Jump to content

Kooks y pipe problems

m1c

By m1c
in Engines & Drivetrain

 Share

Recommended Posts

m1c Enthusiast

m1c

Posted
Posted

I have a 2018 Sierra RCSB 5.3, 4x4 that I added Kooks 1-7/8 long tube headers and green catted y pipe too. I'm having trouble with the y pipe reaching the Borla ATAK catback. It seems to be a couple inches too short. Has anyone else had this issue?

ftwhite Enthusiast

ftwhite

Posted
Posted

I had a similar problem getting the kooks ypipe to connect. The ball joint just wouldn't tighten up enough to close the gap and not leak. I had a muffler shop weld on a flange joint instead. Not as flexible, but there is another flex point downstream, and no problems over 10k miles so far.

20220501_080551.jpg

  • Like 1
3tspapat Enthusiast

3tspapat

Posted
Posted

Longer exhaust hangers/bushings should should allow you to move the catback frontwards enough to get it to fit.

  • Like 1
M1ck3y Senior Enthusiast

M1ck3y

Posted
Posted (edited)

Yup, I have that problem. I contacted kooks and my understanding is that I have over tightened the y-pipe to header connections.

 

I've been meaning to take a rubber mallet to the y-pipe to break the connection (ball/socket joint). Bolt up the cat back first and then "snug" it back up to the headers. Ball/socket connection doesn't need much torque (just enough to hold it in place); heat from the exhaust will do the rest.

Edited by M1ck3y
m1c Enthusiast

m1c

Posted
  • Author
Posted

Thanks, for the suggestion.

 

My y pipe was nearly 3" short. I slid the mid-pipe from the catback forward and had to pull it out of the hangar to reach. It's a little jury rigged at the moment. I was working with Kook's tech support, but they turned me over to the CEO who suggested cutting it up and putting a 3" wide clamp there. Not thrilled about that, but not bashing them either.  I think I've decided to put a resonator there before the muffler anyway to cut back on the sound.

  • Like 1
m1c Enthusiast

m1c

Posted
  • Author
Posted

My y pipe was that short before i even snugged up the ball joints to the headers. I'm a little disappointed in the customer service for such a premium priced product thus far.

  • Like 1
M1ck3y Senior Enthusiast

M1ck3y

Posted
Posted (edited)

Yeah I hear you, I'm just quoting what Kooks said to me; Mine might be just as short as your's is. I ended up jamming a 2x6 bewteen the axle and the muffler to force it forward and bolt it up 😜

 

I have a borla 40004s muffler I might try and fit in there. 

 

In hindsight I should have gone with ARH.

Edited by M1ck3y
m1c Enthusiast

m1c

Posted
  • Author
Posted

I tried ratchet strapping it together from the exhaust mount to the transmission support, but I didn't like it pulling the exhaust tips under the truck. 

 

The worst part is it caused me to cancel my date with the tuner, and now I can't get on the schedule for 2-3 weeks. 

m1c Enthusiast

m1c

Posted
  • Author
Posted

Now it sounds like something is loose in the drivers side greencat. Metallic rattling noise... any ideas? Thanks!

M1ck3y Senior Enthusiast

M1ck3y

Posted
Posted
3 hours ago, m1c said:

Now it sounds like something is loose in the drivers side greencat. Metallic rattling noise... any ideas? Thanks!

 

I know on mine when the exhaust is cold the clamp's at the ball/socket joint will sit loose, and can make noise if you hit on it. Other than that... it could be the substrate is loose in the cat :dunno:

m1c Enthusiast

m1c

Posted
  • Author
Posted

The rattle is definitely coming from the cats (now both sides). I have checked for loose connections and anything touching the headers. I can stop the rattle by touching something to the cats while it's rattling. Touching anywhere along the headers and primaries has no effect. Sent a video to Kooks at their request this was what they said to check. 

