Jump to content

Tapping into fuses for a CB+PA Speaker/LED lights/Air horn.. which fuses are best to use?

LDelSanto86
 Share

Recommended Posts

LDelSanto86 Enthusiast

LDelSanto86

Posted
Posted

I’m looking to use some “Add-a-Circuit Fuse Taps” to power a CB with PA speaker, a set of LED lights, and a cheap airhorn on my 2016 Silverado LT.. I’m looking to have these only powered on when the key is turned to ACC/On/ or the truck is running. I’ve never done this before and I’m not the best with electrical. Any tips on which fuses to use? Should I up the size of each fuse or do they generally have some wiggle room when it comes to how much load they can handle?

 

Thanks!

 

 

Sent from my iPhone using Tapatalk

Racindave Enthusiast

Racindave

Posted
Posted

Don’t up the size of the fuse. I would use something that won’t leave you stranded if you were to blow them and not have a spare fuse. (Radio, Heater, etc..). For my LEDs I tied into the trailer running light fuse under the hood so mine would come on when the lights were on. (My leds are mood lighting in the floorboards.) they have a separate switch so I can turn them off if I’m tired of them.  

  • Like 1
  • Thanks 1
LDelSanto86 Enthusiast

LDelSanto86

Posted
  • Author
Posted
Don’t up the size of the fuse. I would use something that won’t leave you stranded if you were to blow them and not have a spare fuse. (Radio, Heater, etc..). For my LEDs I tied into the trailer running light fuse under the hood so mine would come on when the lights were on. (My leds are mood lighting in the floorboards.) they have a separate switch so I can turn them off if I’m tired of them.  

Thanks for the reply! The radio is a good idea, I’ll check into the fuse location for that! Dumb question but is there a way to max out the load on a fuse to immediately see if it can handle it? Or is it just something that can fail over time? I’ve got a buttload of spares and don’t mind blowing through them to find out what works - if I can find out in my driveway, not on the highway [emoji23]


Sent from my iPhone using Tapatalk
Racindave Enthusiast

Racindave

Posted
Posted

I personally wouldn’t try to blow it myself. Just try to find a fuse that is rated to whatever your gonna try to power. The add a circuit will only carry so much also... from what you say you want to power they should be fine. I’m not sure about the air horn but you might could just go straight off the battery with an in line fuse in the new power line. Put the inline fuse within 12 inches of the battery though. Take your time and do it right. Don’t burn down your rig trying to do more than the wires can handle...Have fun. 

  • Like 1
LDelSanto86 Enthusiast

LDelSanto86

Posted
  • Author
Posted

Thank you, I didn’t know in-line fuses had to be so close to the battery, that’s good to know! Yeah I think I will run the horn straight from the battery..I have a switch for it that lights up, which is why I wanted to go off an accessory fuse for it but now that I think about it I’m sure the light from that switch would take weeks to drain my battery so I probably shouldn’t have to worry about that being on constantly.


Sent from my iPhone using Tapatalk

Snowcamo Senior Enthusiast

Snowcamo

Posted
Posted

If you are not into electrical wiring I suggest not taping into the trucks fuse box. It's more safe( large margin for error) to run power/w fuse @ batt to a stand alone fuse block. Then from there you tap your accessories into. You can fry stuff quick if you know not what you do...?

  • Like 1
LDelSanto86 Enthusiast

LDelSanto86

Posted
  • Author
Posted
If you are not into electrical wiring I suggest not taping into the trucks fuse box. It's more safe( large margin for error) to run power/w fuse @ batt to a stand alone fuse block. Then from there you tap your accessories into. You can fry stuff quick if you know not what you do...[emoji58]

Thanks for the tip. Is it possible have things still switch on and off with the ignition that way? That’s the only reason I’m looking into tapping into fuses instead of going directly to the battery.


Sent from my iPhone using Tapatalk
lonestardiver Enthusiast

lonestardiver

Posted
Posted

Tap into a circuit that is on when the ignition is on or the engine is running. Use that to trigger a relay and run your own circuit to the battery with its own dedicated fuse near the battery. This prevents overloading your vehicle systems/wiring and keeps your accessories on their on dedicated circuit.

