Jump to content

Steps On My Truck

JRLZ71

Recommended Posts

JRLZ71 Enthusiast

JRLZ71

Posted
Posted

I'm about to put a 3 inch body lift on my truck, and I'm just a little torn between the n-fabs, dominator II steps, or no steps at all. Tell me what you think

SavageNFS Enthusiast

SavageNFS

Posted
Posted

I really like the n-fab steps myself...would look fantastic on your truck. I am looking at them myself, but can't decide if I want the bed access or not. I don't like the look, but want the step.

jblakeney Senior Enthusiast

jblakeney

Posted
Posted

I just put UWS oval steps on my truck last week...... I think the part number is OSB111 I dunno though. But they are quite nice.....

 

I looked at the GM ones.... They require drilling.... I don't want to poke holes in my truck and start rust.... So Aftermarket NO DRILL was in order....

 

Please over look the Dirty Truck..

 

Jbo

post-41100-1280609763_thumb.jpg

post-41100-1280609763_thumb.jpg

post-41100-1280609763_thumb.jpg

post-41100-1280609763_thumb.jpg

MacA Enthusiast

MacA

Posted
Posted

This is definately a personal preference. My preference is no steps at all. HOWEVER, I have a daughter and short wife, so I had to do something. I went with the black N-Fabs because I thought they were the best, less conspicuous option for the money. If you have the money AMP Research makes a hide-away step that folds under the truck when not in use. I just couldn't justify the $2K(?) for them! The Go Rhino is a good product. I was just able to find a good deal locally for my N-Fabs!

 

I looked at the GM ones.... They require drilling.... I don't want to poke holes in my truck and start rust.... So Aftermarket NO DRILL was in order....

That might be the case for your '99 model, but the GM steps for the GMT900 series trucks are a direct bolt-on! I originally bought a set of the GM 6" ovals for my '07. They bolted to factory locations, just a little too big and "noticeable" for my liking!!

 

Good Luck with the decision! :)

nick3941sd Enthusiast

nick3941sd

Posted
Posted

I have TrailFX on my truck. Click on my profile and you can see how they look on a white truck. I got them on sale but idk if they are still on sale. I got them for 146 shipped and love them. I got the part number from TrailFX and searched it under google shop and it brought up all the best prices.

jblakeney Senior Enthusiast

jblakeney

Posted
Posted
I looked at the GM ones.... They require drilling.... I don't want to poke holes in my truck and start rust.... So Aftermarket NO DRILL was in order....

That might be the case for your '99 model, but the GM steps for the GMT900 series trucks are a direct bolt-on! I originally bought a set of the GM 6" ovals for my '07. They bolted to factory locations, just a little to big and "noticeable" for my liking!!

 

Good Luck with the decision! :)

 

 

So, they fixed the problem. and made them bolt on now.

 

Jbo

brad519 Enthusiast

brad519

Posted
Posted

When I checked 4Wheel Online last week they had the Nfabs and the Go Rhino for the same price.

I'm still debating on getting some also. Just can't decide but I'm sure my steering wheel and door handle would appreciate me getting some :)

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Deadwood
      primary drive belt tensioner

      By Deadwood · Posted

      I bought belts and pulleys for my '20 L5P at Rock Auto a couple years ago. I have used them for many years, and almost always save significant money, especially when I buy maintenance stuff ahead of time.   They carry many OEM parts, which is all I use unless an aftermarket is shown to be same/superior, or if it is an insignificant part or unavailable OEM part anywhere else. RA is usually lower priced, often by a bunch, but parts are sometimes unavailable or out of stock, and I do shop around and sometimes find better prices at other sites.   Be aware that you pay shipping, and if you buy multiple items and they are coming from different warehouses, the shipping can kill the advantage. Planning ahead is best if possible.   If you have a transmission service in the near future, check out their OEM (AC Delco ULV) fluid, usually MUCH less than anywhere else.
    • Deadwood
      10L1000 anyone with High Mileage ? I hate Damocles....

