Jump to content

Dash camera and rear cam suggestions.

Liquid Plumber AT4
 Share

Recommended Posts

Liquid Plumber AT4 Enthusiast

Liquid Plumber AT4

Posted
Posted (edited)

Any suggestions on a decent model dash cam and possible rear camera suggestion for recording.  I'm looking for a model that can also record when the truck is parked and not in use for recording a potential break in or damage to the truck in a parking lot. Are there any cameras that are any good? Any brand and model suggestions are appreciated. Thank you.

Edited by Liquid Plumber AT4
Transient Senior Enthusiast

Transient

Posted
Posted

I have the thinkware kit from GM Accessories.  However, it looks like you want something like sentry mode on the Teslas.  I don't believe that's an option, and only Tesla has it. 

Liquid Plumber AT4 Enthusiast

Liquid Plumber AT4

Posted
  • Author
Posted
23 hours ago, Transient said:

I have the thinkware kit from GM Accessories.  However, it looks like you want something like sentry mode on the Teslas.  I don't believe that's an option, and only Tesla has it. 

Thank you 

Liquid Plumber AT4 Enthusiast

Liquid Plumber AT4

Posted
  • Author
Posted (edited)
On 8/9/2021 at 12:30 PM, Transient said:

I have the thinkware kit from GM Accessories.  However, it looks like you want something like sentry mode on the Teslas.  I don't believe that's an option, and only Tesla has it. 

Did you get the thinkware standard or premium model??. Looks like on both models it will record while the vehicle is parked and off for vandalism? Does the thinkware kit record the rear to? And last....does it require a wire harness....or is it plug and play? Thank you again.

Edited by Liquid Plumber AT4
It's Tim Senior Enthusiast

It's Tim

Posted
Posted
On 8/7/2021 at 3:07 PM, Liquid Plumber AT4 said:

I'm looking for a model that can record when the truck is parked and not in use also for recording a potential break in or damage to truck in a parking lot. 

You may want to consider moving if these things are that much of a concern.

  • Like 1
  • Sad 1
Liquid Plumber AT4 Enthusiast

Liquid Plumber AT4

Posted
  • Author
Posted (edited)
1 hour ago, It's Tim said:

You may want to consider moving if these things are that much of a concern.

Thanks for the advice there Tim.....you sound fun.

I actually live in a gated luxury apartment complex.....but shi* can happen anywhere, heck....maybe even in your neighborhood to. I own a Plumbing and Heating company and wanted to try a dash cam on my new personal truck before installing them on the fleet. But thanks for your deep concern for my safety bub.

Edited by Liquid Plumber AT4
  • Like 5
Rob Mugs Enthusiast

Rob Mugs

Posted
Posted (edited)

I would not recommend the GM.  You want 4k (8mp) .. 

 

Now, the Viofo A129 Pro has a great picture but the rear cam messes with your TPMS.  So, it's only good for the front.  

 

For that reason, I'd recommend the Blackvue DR900X if you need front and rear.  If you can live without the rear, the Viofo is a damned great camera for the buck.  

 

 

 

 

 

 

Edited by Rob Mugs
Liquid Plumber AT4 Enthusiast

Liquid Plumber AT4

Posted
  • Author
Posted (edited)
4 hours ago, Rob Mugs said:

I would not recommend the GM.  You want 4k (8mp) .. 

 

Now, the Viofo A129 Pro has a great picture but the rear cam messes with your TPMS.  So, it's only good for the front.  

 

For that reason, I'd recommend the Blackvue DR900X if you need front and rear.  If you can live without the rear, the Viofo is a damned great camera for the buck.  

 

 

 

 

 

 

Thank you sir.....I appreciate the recommendation.

 

But according to It's Tim.....if we need dash cam we should just relocate....lol.

Edited by Liquid Plumber AT4
  • Like 1
  • Thanks 1
  • Haha 1
Qwerty143 Enthusiast

Qwerty143

Posted
Posted
5 hours ago, Liquid Plumber AT4 said:

Thanks for the advice there Tim.....you sound fun.

I actually live in a gated luxury apartment complex.....but shi* can happen anywhere, heck....maybe even in your neighborhood to. I own a Plumbing and Heating company and wanted to try a dash cam on my new personal truck before installing them on the fleet. But thanks for your deep concern for my safety bub.

Great response!

  • Like 4
Rob Mugs Enthusiast

Rob Mugs

Posted
Posted
3 hours ago, LamboTexas said:

Great response!

I was going to suggest a turret with a Barrett Model 82 since it's obvious he lives in a real rough part of town... but decided that might be against his complex's rules.

