Jump to content

Have You Smoked A Hemi 5.7 Today?


mikewood31

Recommended Posts

Posted
Relax their ranger Dan, I do not street race nor show off I have no desire to waste my gas doing so

I just do not back down and let them try to cut me off when they want my lane and I don't buy into that Hemi torque crap because it is not measured where it counts ,at the rear wheels.not to mention its measured at 5400 rpm to start

don't know about you but I have never had to rev my truck up that hi to get it moving

and the gear ratio can make a big difference I know people that have owned older ones between gas stations

and repair shops they ran fine so don't get your panties in to big of a knot or you'll fall of your high horse!

 

 

oh I see you weren't racing, instead you were creating a road rage situation so you could preserve your claim to your section of the road and show everyone how manly you are..

 

 

yeah that's MUCH better..

  • Replies 131
  • Created
  • Last Reply
Posted

I have both sides to the OP story. I rage and I relax. I have found a way to fix the rage. I watch a stand up comedian on the touchscreen...my cruise gets set and I don't watch it but knowing that there is something funny and more attention drawing than the people on the road helps...me at least.

Posted
I have both sides to the OP story. I rage and I relax. I have found a way to fix the rage. I watch a stand up comedian on the touchscreen...my cruise gets set and I don't watch it but knowing that there is something funny and more attention drawing than the people on the road helps...me at least.

 

 

XM RawDog and Blue Collar Comedy stations FTW...

Posted
guys whats up with these things?

is this dodges attempt to make a 350 ?

are they geared really low or something?

because my 5.3 just leaves them in the dust at stop lites

and mines stock except for the K&N

and if thats the case my 92 sierra with the 5.7 would have really

smoked them right to the gas station

they even have factory dual exhaust on some of them

just don't seem to have much take off and I'm not punching it

too much but they always try to race me for some reason especially the new ones

if I feel like being a dic I just hit my trailer switch and listen to them trying to

pass me :thumbs:

Heres how I "smoked" a Hemi,,,my cousin bought his new at the same time i got my Silverado used,(around 40k miles)..he,s since blown 2 trannies,,,gobs of tires the engine @ 140k,which Dodge had no sympathy for. He,s on his 3rd truck since then...Me? I,m just plodding along in the ole chevy,,,a rear @ 140K but otherwise no major repairs,3rd full set of tires and no payment book. oh..and 240k miles..hmmm....who won??

Posted

I don't see how any stock chevy 5.3 beats a 5.7 hemi, but my 6.2 does, big time. I have raced several here around town and none of them come even close. They hang with me for about 5 seconds and then it's all over.

Posted
guys whats up with these things?

is this dodges attempt to make a 350 ?

are they geared really low or something?

because my 5.3 just leaves them in the dust at stop lites

and mines stock except for the K&N

and if thats the case my 92 sierra with the 5.7 would have really

smoked them right to the gas station

they even have factory dual exhaust on some of them

just don't seem to have much take off and I'm not punching it

too much but they always try to race me for some reason especially the new ones

if I feel like being a dic I just hit my trailer switch and listen to them trying to

pass me :thumbs:

Heres how I "smoked" a Hemi,,,my cousin bought his new at the same time i got my Silverado used,(around 40k miles)..he,s since blown 2 trannies,,,gobs of tires the engine @ 140k,which Dodge had no sympathy for. He,s on his 3rd truck since then...Me? I,m just plodding along in the ole chevy,,,a rear @ 140K but otherwise no major repairs,3rd full set of tires and no payment book. oh..and 240k miles..hmmm....who won??

 

 

I have simular thing, brother in law has a Ram 3500 with the cummins

we bought our trucks at the same time, engine is bulletproof on that truck

because he goes to cummins only for engine maintainence

too bad hes on his 3rd set of ball joints ,2nd steering box ,2nd set of hubs

and various others seals and parts that I have never replaced on any of my GM trucks

never mind my silvy, your right thats they way chevy will always win

Posted
Relax their ranger Dan, I do not street race nor show off I have no desire to waste my gas doing so

I just do not back down and let them try to cut me off when they want my lane and I don't buy into that Hemi torque crap because it is not measured where it counts ,at the rear wheels.not to mention its measured at 5400 rpm to start

don't know about you but I have never had to rev my truck up that hi to get it moving

and the gear ratio can make a big difference I know people that have owned older ones between gas stations

and repair shops they ran fine so don't get your panties in to big of a knot or you'll fall of your high horse!

 

 

LOL.....sounds like you have an ego problem that may cause you to seriously injur or kill somebody. Putting others in danger and potential to kill someone on the highway because it hurts your ego if somebody passes you. Gotta love some of these people. Not sure if you realise it or not but hammering on the throttle when someone attemps to pass you is wasting your gas.

 

These type of people are the ones we like to pull over on the highway and issue them citations for reckless driving, seeding, and failure to yield. What a moron!

Posted

I traded in a Dodge with the 5.7 Hemi for this new Chevy truck so I feel qualified to speak on this.

 

I'd say at 20-60mph this with the 6sp and 3.42's this new Chevy pulls harder. Top end, that Hemi would smoke this current truck. It had 3.92 gear ratio limited slip.

 

And that was the 2008 Hemi with 345 hp.

 

My neighbors truck is the new one with the 390 hp Hemi.

 

No way in hell are these trucks going to beat that. 0-60 or beyond. That truck is a beast.

