Jump to content

Relearn TMPS

BlackRST
 Share

Recommended Posts

BlackRST Enthusiast

BlackRST

Posted
Posted

Has anyone "relearned" their TMPS when they put new wheels/tires on their truck? If so is there a specific sequence to do so?

 

Thanks in advance.

 

 

Sent from my iPhone using Tapatalk

goosehunter Enthusiast

goosehunter

Posted
Posted

Yes , have done it and do you have relearn tool......front driver, front pass, back pass. and back driver....should hear horn double beep if successful!    I bought a relearn tool on amazon.....cheap and it works!

 

BlackRST Enthusiast

BlackRST

Posted
  • Author
Posted
Yes , have done it and do you have relearn tool......front driver, front pass, back pass. and back driver....should hear horn double beep if successful!    I bought a relearn tool on amazon.....cheap and it works!
 

Okay, I bought the tool on amazon recommended from previous posts on the forums. I just was never able to locate the how to. If you wouldn't mind

1)Mount new wheels
2)then go wheel to wheel and press the button to relearn?
3) nothing in the dlc I need to select?

Thanks in advance.


Sent from my iPhone using Tapatalk
OnTheReel Senior Enthusiast

OnTheReel

Posted
Posted

You do have to put it in relearn mode from the DIC. It’s the same process as this vid for the last gen.

 

 

This is the tool I bought. There’s like 100 different listings for the same basic unit so I don’t think it matters.

 

2020 gm tpms relearn tool,OEC T5 Super EL-50448 Auto Tire Pressure Monitoring Sensor 315MHZ and 433MHz Car Tyre Compatible for GM Series Vehicle,Tire Sensor Reset Tool https://www.amazon.com/dp/B07X477966/ref=cm_sw_r_cp_api_i_xBkTEbE97T76S

 

  • Like 1
goosehunter Enthusiast

goosehunter

Posted
Posted

Yes go to tire monitor in DIC and once there press  and keep press until relearn is activated......once outside if you have cheaper relearn tool DO NOT AIM at valve stem, go to edge of rim and aim at inside sensor. Once it relearn that sensor the horn will beep once and go to pass front as stated...… if truck is equipped with right sensors( did you change them?) if truck is near go try it and update me.....  thanks!                         GH

BlackRST Enthusiast

BlackRST

Posted
  • Author
Posted
Yes go to tire monitor in DIC and once there press  and keep press until relearn is activated......once outside if you have cheaper relearn tool DO NOT AIM at valve stem, go to edge of rim and aim at inside sensor. Once it relearn that sensor the horn will beep once and go to pass front as stated...… if truck is equipped with right sensors( did you change them?) if truck is near go try it and update me.....  thanks!                         GH

Awesome thank you. Yeah I have a set of fuel wheels and tires on the way with new sensors mounted within. I double checked to get the correct ones mounted. I just was unsure on the process. Thank you, big help!!


Sent from my iPhone using Tapatalk
  • Thanks 1
BlackRST Enthusiast

BlackRST

Posted
  • Author
Posted

Thank you! I will give that a shot when the wheels arrive. I bought the same one, or damn near same one.


Sent from my iPhone using Tapatalk
Snakes709 Enthusiast

Snakes709

Posted
Posted (edited)
5 hours ago, BlackRST said:

 

Has anyone "relearned" their TMPS when they put new wheels/tires on their truck? If so is there a specific sequence to do so?

 

Thanks in advance.

 

 

Sent from my iPhone using Tapatalk

 


need the relearn tool. Its like $15 and super easy to use. Turn aux power on with engine off, bring up the tire pressure screen, press and hold the check mark button for approx 5 seconds. “Tpms relearn” will display and your left front marker light will be on. Place the tool below the valve stem and press the button. You will hear a honk, then go to the passenger front and do the same. Once you finish all 4 you will hear 2 honks and you are all done.  You have 5mins to complete it before it times out.  Shouldnt take anymore then 1min. 

Edited by Snakes709
  • Like 1
  • 2 weeks later...
BlackRST Enthusiast

BlackRST

Posted
  • Author
Posted

So I mounted my new wheels/tires. I'll be damned if I could get the scan tool to work. But I hit the dlc it said relearning and it honked twice and I haven't had any issues with the sensors they're reading fine.


Sent from my iPhone using Tapatalk

BlackRST Enthusiast

BlackRST

Posted
  • Author
Posted

Update: Went to the Chevy dealer and had them try and relearn the sensors with their scan tool. It wasn't even registering on their tool. After contacting realtruck.com they said they were having issues with the sensors "falling asleep" in transit. I was told to lower the pressure to 24 then raise it back up in each wheel to trick them into waking up. Yeah....no luck so now i wait. 

 

Side note: its unreal trying to get a solid answer on whats a good PSI for the nitto ridge grapplers. 

OnTheReel Senior Enthusiast

OnTheReel

Posted
Posted

Bummer. Frankly I would just have the OEM sensors moved over or buy another set of factory ones on eBay. Not even worth the time wasted on aftermarket sensors. 

  • Like 1
BlackRST Enthusiast

BlackRST

Posted
  • Author
Posted
Bummer. Frankly I would just have the OEM sensors moved over or buy another set of factory ones on eBay. Not even worth the time wasted on aftermarket sensors. 

Which is actually what I think I'm leaning towards. I'm waiting to hear back from my sales guy tomorrow. They'll Comp me the price of a mount and rebalance. So now I'm just waiting to see what I'm going to do with the sensors. I'm getting a quote from the dealer on 4 new ones as well to present to them haha.


Sent from my iPhone using Tapatalk
  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • newdude
      Gas fill door

      By newdude · Posted

      Common failure.  You need to replace the fuel door housing.   The painted cover transfers over to the new housing.  To remove the old one there is 4 spots where you poke the plastic to release it.  
    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      I have an observation and a question... 1) I watch the voltage closely because I have had to dial in the cut-in/cut-out voltages of the battery separator to my camper.  The "smart" charging drives me nuts.  Anyway, I noticed that when coasting for a while, and especially if lightly using the brakes (though not necessary), the voltage goes up from mid/high-13 volts to mid/high-14 volts.  Then it drops back down after stopping or going again.  Consistently!   The only explanation I can come up with is REGENERATIVE BRAKING!  Well, maybe that's a little bit of an exaggeration, but it's certainly free extra battery charging.   2) Driving on mountain roads I will use L and vary the max gear.  Things straighten out and I end up in L10.  Sometimes I leave it there for a while.  Is there any difference between L10 and D?   
    • devonthegreat
      anyone interested in a 2002 Chevy Silverado 4x4 parts truck NYC

      By devonthegreat · Posted

      **SOLD** Please end or delete post. thank you

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...