Jump to content

DEF Gauge stuck???

bonzman17
 Share

Recommended Posts

bonzman17 Enthusiast

bonzman17

Posted
Posted

I just turned 10k miles. I am thinking the float for the def gauge on my truck is stuck in the full position. It’s been at least 3k miles since I topped it off and I’ve smelt 2 regens but the level according to the dic is still full. It’s hard to believe that this uses such a minimal amount per regen. 
 

I’ve been on some bumpy roads and I have heard the fuel sloshing in the tank so I would imagine the def would be doing the same. Just wondering if anyone else has had the same issue. Think I’ll craw under it and tap the def tank (if I can get to it) with a dead blow a few times. 

redwngr Senior Enthusiast

redwngr

Posted
Posted

DEF is used whenever the engine is running.

It is NOT a regen only item.

 

During regen, the truck adds fuel directly to the exhaust to create the regen heat. It will add some extra DEF to respond to the extra NOx produced burning the extra fuel. 

 

If it's been 3000 miles since it was filled and the gauge still has all the LED's lit I'd agree it's probably not displaying correctly. 

 

Checked my gauge today.

4600 miles since it was filled and it has 3 of the LED's off (above the 1/2 mark there is still one lit -- book says it will hold 2 gallons after the next one goes out)

iDash reports the level bouncing around 48-51%.  (I'm expecting the next LED to turn off soon)

 

Regens on this 3.0 are much more frequent than the were on the 6.6's I ran.

They are also much shorter duration. 

It's usually somewhere in the 260 - 320 mile range between regens and they are lasting 10 - 13 miles running 2 lane highway speeds. 

 

 

Having said all that I'm not sure the def display is super accurate -- I'd expect it to have a least a couple of LED's turned off by now.

Unless it's working really hard and using lots of fuel, it also be surprised if it needs def at 3000 miles. 

 

I'm expecting somewhere around 9000 miles til it tells me it's empty. 

Current plan is to run til it's empty and it starts giving the ' xx miles til speed limit' warnings. 

 

 

 

 

 

 

 

 

 

bonzman17 Enthusiast

bonzman17

Posted
  • Author
Posted

Thanks for the reply. I’m honestly waiting for the speed warning to come on at some point since there’s been zero change on the level. Wish they would put some kind of indicator while in regen.

steve841 Enthusiast

steve841

Posted
Posted (edited)

I wouldnt lose sleep.  Maybe you'll find the "fix" for needing to add def ... 🤣

 

Worst case, you'll get the 55mph warning and you'll know a trip to the dealer is in order.

Edited by steve841
Sqrls Enthusiast

Sqrls

Posted
Posted

2.5 gallons of DEF averages me around 3500-4500 miles. My first tank of DEF was used in 6400 miles, but my def use has slightly gone down. I have 35,000 miles on it already. I normally always have at least 1,000 lbs in the bed with mixed city/hwy driving and pull a trailer pretty often. Normally, I just add 2.5 gallons when it gives me 500 mile warning and it lasts 3500-4500 miles. 2.5 gallons from empty takes me 1-2 bars from full even though it’s only half a tank.

bonzman17 Enthusiast

bonzman17

Posted
  • Author
Posted

Thanks. I usually do not have a load. Seems like crystallization would become a problem at that rate no? Just seems like it’s been to long since the level dropped compared to the colorado I had. I’m going to see if obd2 fusion app I used to monitor on the colorado has the pids for the Silverado. 

redwngr Senior Enthusiast

redwngr

Posted
Posted

If the level is detected the same way as in the LML def tank, then it's not a float -- it's a series of pin sensors, and a bunch of software to estimate the level between the sensors as well as to prevent the display from jumping around when the def sloshes. 

 

 

redwngr Senior Enthusiast

redwngr

Posted
Posted
2 hours ago, bonzman17 said:

Thanks. I usually do not have a load. Seems like crystallization would become a problem at that rate no? Just seems like it’s been to long since the level dropped compared to the colorado I had. I’m going to see if obd2 fusion app I used to monitor on the colorado has the pids for the Silverado. 

I don't think crystallization inside the tank is going to be an issue.

 

Imho, wait for the 1000 mile to empty warning, and/or the 300 mile to empty warnings, and then add some.

The countdown for speed limiting doesn't start till it's reaches empty -- and the first warning is 500 miles to 65 mph. Lots of time from the first 1000 mile to empty warning to get def.

 

 

When I ran an LML my location didn't have a convenient bulk def nearby.

Most others reported that the tank would hold 2 of the 2.5 gallons jugs when the truck gave the 300 mile warning. Mine wouldn't take all of the second jug.  Meant managing a part jug and remember to later add the balance of the second jug later. 

Switching to buying/adding one jug at a time made it simpler.  Did that for a bunch of years without 'crystallization' from a part full tank.

