Jump to content

5.3 / 6.2 valve covers / oil burning

mdipasquale20
 Share

Recommended Posts

mdipasquale20 Enthusiast

mdipasquale20

Posted
Posted

All - been a while but wanted to check in. 
 

i have a 17 1500 5.3 with 220k. Oil changed every 3/5/7000 miles. Owned it since new. 
 

dod was tuned out at 75k and motor was out at 145k due to collapsed lifter. Bottom end was left alone - new cam / lifters / dod delete. 
 

I started running 5w30 from 75k to 195k. 
 

To the main issue - around 190k, it started to burn oil.  Currently it’s around a quart per 500 / 600 miles or so. Over the last 6000 oil change - I added 11 quarts lol. 
 

I tired Valvoline restore and protect for 20k miles at 3k intervals with little change. Installed a catch can at 217k and only catch about 3 oz over 3000 miles. 
 

I’ve been running 10w30 for the last 6000 miles. Just did an oil change and stuck with 10w30. 
 

I’ve ordered replacement valve covers.  It seems the numbers have been updated multiple times and the covers are the same as the next version of 5.3/6.2s. 

I’ve only installed the drivers side so far but I wanted to show you my old

cover vs new. Not much difference but it seems the old cover was bypassing the baffles and sucking oil / vapors right into the airbox. 
 

it seems GM changed some of the rivets in the middle of the baffle to maybe hold more pressure on the edges against the cover.  I’m going to drill the rivets so we can see what’s under the baffles. 
 

has anyone dealt with this much oil consumption / valve covers / updated part numbers?

 

thanks all. Really hoping this engine makes it to 400k without touching it again. 

IMG_5677.jpeg

IMG_5676.jpeg

mdipasquale20 Enthusiast

mdipasquale20

Posted
  • Author
Posted

Here’s one more of the new drivers side cover. 
 

will upload pics of the passenger side when I swap them over. 
 

also here’s my passenger side cover when the lifter collapsed at 145k in November of 2022. 
 

IMG_5675.jpeg

IMG_5582.jpeg

rav3 Senior Enthusiast

rav3

Posted
Posted

Have you looked at your brake vacuum pump?

 

 On the 2017 Chevy 5.3L, a failing mechanical brake vacuum pump can cause excess oil consumption. The pump relies on engine oil for lubrication and a seal. If internal seals fail, the pump will draw oil directly out of the crankcase and push it into the brake booster or intake, where it is burned.Key Symptoms of a Failing Vacuum Pump. Hard or stiff brake pedal: Loss of vacuum assist makes braking effort significantly harder.Oil in the vacuum line: Disconnecting the vacuum line to the brake booster will reveal wet oil inside the hose.Noisy operation: A clicking, grinding, or loud tapping sound coming from the front/driver's side of the engine.Smoke from the tailpipe: Burning oil as it cycles through the intake.

  • Like 1
mdipasquale20 Enthusiast

mdipasquale20

Posted
  • Author
Posted

I just deleted the vac pump but there was no oil in the line to the booster and brakes always felt great. Wanted to remove it from the equation before it was an issue.  I installed the two plugs in the oil passages and a block off plate. 
 

there’s a company that makes a vac manifold that goes between the purge valve and the intake. I used that for the booster vac line - I didn’t want to T into my catch can return line. 
 

the vac pump was replaced under warranty back in 2019 or so, so it was the new style pump. 
 

  • Like 1
mdipasquale20 Enthusiast

mdipasquale20

Posted
  • Author
Posted

I don’t care if it stops burning oil. I just need to slow it down.  It’s got 220k. I never missed an oil change. It doesn’t make sense for the oil rings to not do their job - the plugs aren’t caked and my factory cats are still in place and functioning.  
 

I don’t think there’s excessive crankcase pressure from worn compression rings because I don’t get a lot of oil in my catch can between the PCV valve and the intake. 
 

I tore apart the old driver side VC. There’s a sealant between the alum valve cover and steel baffle assembly that’s riveted down.  It seems the seal let go near the port that goes to the intake / before the throttle body. 
 

The design looks like a sealed side that sucks from the air intake and pulls from 3 / 6 holes and then internal baffles seperate the oil / vapors from the air and then drain back down and drip to the heads. 
 

Once that seal fails, oil will be sucked up right into the air intake / before the throttle body. It won’t pass through the separators and you’ll burn more oil. Add in the fact that both valve covers could attribute to this and you may end up with significant consumption, especially when you add in the amount of miles. 
 

