Jump to content

front driver noise after level lift!!!!!!!!!!!!!!!!!!!!

LASIERRA
 Share

Recommended Posts

LASIERRA Enthusiast

LASIERRA

Posted
Posted (edited)

I have a 2018 sierra 1500  z71 with 3000 miles on it. I added a 2.5'' motofab spacer under shock. now i have a noise coming from driver side front end. I see some other forums on here about it but no sure answers. Has anyone figured this out? If so please let me know the noise drives me crazy!!!! Mostly happens when going over several bumps at mostly slower speeds or on gravel roads. sounds like something is loose but everything is tight. 

Edited by LASIERRA
Sierra Dan Senior Enthusiast

Sierra Dan

Posted
Posted

Some have reported steering rack noises and failures relating to certain "Leveling" or after a Lift.

Should be some thread topics on the site here and there.

ksmobile2@gmail.com Enthusiast

[email protected]

Posted
Posted

I have had this same issue, Sierra 2500 slow speeds, especially rougher parking lots and gravel roads as well. Sounds like bumper, shocks or something loose,,,, I have a 2" dealer installed level, and was bothered by this, However, at 40k miles I replaced my Roncho "red" shocks and the noise and issue has diminished, but not gone. You have considerably less miles and would think your shocks would be the issue. I have heard of other " solutions"  but nothing helped. Knowing that you have a lift or level helps narrow it down.  "nothing loose" same here. 

 

sadly, more often than not, other guys fix problems and never post repairs that worked updates.

 

so, If you find something that works, share it  :)   I'll continue to look, other than removing level.... <<<<< might be the problem.

goheels New Member

goheels

Posted
Posted

Had same issue with my 2014 LTZ and unfortunately never found a cure.  I pulled the leveling kit and noise stopped so it was definitely in the kit. I put it back in and the noise began again.  Fortunately, it was intermittent and came and went.  Eventually it completely went away after about 50k miles on the kit.  Getting ready to put another leveling kit on my 2018 Silverado and am scared to death I am going to have same issue.

Good luck brother.

ammoaddict Enthusiast

ammoaddict

Posted
Posted

I have a 2018 Sierra 1500 as well, not lifted. I too hear noises from the driver side when my wife is driving. When I'm driving the noise comes from the passenger side. When I'm by myself I don't hear any noise.

Sent from my Moto G (4) using Tapatalk

  • Like 1
  • Haha 5
Castnblast67 Enthusiast

Castnblast67

Posted
Posted
I have a 2018 sierra 1500  z71 with 3000 miles on it. I added a 2.5'' motofab spacer under shock. now i have a noise coming from driver side front end. I see some other forums on here about it but no sure answers. Has anyone figured this out? If so please let me know the noise drives me crazy!!!! Mostly happens when going over several bumps at mostly slower speeds or on gravel roads. sounds like something is loose but everything is tight. 


2018 GMC Sierra All Terrain here, installed a 2” Motofab level last weekend. It’s the upper strut spacer, and no noise so far. I’m sure you’ve checked all your nuts, but make sure you got the sway bar end links bolted down all the way.


Sent from my iPhone using Tapatalk
Mozzer Enthusiast

Mozzer

Posted
Posted
I have a 2018 Sierra 1500 as well, not lifted. I too hear noises from the driver side when my wife is driving. When I'm driving the noise comes from the passenger side. When I'm by myself I don't hear any noise.

Sent from my Moto G (4) using Tapatalk


[emoji16][emoji16]
Has the wife read that?

Sent from my Moto Z2 Play using Tapatalk

  • Haha 1
  • 2 weeks later...
LASIERRA Enthusiast

LASIERRA

Posted
  • Author
Posted
On 2/9/2019 at 6:34 PM, Castnblast67 said:

 


2018 GMC Sierra All Terrain here, installed a 2” Motofab level last weekend. It’s the upper strut spacer, and no noise so far. I’m sure you’ve checked all your nuts, but make sure you got the sway bar end links bolted down all the way.


Sent from my iPhone using Tapatalk

 

I did but noise still there maybe I’ll try too spacer 

Castnblast67 Enthusiast

Castnblast67

Posted
Posted

Also check your sway bar bushings at the end links, make sure each of those are accounted for and are positioned correctly. On mine they kept popping out or didn’t want to back in the way they came out when I was bolting it all back together. Took some cussing to get them to cooperate. [emoji16] If there’s one missing or out of whack, could possibly result in some noise.


