Jump to content

Which All Terrains for good mpg?

northslope

By northslope
in Tires, Wheels & TPMS

Recommended Posts

northslope New Member

northslope

Posted
Posted

I usually run LTX's but I have a leveling kit on this truck and want something a little more aggressive. I still want good mpg so not too aggressive and not too heavy of a tire.

I live in Northern Utah so I see a fair amount of snow. I also hunt and my tires will see some large sharp rocks. I drive a 2007 Silverado. Will be putting 18 inch rims on it.

Discount Tire guys are pushing their new Pathfinder which is made by Hankook.

What do you recommend?

Silver16 Enthusiast

Silver16

Posted
Posted

Cooper S/T MAXX. As for MPG no idea. Never pay attention but the tires are awesome off road. Got me everywhere I wanted to go and never got stuck.

LakeSpeed Enthusiast

LakeSpeed

Posted
Posted

I have Falken wildpeak at3w. On the highway, I notice less than 2 MPG loss. They have good road manners (quiet). Also, they have been very solid in what I consider deep mud. Disclaimer. I am in a 2500 Gasser. As a result, I am not focused on MPG

 

Good Luck!

  • 2 weeks later...
michigan2500hd Senior Enthusiast

michigan2500hd

Posted
Posted

Another vote for the Falken Wildpeak AT3. I didn't notice a millage loss from the factory Goodyear's. However a only put about 1000 miles on the Goodyear's. The Falken's have great road manners.. Period. Let alone that they are a pretty aggressive tread.

 

Sent from my E6810 using Tapatalk

I should also mention I went to a 275/60/20 which is 33.1" tall.

Lgetz Senior Enthusiast

Lgetz

Posted
Posted

On the old 2014 All Terrain with 295/55/20 Toyo AT2 mileage went down 1-1.5 mpg compared to stock Goodyears. Tire size, weight, and tread design factor into what mileage you ultimately get.

Loco-diablo Senior Enthusiast

Loco-diablo

Posted
Posted

A little aggressive, but I'm loving the 18" GY duratracs. Fairly quiet and I'm averaging about 21mpg all around (75% hgwy 25% city) with my Z71, 5.3 double cab. I'm looking forward to using them in the New England winter.

 

 

Sent from my iPhone using Tapatalk

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,982
    Total Members
    8,960
    Most Online
    nolankd
    Newest Member
    nolankd
    Joined

  • Who's Online   4 Members, 0 Anonymous, 440 Guests (See full list)

  • Latest Articles

  • Posts

    • Black02Silverado
      New Retail Account Promo

      By Black02Silverado · Posted

      For a limited time, retail accounts receive a free fender cover (G2803) with their order of $750 or more when they use code FENDER926 at checkout. The promotion runs through Sept. 8, 2026. Own a business and want to apply for a retail account?  Apply here. https://www.amsoil.com/business-opportunities/sell-in-your-store/?zo=521390  
    • Chuck FB
      Correct way to service 2024 l8t allison trans?

      By Chuck FB · Posted

      Thanks for that, yes just because I could I measured what came out just to give me some guidance although I already knew to expect it to take at least 9.5 to just throwing in the whole 10 quarts off the shot and doing a one and done heat cycle to drop out the excess to get to the proper level. I don't recall exactly now what I measured that came out but was less than I put back in, I knew I spilled some on the garage floor but the main part was that I was thrilled in the discovery I did not have to touch my exhaust to flex it down. The gasket manipulating is a pain of course to create that clearance to take the pan out and put back in but its all very doable if one is careful and not forcing the gasket to flex too much. From the quote I got at a transmission shop of 900.00 here in Canada ( never asked at the dealer what they charge ) I saved 700.00 doing it myself after paying for the supplies so that to me paid very good wages !, and I knew what fluid was put in and that I had changed the filter and that the level is correct without any doubts. 
    • bojanglespa
      2016 Sierra 1500 6.2L lifter Failure 🤨

      By bojanglespa · Posted

      I do have one of the AFM diasable box, using it for last 1.5 years.
    • Mellowth
      Tonneau cover and rack combo

      By Mellowth · Posted

      I found a setup that lets me open the cover partway with racks installed, using side-rail-mounted systems for easy access.
    • Chuck FB
      first oil change - 2026 2500HD gas

      By Chuck FB · Posted

      Typically its said and I agree so far that the engine oil drain plug oring is not required to be changed out unless you see some damage happening to the oring as apparently the oring lasts well. The dealer I have been getting a few parts from never even stocked the oring but instead stocked the whole drain plug that comes with a new oring which for the dealer is easier because they just throw in a new drain plug if there was any question about damage on it as well and charge the customer accordingly but again only if it is needed.    Also a hint about the drain plug oring to help it last vs a risk of causing damage to it, after its been removed and wiped off or washed off ( that is a whole other topic about some solvents damaging orings because some solvent types do ) to make sure to relube the oring with a bit of new oil so that it won't "grip" on the sealing surface of the pan and needlessly stress out the oring. Its no different than putting some oil on the sealing ring of the engine oil filter. So I just grabbed a new drain plug to have on hand although more recently bought just the oring as well but as its special it costs half the price of the drain plug ... !   Since you mentioned the hate to be empty handed theme, I am not sure what you have in the way of filter removal tools as I like using the exact sized for the filter steel 1" wide band with side to side swivel handle filter removal tool, and it can be used to snug up the filter without risk of damaging a filter as well ( its probably a lisle brand I have ). The drain plug hex size is 15mm and I always like using a 6 point socket if I have a choice and with this truck I've been using just a 3/8 ratchet that has a fairly long handle. Do you have a funnel that will work to pour oil in as that is definitely the short coming bastard part about the design with that fill port on the valve cover on such an angle that no normal funnel will even work. There are adapters and things on the market that will set into or screw into that fill port, I didn't want to deal with US shipping as that is all I was seeing at the time so caved and bought a Lisle brand multi vehicle fit adapter funnel kit and it really works well but there are much less expensive adapters out there that work in conjunction with an off the shelf funnel that would do the job also. Now that I have it, I like how it works and works so slick with the shape of the Amsoil 1 quart containers I have now switched over to. Whatever you do, have a funnel system of some sort as you will be swearing if you dropped the oil and then realize you have nothing to properly pour new oil in without spilling it all over the engine !.     Other comments, quite a bit of oil flows out down the filter when its cracked loose due to the housing above the filter so let it dribble down the filter until it slacks off flow and then remove the filter to create less possible mess. It seems these engines can sit for quite a while and drip and if you have time let it sit there and drip out of the engine as much as it wants. Also a good time to grease the 9 zerks on the front end, that's my typical practice anyway to grease the suspension and steering each time I change the oil. And remember to reset the oil change minder ( not something I am used to doing with older vehicles and equipment ). 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...