  • Like 3
Liquid Plumber AT4 Enthusiast

Liquid Plumber AT4

Posted
  • Author
Posted
36 minutes ago, Rob Mugs said:

I was going to suggest a turret with a Barrett Model 82 since it's obvious he lives in a real rough part of town... but decided that might be against his complex's rules.

Lol! I am on the top 4th floor. That Barrett 82 is savage, I like the Sig Sauer 716. The complex is full of white collar pencil pushers.....very rough crowd. 😁

  • Like 1
Transient Senior Enthusiast

Transient

Posted
Posted
23 hours ago, Liquid Plumber AT4 said:

Did you get the thinkware standard or premium model??. Looks like on both models it will record while the vehicle is parked and off for vandalism? Does the thinkware kit record the rear to? And last....does it require a wire harness....or is it plug and play? Thank you again.

The kit comes with everything needed for install.  It's a wired setup.  I have the premium that has both front and rear cameras.  It connects to my phone via Bluetooth for downloading videos.  Good quality audio and video.  I got the camera setup when I bought my truck because I knew I was moving to California.

Transient Senior Enthusiast

Transient

Posted
Posted
13 hours ago, Liquid Plumber AT4 said:

Lol! I am on the top 4th floor. That Barrett 82 is savage, I like the Sig Sauer 716. The complex is full of white collar pencil pushers.....very rough crowd. 😁

Now we're talking my language.  I'm more of a M2 fan. 

Liquid Plumber AT4 Enthusiast

Liquid Plumber AT4

Posted
  • Author
Posted
On 8/10/2021 at 1:50 PM, Rob Mugs said:

I would not recommend the GM.  You want 4k (8mp) .. 

 

Now, the Viofo A129 Pro has a great picture but the rear cam messes with your TPMS.  So, it's only good for the front.  

 

For that reason, I'd recommend the Blackvue DR900X if you need front and rear.  If you can live without the rear, the Viofo is a damned great camera for the buck.  

 

 

 

 

 

 

Thanks again Rob.....just ordered the bkackvue dr900x 2 channel camera. Looks like a great setup. Question, where did you mount your rear camera? And what mounts or accesories did you buy? Also, did you tap into fuse panel with fuse tap kit? I noticed it's a 2 prong fuse tap kit, but my 2021 1500 AT4 has 3 prong fuses, curious on what you did. Thanks again. 

Rob Mugs Enthusiast

Rob Mugs

Posted
Posted
On 8/18/2021 at 4:52 PM, Liquid Plumber AT4 said:

Thanks again Rob.....just ordered the bkackvue dr900x 2 channel camera. Looks like a great setup. Question, where did you mount your rear camera? And what mounts or accesories did you buy? Also, did you tap into fuse panel with fuse tap kit? I noticed it's a 2 prong fuse tap kit, but my 2021 1500 AT4 has 3 prong fuses, curious on what you did. Thanks again. 

 

Apologize for not seeing this till now.  I am an unfortunate one with a Viofo but I have seen the quality of the Blackvue in person and why I recommended it over the Viofo.  

 

Everything looks pretty similar.  Adhesive to mount to the windows (make sure you stay OFF the defogger wires) and from their page, looks like nothing additional needed.  You'll need a constant and switched power.  I'm in bed so can't look at which fuses I used but if I recall correctly, I found a couple double blade spots for them.  A bit of searching on here should net you the same results I found

 

 

 

 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Grumpy Bear
      Sugar Bears 2015 GMC Terrain SLE-2 2.4 AWD

      By Grumpy Bear · Posted

      286,740 Mile Services   8/6/2026   New AC Compressor. Refrigerant oil and dye, evacuate and charge system.  New exhaust system from cat back.  New Iridium plugs plus replace #3 coil Repair/rewire headlamp wiring (passenger side) and replace all forward bulbs. Polish lenses of both assemblies.  Pull rear rotors, clean and adjust parking assembly. Inspect, clean and grease front calipers. Check pads and shoes.  4 wheel power bleed of brake system. Dot 4 Reset idle speed 50 rpm higher New Serpentine belt.    Will need new pads in the rear in about 5K more miles.    Tax Title and License out the door just short of a grand.    AC clutch had bitten the dust. 1 year warranty on the pick and save replacement. Thing will make a Polar Bear cry Uncle.  He spent quite some time on the wiring. It was in the harness and he does nothing half. I got off cheap. I have considerable more light down the road. Sylvania Silver Star replacements.  Gas seal between the porcelain and shell of plug #3 was blown, cooked the coil. That was the cold miss.  Love the new exhaust. I can sneak into the neighborhood again.  Nice to have a working parking brake again. Belle Tire never got it done. That was disappointing.    This was one of her bigger bills and still way cheaper than a payment even given the oil consumption. This thing cost me under a hundred a month in repairs and normal routine costs. What is my incentive to replace it? 🤔           
    • AidenVorpagel
      cam upgrade in CA