Sent from my iPhone using Tapatalk

  • 1 month later...
LASIERRA Enthusiast

LASIERRA

Posted
  • Author
Posted
On 2/8/2019 at 11:11 AM, goheels said:

Had same issue with my 2014 LTZ and unfortunately never found a cure.  I pulled the leveling kit and noise stopped so it was definitely in the kit. I put it back in and the noise began again.  Fortunately, it was intermittent and came and went.  Eventually it completely went away after about 50k miles on the kit.  Getting ready to put another leveling kit on my 2018 Silverado and am scared to death I am going to have same issue.

Good luck brother.

Did you put the kit on your 2018?

Donzi4me Enthusiast

Donzi4me

Posted
Posted (edited)

Leveled my '18 Sierra with Bilstein's set on top notch.   No noise, no rough ride.

 

However, I'm not up 2.5" either.   Ended up as advertised.  About 1.85"

Edited by Donzi4me
chefchoy Enthusiast

chefchoy

Posted
Posted (edited)

You guys should check out my thread for my truck.......my dad purchased a Silverado with 22k miles and it rattled. Mostly at slower speeds and on rougher terrain. I borrowed his truck one day and had to pull over on the side of the road cause I am really OCD and couldnt take it. I ended up deciding that it was coming from inside the cab to my surprise........I thought for sure it was a muffled sound from the exterior. Turns out, there is a metal belly pan that covers the steering shaft. All like 6 screws (with washers) were loose......I mean LOOSE! I tightened them up and good to go. Fast forward a couple years.......I purchased a 2015 GMC Sierra 40k miles. Exact same noise, exact same issue. Tightened the bolts, no more rattle. There are some pics on my thread if you wanna check them out. Should note.......One truck was manufactured in Canada, and the other Mexico

Edited by chefchoy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,866
    Total Members
    8,960
    Most Online
    Greg3160
    Newest Member
    Greg3160
    Joined

  • Who's Online   0 Members, 0 Anonymous, 507 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • MANGOAL
      Mangoal or FitcamX OEM Dashcam?

      By MANGOAL · Posted

      Late reply, but yes—it works on the SLT trim. Compatibility comes down to the plastic shroud shape behind your mirror, not the trim badge itself. On the SLT with auto-dimming, it uses a plug-and-play Y-harness off the mirror/rain sensor power, so no need to run wires down to the OBD port. If anyone's ever unsure about fitment, just drop a photo of your mirror housing and we can double-check it.   Appreciate the detailed feedback on the install! On the windshield glare—we actually took feedback like yours and developed a dedicated CPL (polarizer) filter to cut down dash reflections on sunny days. If you're still running the cam, shoot me a DM. I'd be happy to send a CPL filter over for you to test out—no charge. 
    • davester
      2002 GMC Yukon

      By davester · Posted

      There are no stickers in your glovebox?
    • davester
      Weight limit in bed

      By davester · Posted

      Look at the numbers on the stickers in the door jam...
    • EJS2015
      Actual Full Screen CarPlay on Refreshed Silverado/Sierras.

      By EJS2015 · Posted

      Yes, every time the developer updates his code, you must recompile. I will private message you with the latest because it changes pretty much with every version.
    • Grumpy Bear
      Transmission Temperature Hitting 220s

      By Grumpy Bear · Posted

      After I wrote that reply I went for a ride. 85 F out. So trans started at 85 F and it shifted the same as it did an hour latter at 168 F. I've never actually recorded the to cold to shift point but it is under 32 F before they start hanging on to a lower gear or leaving the converter unlocked. Both intended to heat fluid.    Yes, brake or bake. Absolutely.      Your welcome. True research ended decades ago. Field trials are still in play.    There is a thing called oxidation onset temperature. This is the heat related oxidation not the O2 exposure kind. For mineral oil that starts at 140 F. So what happens after 140 F? Each 20 F cuts fluid life in half! Does using a Full Synthetic improve that? Yes! By how much? Depends on the base oil type and a few other factors. But enough to notice. Some esters are even higher. There are even synergies between types the will raise it higher than any one component is alone.    Then there is "Hindered" oils. Antioxidant additives. Hindered Polyol Esters can sit at 500 F for years in a turbine.   When a blender brags his oil will 'take 500 F" in service he doesn't specify for how long. Water will dance on a 500 F hot plate for several seconds. @newdude put up a chart showing the relationship between fluid temperature and it's life in an automatic transmission. Here's a version of that chart for Group III based oils. These temperatures are those in the pan as observed as 'normal'. that is you drive as you do for as long as you do under what load you ask of it and whatever that temperature is this graph applies to. Flash temperatures of a few minutes isn't what his means.    Note that fluids held at a constant 240 F have a service life of only 20K miles. 220 F explains the factory exchange limit, eh? My equipment I keep under 180 F and I'm good if the cooler will hold it as low as 140 F. But that's me.   

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...