Jump to content

2017 Duramax L5P base idle

jaws3
 Share

Recommended Posts

jaws3 Enthusiast

jaws3

Posted
Posted (edited)

After the recent recall for Emission System upgrade to comply with gov standards (done 2 weeks ago) the base idle speed has increased to over 800rpm. Used to be just above 500rpm. Dealer says the higher base idle speed is "with limits". I don't agree. Talked to 2 drivers of similar trucks today and both said there base idle speed is just above 500rpm. These are company trucks so they don't know if recall upgrade was performed on the trucks they are driving. The exact scenario is that when I start the engine, idle is normal at just over 500rpm. It stays normal when shifting into DRIVE. Then start driving and at the very first stop 700m from my house, it base idle is over 800rpm. It stays like that until I shut down the engine and it is back to 500rpm when I start the engine again after work. But only until the first stop when it stays above 800rpm. This has been going on for the past 2 weeks (during which I also did a 1200km highway trip). I cannot find a reference to base idle speed on this engine. Is 800rpm considered normal? If it is my "new normal" I'll be selling the truck as it is driving my crazy with the added noise sounding like a jet engine at startup.

Edited by jaws3
spelling
2018GMC Senior Enthusiast

2018GMC

Posted
Posted

Go to a different dealer.
 

Example:

 

We had oil pressure gauge on lml suddenly read 120 psi anytime above idle. 

 

GMC dealer said there was no max spec for oil pressure just minimum. I suggested they change sending unit as everything was fine the first few years. They politely offered me an oil change I’d have to pay for  
 

I complained to GM customer care and setup an appointment with Chevy dealer across town. They replaced sending unit and all was back to normal. 
 

Original dealer must have gotten a call from GM because they called me and offered a free oil change as an apology. 

jaws3 Enthusiast

jaws3

Posted
  • Author
Posted

Good idea but not easy. Next dealer is 200km away from here...

redwngr Senior Enthusiast

redwngr

Posted
Posted (edited)

Aftermarket floor mats? 

 

Position sensor for skinny pedal loose or out of adjustment?

 

I'm not buying dealers 800 rpm soy either.

On the diesel sites lots have reported having the recall done -- no one has reported an increase in idle speed. 

 

 

Edited by redwngr
jaws3 Enthusiast

jaws3

Posted
  • Author
Posted

No aftermarket floormats. Everything as it was prior to the recall except the 800rpm. But thanks for corroborating that it is not normal.

redwngr Senior Enthusiast

redwngr

Posted
Posted

Good point ho

7 hours ago, hollywoodsle said:

image.thumb.png.0081ca072cbe96c063749b5018ad92c8.png

Good point.  

 

They can run high idle at startup, sorta like automatic choke on an old gasser.

And they can run higher for a reason like electical load, coolant temp and so on. 

They also will run higher shift points when cold.

 

My response was interpreting the op's description as never returning to a low idle once fully warmed to normal.  

 

curver900 Enthusiast

curver900

Posted
Posted

It will also run higher idle when Regen is active iirc on mine it is right around 800-900 rpm .  Make sure it completed a Regen.

 

jaws3 Enthusiast

jaws3

Posted
  • Author
Posted (edited)

Yes, idle never returns to baseline. This is not a "variable" idle rpm. It is over 800rpm all the time. Except at start up when it will idle at nase rpm  ut as soon as I drive off and stop the first time, it is above 800rpm and does not ho down until I shut down the engine

Edited by jaws3
Clarification
jaws3 Enthusiast

jaws3

Posted
  • Author
Posted
6 hours ago, white94rx said:

Your truck is in the middle of a regen. Drive it longer and when it's done the idle will go back to normal.

Sent from my Pixel XL using Tapatalk
 

Thank you white94. In my original post I stated this has been going  on for 2 weeks since the software update. It includes daily driving as well as a 1200km weekend trip. Surely that should be far enough? I have also noticed over the past 3 days TV that the gear change occuring just above 50km/h is very rough. As if the truck "jumps" at that changeover. Not sure if it is related but the truck is rapidly becoming very unpleasant to drive. Will make another call to dealer as that seems to be my only ootion. Apart from selling it.

curver900 Enthusiast

curver900

Posted
Posted
On 4/25/2020 at 11:31 AM, white94rx said:

That definitely should have been far enough. Mine usually takes about 20-30 minutes.

Sent from my Pixel XL using Tapatalk
 

Mine does it in exactly 20 miles if kept above 40 mph

jaws3 Enthusiast

jaws3

Posted
  • Author
Posted
1 hour ago, curver900 said:

A call to gm customer service is probably in order or have another dealer or this dealer reflash it

Have an appointment with the dealer next week to look at this again

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • PunchT37
      Parking Brake - Automatic Engagement Questions

      By PunchT37 · Posted

      I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...