  • Thanks 1
Snowcamo Senior Enthusiast

Snowcamo

Posted
Posted
4 hours ago, lonestardiver said:

Tap into a circuit that is on when the ignition is on or the engine is running. Use that to trigger a relay and run your own circuit to the battery with its own dedicated fuse near the battery. This prevents overloading your vehicle systems/wiring and keeps your accessories on their on dedicated circuit.

This^^^ if i could like it a 1000 times i would. My thoughts exactly.

  • Like 1
flyingfool Senior Enthusiast

flyingfool

Posted
Posted

do a search for the upfitters schematics ,   pmoore4321  has the PDF's for where to tap into on K2 trucks. message him or go to his website and download it

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • pyoung62
      2026 DENALI 6.2L

      By pyoung62 · Posted

      I agree with Tim.  As tech heavy as engines are these days, no way I’d be an early buyer of the new 6.6.  Of course, I bought my ‘26 Denali w/the 6.2 after dumping my Tundra with it’s defective 3.5 liter imploding engine disaster, so I’m a little gun-shy.  That said, my 6.2 has been rock solid.  I don’t drive it like I do my BMW Z4 M40i, but I don’t baby it either.  I got a V8 for a reason.  But I’m averaging 18 around town and 22 highway.  I have seen 24 highway as well when I wasn’t loaded up heavy.  Considering my Tundra with the twin turbo V6 only got 14.5 in town and 17 on the road, I’ll take the 6.2 all day, every day.  If I were you, I’d grab a ‘26 while you can.  Inventories are probably gonna start dropping and I’ll bet the deals will start looking sweeter as well.
    • ShowMeShooter1332
      Can you add a 360° Cameras hard button to a 2021 Sierra?

      By ShowMeShooter1332 · Posted

      I am curious if anyone has figured out a way to add an hard button AUX or 360 Camera switch to the center row of switches. I have a 2021 AT4, and want to split the hill decent button and add a 360 camera button so that you don't have to go into the center display and locate the camera functionality, etc...   My father's 2024 Yukon XL AT4 and it has a hard button, see below. I found this thread on the Yukons, but it seems like there may not be a part number for the 2021 sierras. https://www.gm-trucks.com/forums/topic/255339-adding-hard-button-for-camera-on-2021/ Anyone else figured this out. Seems like it would need to be a custom switch!   I am getting ready to install the auto stop/start eliminator, so would be nice to knock them out at once.     Upvote1Downvote0Go to comments
    • Grumpy Bear
      Winter Returned

      By Grumpy Bear · Posted

      Looks like the entire state is burning. 😬
    • Chuck FB
      Oil Consumption

      By Chuck FB · Posted

      Through the years it hasn't been my typical method as I tried to drop oil on an engine that was hot from having been worked, however that was not always practical and had to fire up a unit and let it warm up reasonably well and drop the oil when I had the time to do it but am referring to not only vehicles but a variety of farm equipment and highway tractors etc. However on a vehicle where one is crawling under it and the exhaust is nearby to ones body and if wanting to pull the plug without danger of being hit with boiling hot oil or attempting to remove a HOT oil filter, its sure safer and easier to not have everything smoking hot and can remove the filter right away when under the vehicle and let it all drain. Of course its not the end of the world if a bit of oil stays in the engine that might have eventually found its way out, I like to get out as much as possible but any oil changes that take place in shops would rarely be sitting around for very long at all before the plug is thrown back in and filter slapped on and oil poured in and sent out the door quick like. There would be very little time spent ( assuming they even did it ) in starting the engine with oil to fill the filter, then waiting to verify the level on the stick. A good reason to check ones oil level shortly after a shop changed the oil on a vehicle just to make sure its correct and to look under for any oil around the drain plug or filter. 
    • CPhelps
      4 Wheel Drive System

      By CPhelps · Posted

      Cool to see another Vermonter!

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...