      By Deadwood · Posted

      New member here, very long time occasional guest. Saw this thread, thought it would be a good time to contribute someting. It is only my experience and not a claim that everyone will have the same.   I bought my '20 3500 L5P new and have put 99.9% (literally) of it's current ~400k miles on it myself, with over 50% of that towing loads between 4k to 15k, and to me this truck has been nothing short of amazing. For the first 235k I had zero issues, and from there until 321k I replaced a NOx sensor, two failing glow plugs, and three of the notorious injector connectors. I believe this truck is in part, a testament to good luck, but also good care and following a decent maintenance schedule (I also keep meticulous records.) As a result, it looks as good as a well cared for 70k rig, up and down, inside and out.   At some point before that 321k mile mark I began to get a little spooked about the 10L1000, especially the valve body. Word of mouth about potential issues prompted me to jump on the net to sift through all the noise and determine what all the fuss was about. I routinely take long trips, coast-to-coast and points in between, so roadside breakdowns can be '...a thousand miles from nowhere' and a bit of a challenge, and though I had no issues, my guard was up and activated.   And then I stumbled across a chance to salvage some parts off a new 2025 that had been wrecked in transport. I grabbed a few wear items (alternator, pulleys, etc.) and on a whim asked what the ten speeder would cost me. It was cheap...really cheap. I knew some changes had been made in the '24+ version 10L and were supposedly not compatible, but I called service/parts at my local Chevy dealer and asked why and they didn't know. A call to a well known aftermarket transmission outfit revealed it was very likely it would be fine, but to them not 100% sure.   Because it was cheap (really cheap) and I was spooked, I took the chance. Had it installed by a local shop and it worked like a champ, shifted just like the original. At it's first service at 37k, I had the shop put in a Next Gen valve body kit, which after some initial hiccups and rough shifts, smoothed out though with somewhat firmer shifting.   All that said, I have a very serious concern about my newer transmission as just two weeks ago it suddenly began to exhibit a strong reluctance to engage forward or reverse. It was a bit past due anyway so I took it in for service. The reason it was sticking was due to 'glitter' in the fluid clogging the filter...not good folks, often indicates a converter giving out. We ended up going ahead with the new filter and fluid, first to see if it would move and shift, and then if so buy me a little time. It did, and I've driven it over a thousand miles and it is shifting smooth, no noises or slipping. Regardless, it looks like a third gearbox is in my future so I can resume taking long trips with some confidence. In the very short term, my curiosity will have me examining the fluid to check how much glitter has reappeared.   An earlier poster had alleged, in the context of 10L100 failures, that it is another example of how we seasoned citizens somehow descend into hysteria, lose control of our senses, and react irrationally after brief encounters with the idiocy of the internet infosphere. Let me say (and I have used and abused said internet since it's infancy) there is no segment of the populace that has a corner on over-reaction to digital garbage. Just as my offering of experience in this arena is purely anecdotal and should not be considered gospel or all-encompassing, I believe it is still worthwhile information to consider, along with other relevant anecdotal experiences about things like complex transmissions, especially when balanced with other sources.   So to answer the original question, yes I got high miles out of my first 10L, trouble free for 321,000. Now I really wonder how much longer it would have went. Did I 'overreact' to the internet ghouls by replacing a 'good' one with a 'bad' one? Maybe. Who knows, the thing might have taken a puke a 100 miles later. So I'll just fix it again, then move on and start thinking about all the other stuff that will eventually wear out. It still has the original brakes (they're at ~60%), original injectors/pump, turbo, water pump, etc....pretty much original everything. Knock on wood.
    • swathdiver
      6 Speed vs 8 Speed

      By swathdiver · Posted

      At peak temperature.  They get to cool down and warm up more, especially those with the external cooler.  I have three GMT900s and one of them has over 225K on its original transmission.  Fluid gets changed about every 36K miles, all of it.     It's not the bean counters, it was the government.  They had to meet CAFE standards and other government requirements.   To get around that, we tune them and modify them to our liking.
    • GMCustomerService
      Will not stay in Reverse

      By GMCustomerService · Posted

      Our customers' safety isn't something we take lightly. To ensure you get the proper assistance for your truck's repairs, please fill out the form at https://s.chevy.com/support-request with all pertinent details including your username.
    • GMCustomerService
      2026 Z71 Forward and Rear Park Assist help

      By GMCustomerService · Posted

      We appreciate you sharing your experience with your truck. To ensure we get you the proper assistance, please fill out the form at https://s.chevy.com/support-request with all pertinent details including your username.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...