Jump to content

Fog lights

Eugene Sanchez
 Share

Recommended Posts

Eugene Sanchez New Member

Eugene Sanchez

Posted
Posted

I have 2021 Hd 2500 custom 4x4 Looking for some information about the wiring harness I found a wiring harness by where the fog lights are just wondering if it’s it Any help much appreciated thank you

0DDE4F1E-8291-44B7-AAAE-79C8D866FA50.jpeg

5D7202CC-6779-4685-9D4D-ECE2AFE854B6.jpeg

88ACAF29-9000-442D-AABF-9108B6692993.jpeg

  • 3 weeks later...
shadow gray 2020 hd Enthusiast

shadow gray 2020 hd

Posted
Posted

Harness for the fog lights is tied into the harness with the front sensors, if you have front parking sensors.  It is a one in all harness and splits at the bumper where each fog light would go in the bumper.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Grumpy Bear
      Sugar Bears 2015 GMC Terrain SLE-2 2.4 AWD

      By Grumpy Bear · Posted

      I'm suborn like that Ed. There's a plaque in my doctor office that says, "Don't quit, take a break." Works for allot of things.    Reality is, the wife loves her SUV and even given it's issues, she'd buy another if she found one with low enough miles. Then again she has me to maintain it.    Most of what ails this thing is GM shooting themselves in the foot and by extension the buyer. Besides a ridiculous breather system the cat warm up strategy, IMHO, is the dumbest thing I've ever seen an OEM do to a vehicle they warranty. On cold start it r-e-t-a-r-d-s the ignition to like -17* ATDC and dump fuel like kicking over a pail to force combustion in the CAT's for rapid warm up. This literally hoses the oil off cylinder walls and creates enough varnish precursors to stick rings in even well maintained engines. THEN if that wasn't bad enough they recommend using a wanting fluid specification at equally stupid interval.    Common to all GDI motors I'm aware of is this silly practice of driving the HPFP off the cam giving a leaking pump direct and unchecked access to the crankcase. And sir, eventually the ALL leak. Your job is to "catch it if you can". Yes, these are the same people that removed dipsticks from engines and transmissions in belief Joe Average wasn't capable of checking, reading and maintain his own vehicles fluids. Sadly  and in large they were correct. Most people these days can't tell a sparkplug from a fire plug.  Great ideas one and all.    Every move and every error calculated to defend themselves from the law and their own customers.       
    • Fishindude
      Dash Mat

      By Fishindude · Posted

      Most online suppliers and Amazon. All have noted "not for use with Bose speakers".
    • Coastie05
      Sugar Bears 2015 GMC Terrain SLE-2 2.4 AWD

      By Coastie05 · Posted

      Very interesting thread. Definitely didn’t expect to see this kind of mileage out of that engine. 
    • Grumpy Bear
      J&L OIL SEPARATOR CO

      By Grumpy Bear · Posted

      Just did an injector/HPFP replacement on Pepper at 192,400 miles; close enough to 200K, RIGHT? (If 200K is considered life end and to me it isn't). But hey, to each his own.    Have never run a catch can on this vehicle. Back side of every valve looked like a new valve spray painted semigloss black. Port walls looked 'neat' (all a normal result of passive EGR via VVT) Zero build up even in AFM cylinders. Just color. It uses no measurable oil and never has.    At 155,000 I put her on E-85 and a borescope of the cylinders at plug change showed very clean pistons and valve faces. The replaced injector tips looked new. (It was the pump piston seal that was leaking). Oh well, have six good backups.    Still gets 28 mpg on gas (highway average) and over 20 (highway) on alky. UOA's look good and runs as good now as it did when I bought it. Better in fact.    What improvement would a Catch Can provide this motor?     And given all this I expect that IF I installed one I'd see some water/gas/oil vapor accumulation. Byproducts of normal combustion.   Having said that, IF my motor used an appreciable amount of oil I'd consider it a useful 'crutch' until I had the situation corrected OR if bore polished, until I junked it or rebuilt it to stave off repeated plug fouling.    I'm not telling you what I THINK. But what its DONE.          
    • Grumpy Bear
      Starting a new thread regarding mounting my 2014 OEM wheels to my 2026

      By Grumpy Bear · Posted

      Love the look. I'm a SCSB lover myself.    Two items. 1.) A spacer changes scrub radius but this also changes when we use wheels of different offsets. A little isn't a big deal. 2.) Steel wheels, alloy wheels all have different thickness. Same effect on the stud and lug nut as a spacer. When hub centric the wheel isn't supported by the stud. It's supported by the hub. The stud just keeps it all together.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...