stand about my truck is the carplay limitation 
    • Parts department or service department at the dealer.
    • I’ll take the blue one!
    • And Google AI says......... Yes, your truck can technically handle it, but you will be right at or near its maximum limit. A 2016 Chevrolet Silverado 1500 High Country with a 6.5-foot bed has a maximum payload capacity of approximately 1,770 pounds.Weight RealitiesLoad weight: Half a cord of dry hardwood weighs roughly 1,100 to 1,500 pounds depending on the wood type (like oak or hickory).Payload limit: Payload includes the weight of the wood, you, any passengers, and a full tank of gas.The math: If you weigh 200 pounds and have a full tank of gas, a 1,500-pound load of wood puts you right at that 1,770-pound ceiling.Safety TipsCheck the yellow and white sticker on your driver-side door jamb for your truck's exact payload number, as high-end luxury trims with extra features have slightly lower capacities than basic trucks.Expect the rear end to sag noticeably.Drive carefully, avoid sudden turns or stops, and keep speeds low if you have to travel a distance.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...