Jump to content

Play all music on USB key?

nichos
 Share

Recommended Posts

nichos Enthusiast

nichos

Posted
Posted

OK, this may seem like a silly question, but how do you play "all" music on a USB key after telling to play an artist or song?

 

For example, if I say "Play song Hotel California" it will play Hotel California, and nothing else. Hitting next just plays Hotel California again.

 

The same thing happens if I say "Play artist Eagles", it will only play the Eagles. How do you get out of that and get back to shuffling all songs on the USB key?

 

TIA!

redwngr Senior Enthusiast

redwngr

Posted
Posted

“Play <device name>” : Play music from a specific device identified by name. 

The device name is the name displayed when the device is first selected as an audio source.

 

There is a bunch of options for the "play <    >" command.

 

“Play Artist” : Begin a dialog to enter a specific artist name.
“Play Artist <artist name>” : Begin playback of a specific artist.
“Play Album” : Begin a dialog to enter a specific album name.
“Play Album <album name>” : Begin playback of a specific album.
“Play Song” : Begin a dialog to enter a specific song name.
“Play Song <song name>” : Begin playback of a specific song, if available.
“Play Genre” : Begin a dialog to enter a specific genre.
“Play Genre <genre name>” : Begin playback of a specific genre.
“Play Playlist” : Begin a dialog to enter a specific playlist name. 

“Play Playlist <playlist name>” : Begin playback of a specific playlist.
“Play <device name>” : Play music from a specific device identified by name. 

The device name is the name displayed when the device is first selected as an audio source. 

 

 

nichos Enthusiast

nichos

Posted
  • Author
Posted

Thanks @redwngr I guess I'm not understanding or I'm doing something wrong.

If I'm on my USB key, and select an artist, (or song) it will continue to play that artist. I can go to FM and come back to USB, it will continue with that artist.

 

I tried saying "play USB" and it switches over to USB, but continues on that 1 artist. How do you "exit" playing a single artist or song?  can't find a way to "shuffle all songs" or something.

 

thanks

redwngr Senior Enthusiast

redwngr

Posted
Posted
30 minutes ago, nichos said:

Thanks @redwngr I guess I'm not understanding or I'm doing something wrong.

If I'm on my USB key, and select an artist, (or song) it will continue to play that artist. I can go to FM and come back to USB, it will continue with that artist.

 

I tried saying "play USB" and it switches over to USB, but continues on that 1 artist. How do you "exit" playing a single artist or song?  can't find a way to "shuffle all songs" or something.

 

thanks

Does the usb you are using display a 'name' when it is plugged in?

 

Try using that name - "Play <usbname>

"Play usb' probably returns to playing the usb in the same mode as it was last used.

 

Is it playing songs in the order they are saved on the usb? 

 

When playing  a usb/album/playlist/artist there should be a 'shuffle' icon that can be pressed. 

(so the songs included in the shuffle would depend on what songs were included in the current play mode) 

nichos Enthusiast

nichos

Posted
  • Author
Posted

@redwngr no name is displayed on my usb, it just says "USB" on the left menu. Maybe i need to take it out and give it a name on my computer?

jgisonfire Enthusiast

jgisonfire

Posted
Posted

I think you need to make a playlist with all of the music in it, so you can then say "Play playlist [name]" and it would select from the full list of songs. Down side would be that it would probably play the same song to start, but with shuffle I think you'd be ok after that.

  • 5 months later...
nichos Enthusiast

nichos

Posted
  • Author
Posted
11 hours ago, Masert said:

Hello, I guess that you listen to music via Apple music app?

I'm using a USB key.

 

I still haven't been able to figure this out. The only way I know how to do this is to:

  • Say "Play song Hotel California"
  • Now I'm stuck on this single song.
  • To get out of it, I press the "browse" button
  • Select "songs"
  • Click on any song (doesn't matter what)
  • Now when pressing "next track" it'll go to a random song.

 

Pretty weird there's not a "exit artist" or "single song" option. I think ford is "shuffle all"

 

Jim E Enthusiast

Jim E

Posted
Posted

I had this problem when I first got my Camaro.  I think I had to turn off shuffle and turn it back on.  But that was 8 years ago, so...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      So, do I go elbow-deep on this thing or list it for sale and play dumb? Seems to "runs good."   I'm about $1200 away from having: -a rebuilt injector ($300) -a new cat ($250) -a new cat back exhaust (OE style) ($300) -a new AC compressor ($200) -AC refrigerant charge ($150)   In theory, this should rectify the obvious detracting issues from its value and operability. Cold AC with a non-squeaking AC pulley both sounds and feels good. An exhaust that isn't cut/hacked in 17 different places and doesn't vibrate on a crossmember would make it sound and feel less janky. A working cat would help the stink, and will save the earth, but *if and only if* the fuel system is working properly, which would also address the intermittent "rich" CEL.   Heard a good one... CEL for "Rich condition" means you haven't spent enough money on the truck lately, and it's letting you know.   Rebuilding the injector would seem to be the most important part. Replacing the cat would be secondary. I don't think mine is plugged or overly restricted, but it might be a little restricted? I have no good way to tell other than seat of the pants feel. I hate the smell.   The current theory is I have a rich idle problem: A bad fuel pressure regulator, or a leaking injector(s) being the highest probabilities. I already replaced the FPR but that doesn't mean its replacement isn't also bad. It was a new part from Dorman, but the packaging looked like it had been sitting on a shelf for 20 years.   This is the (single) upstream O2 sensor shown at idle. I'm getting a lot of "rich" it seems. Sometimes it stays high like that and doesn't drop down. That makes me think it's processing injector leaks or a partially stuck open injector.     Other times it looks like this. Nice oscillations between rich and lean, which is what I think it should be. Under load and at speed, the oscillations are nice and tight and uniform looking, high and low.     Fuel trims suggest the PCM is compensating pretty hard at idle to pull fuel out. But it's not enough to trip a CEL. Something about slowing to a stop: brake vaccum booster, EGR, or the EVAP purge is delayed, or there's pooled fuel in the intake again that's draining into a cylinder is enough to set the CEL. Of course, in two days of driving, it hasn't set. I was hoping to actually look at the freeze-frame data when it sets. IAT is high because it's idling on an 83 degree day here.  
    • Another JR
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By Another JR · Posted

      Have considered installing a DC to DC charger in your camper to replace your isolator?  
    • newdude
      Gas fill door

      By newdude · Posted

      Common failure.  You need to replace the fuel door housing.   The painted cover transfers over to the new housing.  To remove the old one there is 4 spots where you poke the plastic to release it.  
    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...