      By AidenVorpagel · Posted

      hello I recently bought a 2012 gmc 1500 with a 5.3 and have a AFM disabler on it I'm interested in doing a cam but I'm worried if I remove the AFM system I will fail smog does anyone have info if they are able to detect that or a work around to it (not talking about hot smogging) please let me know thank you  
    • B14Sierra
      Noise after AFM delete

      By B14Sierra · Posted

      Did you figure it out?
    • B14Sierra
      Possible lifter tick after DOD delete

      By B14Sierra · Posted

      Update. I started chasing down my symptoms. Started first with pulling valve covers and looked at everything. Everything looked good and couldn't hear or feel anything different. Then a compression test. 240 psi or really close on each cylinder. I was worried I was a tooth off of timing. Not bad for an engine with 173,000. Granted I did put new heads on. I sprayed water around the injector area to see if I could hear a change. Nothing. I hooked up my new hp tuner which I should have done in the first place but I don't really know what I'm looking at just yet but am learning. I noticed the fuel trims were way off so that told me I have to have either a bad injector or exhaust leak. New injectors, so I did the shop vac on blower and in the tail pipe. Sprayed soapy water and found the exhaust flange on the drivers side was leaking. I didn't think it would be that considereding I pulled the heads and left the manifolds attached. I did have the transmission replaced not long ago. They must have not seated them properly but I guess I didn't notice. I put in new gaskets on both sides. Which by the way isn't a bad job but I had a hard time getting them to seal right. Took two attempts. Reset the fuel trims and the ticking is gone, engine runs smooth and acceleration has improved. Got to feel the real difference with that stage 1 cam. It's not that big of a difference but it does add a little more. It feels like how the truck should have been from the factory.
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      Can it still be Assembled I?    Stribeck says that we need a certain amount of viscosity under conditions of load and velocity to prevent two surfaces of a know roughness from tearing each other asunder. And we have marketing trying to tell the masses that those two surfaced require less of that commodity due to more exact limits being placed on the same old clearances. We also know that there are limits to how hard something can before it becomes to brittle to be viable and to smooth to 'wet' the surface and that both of those conditions have been known and met since about the Second World War.    That viscosity value shook out at 10 centistokes at 212 F just under a hundred years ago.  Give this a look: [Anton Parr]     What is advertised is the Kinematic viscosity (mm2/s) or that which has been density adjusted but the value we are after is the dynamic viscosity (mPa.s) or true viscosity. You can see that this number is dependent on density thus base stock and temperature. You can also see that an SAE 30 doesn't reach that value in this example. However an SAE 30 that is at the upper end of the SAE 30 range; 12.5 cSt (mm2/s), might. 12.5 * .83 = 10.375 (mm2/s). If you could find an SAE 30 at the upper end these days.   Then there is the complication of viscosity modifiers or VII or VM, whatever you wish to call them. Polymers added to very thin base oils, perhaps 3 to 6 cP oils, that will meet the SAE *W30 spec at 'tested' shear rates and 100 C/212F  target temperature. So a polymer fortified base that is a fraction of the 10 cP requirement Stribeck insist upon.   This could be all well and good if those polymers didn't have two very problematic 'features'. They shear or loose viscosity both 1.) permanently and 2.) temporality. And they do both omitted in the advertised data with the distinct  purpose of deceiving the consumer of the actual operating state of the fluid. I've shown the example of Warren Oils COSTCO 10.91 cSt 5W30 formuation several times where the 100 C HTHS value is 6.9 cP!! That's the temporary shear down and with and SSI or shear stability index of 9.4 cSt. Note the intentional deception in using mixed units?    After a short while that 9.4 cSt oil has a viscosity corrected dynamic value of 7.8 cP. But as the SSI is still within the range of an SAE *W30 whose lower value is 9.3 cSt.    This allows them to continue to call this SAE 16 weight oil a 30 weight, the cake, and still meet the API requirements for fuel efficiency IMPROVEMENT mandated by the EPA. The eating of the cake. By the time you've worn out your motor doing the responsible thing by adhering to the warranty requirements, (the stick), you get deprived of the carrot, wear control. So sad, to bad.   So what can be done? Do I need actually say? [Anton Parr]       Even this must be monitored if the oil is on the low side and the VII an organic or you opt for a 0W40 with an even lighter base oil and more / higher MW VII. (Note the lower density of the 40 weight versus the SAE 30 mono-weight?)    There is another workaround. Temperature. An SAE *W30 run at a bulk temperature of between 180 and 195 F.    Being the belt and suspenders sort I am I do both. Run it cook and run it heavy.    In Part II I'll work the AW package. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...