 

 

 

  • 2 months later...
Ross McKenrick New Member

Ross McKenrick

Posted
Posted

I think this is a software problem. I work for Microsoft and I just bought a new 2022 Chevy Silverado 1500 with a 3L diesel engine. We are on our initial cross-country trip towing a 4000 lb RV trailer. With 2500 miles on the speedometer, we have been through 5 2.5 gal bottles of DEF (in addition to what was in the truck when we pulled it off the lot). 
 

With a 5 gal DEF tank, I expected to be able to empty at least a 2.5 gal bottle of DEF into the tank when the tank was approaching empty. But no. Like the previous person, when the gauge says the DEF tank is empty, I am only able to add 2 gal of DEF before it overflows and makes a mess. 
 

I am completely confused by the message that says DEF empty and I have 500 miles before I am speed limited. 
 

I am convinced that the DEF tank is not empty, but I do have 500 mikes of range left. Yet I have to endure this dire message which takes over the dashboard screen for some 20 miles or so and then goes away. 
 

Meanwhile, the DEF level screen has only two readings, 7/8 full and empty. 
 

We need a software update. We need a better user experience so that we can live with this DEF system. 

  • 6 months later...
aangulo1 New Member

aangulo1

Posted
Posted

I have a 2021 GMC Elevation DURAMAX 3.0..... Around 7K on it.... After all being okay, suddenly the DEF gauge started to act weird. It happened after it gave me a low warning. After that and before putting DEF in it, the gauge showed half tank. Decided to fill one jug (2.5 gal), did not move........ After several miles now it was showing full!! Very frustrating. Decided to put the other 2.5 gal in it. It has been 2k miles and still showing full...... Took it to dealership and this is their response: "NO PROBLEMS FOUND, CONDITION IS NORMAL; DEF CONSUMPTION DEPENDS ON ENGINE LOAD, FUEL USAGE, HUMIDITY TEMPERATURE AND IS NOT MILAGE BASED. DEF SYSTEM WARNING WILL APPEAR SHOULD AN ERROR OCCUR"

 

So how is it that before, that DEF gauge will show different levels as the miles grown and now is not? Is GM Tech just giving me some quick response so to not troubleshoot the fault?

 

Thanks

eckseleven Enthusiast

eckseleven

Posted
Posted

The thing with the DEF gauge is that you have to think about it like the "miles to empty" that we have with fuel. It is purely an estimate and that estimate will change based on usage. If your vehicle usage changes suddenly, it takes time for the gauge to reflect that.

 

For me it hasn't been a concern so far. When I'm towing I'l just note what it predicts I have left and pack a jug accordingly. You start to get a feel for it after a while.

  • 2 months later...
gobbledott New Member

gobbledott

Posted
Posted

I am new to def but similar problems.  Mine was filled by the dealer and only showed about 1/3 on the vertical scale and showing def ok.  First warning came showing 525 miles left, followed by one at 225 miles showing def low.  Gauge never moved.  Put in 2 1/2 gal.  still no movement.  Talked to the dealership and the guy tried to convince me that there was no  gauge there.  I will be dropping in to see him in person.  Anyone with a similar problem ?  2019 Silverado, duramax diesel

  • 10 months later...
Ckhris Enthusiast

Ckhris

Posted
Posted
On 7/18/2021 at 10:37 PM, Ross McKenrick said:

I think this is a software problem. I work for Microsoft and I just bought a new 2022 Chevy Silverado 1500 with a 3L diesel engine. We are on our initial cross-country trip towing a 4000 lb RV trailer. With 2500 miles on the speedometer, we have been through 5 2.5 gal bottles of DEF (in addition to what was in the truck when we pulled it off the lot). 
 

With a 5 gal DEF tank, I expected to be able to empty at least a 2.5 gal bottle of DEF into the tank when the tank was approaching empty. But no. Like the previous person, when the gauge says the DEF tank is empty, I am only able to add 2 gal of DEF before it overflows and makes a mess. 
 

I am completely confused by the message that says DEF empty and I have 500 miles before I am speed limited. 
 

I am convinced that the DEF tank is not empty, but I do have 500 mikes of range left. Yet I have to endure this dire message which takes over the dashboard screen for some 20 miles or so and then goes away. 
 

Meanwhile, the DEF level screen has only two readings, 7/8 full and empty. 
 

We need a software update. We need a better user experience so that we can live with this DEF system. 

 

LOL, you work for Microsoft so that is supposed to make us believe you are an expert on GM coding… give me a break… no one cares where you work
 

 

 

SPASierra Enthusiast

SPASierra

Posted
Posted
18 hours ago, Ckhris said:

 

LOL, you work for Microsoft so that is supposed to make us believe you are an expert on GM coding… give me a break… no one cares where you work
 

 

 

You replied with that $htty remark to a post from 2021?!  You must be really bored.  Be a better human.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,949
    Total Members
    8,960
    Most Online
    Gkistler
    Newest Member
    Gkistler
    Joined

  • Who's Online   4 Members, 0 Anonymous, 877 Guests (See full list)

  • Latest Articles

  • Posts

    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • PunchT37
      Parking Brake - Automatic Engagement Questions

      By PunchT37 · Posted

      I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...