I do not have a brand new valve cover to tear apart to see what they changed inside the cover. Part of me wants to waste the $75 but that’s 6 quarts of oil if these fixes don’t work lol. 
 

see pics of drivers side cover pulled apart. 
 


 

 

IMG_5680.jpeg

IMG_5681.jpeg

IMG_5682.jpeg

  • Thanks 1
mdipasquale20 Enthusiast

mdipasquale20

Posted
  • Author
Posted

Did the passenger side today. Seemed worse than the drivers side. I’ll check back in 5000 miles or when the low oil light comes on - whichever comes first. 
 

on another note - went to do sway bar bushings and 3 of 4 bolts broke. Gotta love New England. 
 

 

IMG_5687.jpeg

IMG_5691.jpeg

  • Like 3
  • 4 weeks later...
Jay Ratliff Enthusiast

Jay Ratliff

Posted
Posted

I'm at 315k miles on my L83, dod/afm still operable. It "uses" about 1.5-2qts per 5k miles. I use Valvoline 5w30. I top it off at 2,500 miles between changes I had to replace the valve cover gaskets a while back, the passenger side was leaking and soaked the starter. 

  • Like 1
  • 4 weeks later...
FiLo New Member

FiLo

Posted
Posted

Any update if the new valve cover help with the oil consumption? 
I have a 2014 GMC sierra and my truck is consuming a lot of oil so I’m wondering if replacing the driver side valve cover will stop some of the oil consumption. Thanks 

Grumpy Bear Senior Enthusiast

Grumpy Bear

Posted
Posted
On 5/30/2026 at 8:33 PM, mdipasquale20 said:

All - been a while but wanted to check in. 
 

i have a 17 1500 5.3 with 220k. Oil changed every 3/5/7000 miles. Owned it since new. 
 

dod was tuned out at 75k and motor was out at 145k due to collapsed lifter. Bottom end was left alone - new cam / lifters / dod delete. 
 

I started running 5w30 from 75k to 195k. 
 

To the main issue - around 190k, it started to burn oil.  Currently it’s around a quart per 500 / 600 miles or so. Over the last 6000 oil change - I added 11 quarts lol. 
 

I tired Valvoline restore and protect for 20k miles at 3k intervals with little change. Installed a catch can at 217k and only catch about 3 oz over 3000 miles. 
 

I’ve been running 10w30 for the last 6000 miles. Just did an oil change and stuck with 10w30. 
 

I’ve ordered replacement valve covers.  It seems the numbers have been updated multiple times and the covers are the same as the next version of 5.3/6.2s. 

I’ve only installed the drivers side so far but I wanted to show you my old

cover vs new. Not much difference but it seems the old cover was bypassing the baffles and sucking oil / vapors right into the airbox. 
 

it seems GM changed some of the rivets in the middle of the baffle to maybe hold more pressure on the edges against the cover.  I’m going to drill the rivets so we can see what’s under the baffles. 
 

has anyone dealt with this much oil consumption / valve covers / updated part numbers?

 

thanks all. Really hoping this engine makes it to 400k without touching it again. 

IMG_5677.jpeg

IMG_5676.jpeg

 

Did all this valve cover work slow the oil consumption? 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Another JR
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By Another JR · Posted

      Have considered installing a DC to DC charger in your camper to replace your isolator?  
    • newdude
      Gas fill door

      By newdude · Posted

      Common failure.  You need to replace the fuel door housing.   The painted cover transfers over to the new housing.  To remove the old one there is 4 spots where you poke the plastic to release it.  
    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      I have an observation and a question... 1) I watch the voltage closely because I have had to dial in the cut-in/cut-out voltages of the battery separator to my camper.  The "smart" charging drives me nuts.  Anyway, I noticed that when coasting for a while, and especially if lightly using the brakes (though not necessary), the voltage goes up from mid/high-13 volts to mid/high-14 volts.  Then it drops back down after stopping or going again.  Consistently!   The only explanation I can come up with is REGENERATIVE BRAKING!  Well, maybe that's a little bit of an exaggeration, but it's certainly free extra battery charging.   2) Driving on mountain roads I will use L and vary the max gear.  Things straighten out and I end up in L10.  Sometimes I leave it there for a while.  Is there any difference between L10 and D?   

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...