Jump to content

AEV Bison Bumper

TeamNotYou
 Share

Recommended Posts

newdude Senior Enthusiast

newdude

Posted
Posted

No idea but from having seen one in person you'd need quite a bit of parts, not just the bumper.  

 

The bumper, impact bar behind it, plus the front fender extensions as well since everything under the headlights is different from a regular Silverado.  

  • 1 year later...
Transient Senior Enthusiast

Transient

Posted
Posted (edited)

I've been looking into this and found 1 issue that would prevent the AEV front bumper from being used on the 2019-22 trucks.  Where the turn signals are located in these trucks, there is a foot step in the bumper.  It may be possible for a modification to retain the turn signals and eliminate the foot step holes on the bumper.  After all, the Sierra AT4X doesn't have the same top of the bumper with the foot steps, so I wonder if they're plastic inserts like the regular rear bumpers on our trucks.  I haven't been able to get close to a vehicle with these bumpers, but I have been doing a bunch of research on this conversion.  Yes, there's a bunch of unique pieces we'd need to purchase for the front bumper, but anything is possible with enough patience. 

 

AEV is now selling all the skid plates (except for the front skid plate at the front bumper) and rear bumper on their website.  It's possible that with a little time they may choose to sell the front bumper, too.

 

I've looked into doing the conversion on my truck (2020 Trail Boss LT), but it's going to be expensive.  AEV wants $3,000 just for the rear bumper, not including the Baja Designs lights and brackets.  That's more expensive than the ZR2 suspension upgrade kit from GM Performance.  If you got all the pieces for the front and rear bumper, plus all the skid plates including the front skid plate via the dealership, you're into this project for the cost a supercharger kit professionally installed. 

Edited by Transient

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • SwitchBladeSierra
      HELP! DUMPING COOLANT

      By SwitchBladeSierra · Posted

      If anyone lands here looking for an update - the problem wasnt with the hose, the clamp, etc... I purchased a metal Thermostat housing that just must not of been made to spec. It just wouldn't plug up the hose.. Went back to a plastic cheap housing - leak fixed. Some plumbers tape carefully placed in tandem with a clamp likely would've gotten the job done.   Best,
    • SwitchBladeSierra
      AUX switch install

      By SwitchBladeSierra · Posted

      For anyone following, this is what I have deduced from this forum - and my very specific niche case. Please do let me know if you see me going in the wrong direction here. For context, I have a 16 sierra 1500 w/t. Has TC and Cargo light switches. Removed the switch to find the X1 and X2 of the S48A connection populated with wires (x1 10-14, and x2 1-5).   Took photos of the X61A-X5 to find the wires from S48A-X1 land here at their respective pins (10, 11, 17, 23 on the X5). Was hopeful that this means my X51A fuse box has the appropriate pins... No cigar. So now I will be routing wires from the rear of the X61A-X1 to the engine bay and to their respective negative relay triggers. Please see to the diagram. If any has insight as to where the S48A-X2 pins 4 and 5 land that would be awesome.   Note: please disregard fuse sizes. Main fuse will like be 25A, all mini bus fuses will likely be 10-15A   Cheers
    • Grumpy Bear
      Sugar Bears 2015 GMC Terrain SLE-2 2.4 AWD

      By Grumpy Bear · Posted

      287,500 Mile Service   8/13/2026   Reset Fuel Trims   Since the work done in the previous post there was a good improvement in response in all areas except right after a fill up where the LTFT would go -20%+ for about four miles while the STFT was near neutral. Before the work they both went very negative for a few miles after a fill up but act normal thereafter.    We did a systems check of the vapor recovery system for functionality and ability to hold a vacuum. That checked out fine. But this doesn't mean the charcoal canister is dead in the water. Testing that is next up. For now the reset of the fuel trims.    I intentionally shorted the fill exactly two gallons to eliminate any chance of filling the canister. On start up the trims were behaving normally until I got up and rolling where the LTFT went -10 / -11%% but the short was + 2 to 0%. Within a mile the the STFT offset the LTFT and by 2 miles they were neutral. HUGE improvement but still not hunky-dory.    I'll watch them for a few days. Perhaps another tank where I will fill completely to 'first click' and compare. Meanwhile on the hunt for a new canister and I'll toss another purge value at it for good measure. Pending the outcome of the canister test that is. Progress of any kind is welcome.    Fuel economy improvement with bringing hole #3 back to the living was a noticeable bump to the positive. Even on the few miles I drove after the refill I already see another bump up by the trims reset.     She's purring like a kitten with a warm bowl of milk.    BTW, adding 50 rpm to the idle took the majority of the negative timing out on cold start up and leaned the cold idle. No longer burbles in the cat. What a dumb way to heat a cat.      
    • OnTheReel
      Post your UOA, (used oil analysis) here

      By OnTheReel · Posted

      Yeah, shame I can’t really get that filter easily anymore. Running a PureOne. Your fave!    TAN would be neat to see. Confirmation I ran it too long probably. 🤣
    • superdave160
      Roll up bed cover experiences

      By superdave160 · Posted

      My son and I both bought new trucks in 2017. Both of us immediately put Truck Covers USA American Roll Covers on our trucks. My son still has his truck and it never sees the inside of a garage. We live in Alabama, so not much snow. My truck was my daily driver and was in the garage when I wasn't driving it or at work. No issues with either cover even after almost 9 years. About a year ago I sold my truck to my brother and bought a 2025 Silverado 2500. The second thing that I put on that truck was a new Truck Covers USA cover. They are very well made and have a very positive locking system. I looked at a Retrax and my concern was the way that the cover locked to the rail. BTW, the first thing I put on the new truck was step bars. Those new trucks are high!

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...