 

Regarding the y pipe, I'm exceptionally disappointed in the craftsmanship and customer service of Kooks. I received no other responses from them on these issues. I slid the mid pipe forward and removed it from the hanger mount just so the ball and socket would seat well enough to clamp together. I decided to have the y pipe and the mid-pipe to the cat back cut and a Vibrant resonator welded in place. I can't believe how much of a difference the resonator made on the sound of the headers! Love the sound of this combination. 

 

Thanks all for your help!

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      MPG at 600 miles

      By Chuck FB · Posted

      I would have to read back to get a better picture in my mind of some of the other comments and what they were using for a driving scenario they based the fuel mileage off of. That is why the fuel mileage conversation is extremely difficult to make fair comparisons from. If I was to be living in town and only driving around town, light to light and some longer stretches that doesn't have a light every block, and the usual stop at a grocery store and the bank and so on and so forth, my fuel mileage even during the summer time would be so bad with my truck I don't even want to know how bad it would be !. Then add in winter time and idling to warm it up to clear the windows and driving through snowy streets etc, large heavy trucks with gas engines have NEVER been worth crap for fuel mileage and why some little pot licker of a car with wheelbarrow tires and a 1300 cc four cylinder non turbo engine was the ticket to using a mere fraction of the fuel over a full size pickup.    By the way my truck has the 34" tires as its a HC but not the BFG KO3 tires ( that was an option for my truck but the sales guy couldn't figure out what the tires actually were so that never got on the order until it was too late to change the truck order ). So what fuel mileage your getting actually sounds good for "town driving" and with my truck when I go to town the fuel mileage keeps increasing as I get closer to town because it takes quite a while to get the driveline oils warmed up ( and why it always shows better fuel mileage on the return trip from town because its already warmed up ) but once I am in town that fuel mileage average just keeps dropping the more I mess around town and then has to recover back to something reasonable again by the time I get home for an over all average.    I'd be curious what your sticker says for the factory weight of your truck, mine is close around that 7700 lb due to the options it has. But anyway the long and short is, vehicle weight, higher rolling resistance heavy tires and a hefty driveline and a relatively large gas engine make for crap fuel mileage in stop and go scenarios, all one can do is drive it easy off the line at each stop and as my dad had said over the years, drive like a raw egg is under your foot and that's the best one can do. Years back with a carbed engine and if the carb was getting a bit out of tune etc as would the ignition system, the fuel mileage on pickups with larger engines was just awful compared to what your getting. We pay the fuel price penalty for driving HD trucks over some little vehicle, that is the reality. 
    • diyer2
      Navigating senior years.

      By diyer2 · Posted

      Speedy recovery.
    • KARNUT
      Slate Electric Truck

      By KARNUT · Posted

      We had two Toyota’s with that engine in the mid 80s. We had 50 gallon fuel tanks, a toolbox full of tools, an air compressor and assorted parts for our equipment. We beat those up and down pipeline ROWs until we started buying diesel trucks. Then they became parts runners and first vehicles for our teenagers first cars. Our shop Forman wrecked them both two years apart when we hired him out of high school as an apprentice. Good thing he’s an excellent mechanic. It took awhile before he could be called a good driver.
    • diyer2
      Gas Prices

      By diyer2 · Posted

      $4.26 85 oct 
    • William Aldrich
      Bent valve in 2025 GMC Canyon Denali - Requires engine swap at 14K miles

      By William Aldrich · Posted

      I have a 2025 GMC Canyon Denali.   On a trip recently the engine failed.  The dealership diagnosed a bent valve and says there is a service bulletin that indicates to 'relace the engine'.  The truck only has about 14K miles and is under warranty.   The failure occurred 5/11/2026.   So far I have worked with GM Customer Assistance and Roadside Assistance.  Evidently no engines are available and nobody will offer a date when a new one will be.   Coming up on two months with no repair or timeline and no loaner from the dealership.   GMC Customer Assistance is 'ghosting' me and keeps closing the cases I've opened with no resolution.   Hoping someone can help me on how to escalate this issue.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...