 

 

I will say this 6 spd transmission does a really good job getting the power to the ground. I'm actually impressed. I can tell the difference on the top end....I would think headers, CAI, exhaust and tune would easily get these 5.3L motors up to speed and around 350 hp and in range with the current motors.

 

As the 5.3 sits stock, on the low end 0-60, with 3.42's, my truck will run pretty close to the older Hemis until you hit 60mph....then you 'd lose out.

 

 

The new hemi's will mop this truck all over the road. Doesn't mean this truck is not going to work.

 

I had a 1991 Chevy that had the old 350 and it was rated at 230 hp. My 2003 ford had 260hp in it's 5.4 and it was enough for what I did. The 2004 Ford had 310 HP and did not feel as good as this 5.3 does.

 

So the 5.3 with 315hp is more than enough. 350 would be better though.....390 may be too much.

 

Those Hemi's are really good motors. Dodge makes a crappy suspension and the ride isn't very good but they make a damn good motor.

Posted
Relax their ranger Dan, I do not street race nor show off I have no desire to waste my gas doing so

I just do not back down and let them try to cut me off when they want my lane and I don't buy into that Hemi torque crap because it is not measured where it counts ,at the rear wheels.not to mention its measured at 5400 rpm to start

don't know about you but I have never had to rev my truck up that hi to get it moving

and the gear ratio can make a big difference I know people that have owned older ones between gas stations

and repair shops they ran fine so don't get your panties in to big of a knot or you'll fall of your high horse!

 

 

LOL.....sounds like you have an ego problem that may cause you to seriously injur or kill somebody. Putting others in danger and potential to kill someone on the highway because it hurts your ego if somebody passes you. Gotta love some of these people. Not sure if you realise it or not but hammering on the throttle when someone attemps to pass you is wasting your gas.

 

These type of people are the ones we like to pull over on the highway and issue them citations for reckless driving, seeding, and failure to yield. What a moron!

 

 

 

I tend to see this type of agressive driving done by women when I am on my way home from work.

 

What ever poor decisions he has made the name calling doesn't make you any better.

  • 1 month later...
Posted

Sounds like a lot of angry replies, over something that should be ignored. OP, try to keep your cool on the road. Everyone else, keep your cool on the web eh?

ps my 4.8 couldn't hold a candle to a friends 06 hemi. specially since the torque limiting on the gm makes for teribble slow takeoffs.

  • 2 weeks later...
Posted
Relax their ranger Dan, I do not street race nor show off I have no desire to waste my gas doing so

I just do not back down and let them try to cut me off when they want my lane and I don't buy into that Hemi torque crap because it is not measured where it counts ,at the rear wheels.not to mention its measured at 5400 rpm to start

don't know about you but I have never had to rev my truck up that hi to get it moving

and the gear ratio can make a big difference I know people that have owned older ones between gas stations

and repair shops they ran fine so don't get your panties in to big of a knot or you'll fall of your high horse!

 

 

LOL.....sounds like you have an ego problem that may cause you to seriously injur or kill somebody. Putting others in danger and potential to kill someone on the highway because it hurts your ego if somebody passes you. Gotta love some of these people. Not sure if you realise it or not but hammering on the throttle when someone attemps to pass you is wasting your gas.

 

These type of people are the ones we like to pull over on the highway and issue them citations for reckless driving, seeding, and failure to yield. What a moron!

 

 

 

I tend to see this type of agressive driving done by women when I am on my way home from work.

 

What ever poor decisions he has made the name calling doesn't make you any better.

 

 

Ok Dr. Phil, I am pretty sure NOBODY that made a comment on his post said they were "better" than him...... let me explain something to you..... the word "moron" describes him perfectly. These are the kind of acts that get innocent people killed on the highway. Not yielding to traffic and slamming the throttle to the floor because this guys ego won't allow him to be passed in traffic IS going to cause an accident and most likely cause someone serious bodily harm. I am positive if this happened to someone in your family you would agree, anyone who does this and then brags about it is a moron. People like this should not be allowed to drive. Don't know how many fatal accidents I responded to due to these ego maniacs, it's a shame.

Posted

Op made me lol the most when he said his 92 would beat a hemi...all 210 hp of the almighty 350 lolololol

 

 

That is assuming it is stock...

Archived

This topic is now archived and is closed to further replies.

  • Latest Articles

  • Posts

    • So, do I go elbow-deep on this thing or list it for sale and play dumb? Seems to "runs good."   I'm about $1200 away from having: -a rebuilt injector ($300) -a new cat ($250) -a new cat back exhaust (OE style) ($300) -a new AC compressor ($200) -AC refrigerant charge ($150)   In theory, this should rectify the obvious detracting issues from its value and operability. Cold AC with a non-squeaking AC pulley both sounds and feels good. An exhaust that isn't cut/hacked in 17 different places and doesn't vibrate on a crossmember would make it sound and feel less janky. A working cat would help the stink, and will save the earth, but *if and only if* the fuel system is working properly, which would also address the intermittent "rich" CEL.   Heard a good one... CEL for "Rich condition" means you haven't spent enough money on the truck lately, and it's letting you know.   Rebuilding the injector would seem to be the most important part. Replacing the cat would be secondary. I don't think mine is plugged or overly restricted, but it might be a little restricted? I have no good way to tell other than seat of the pants feel. I hate the smell.   The current theory is I have a rich idle problem: A bad fuel pressure regulator, or a leaking injector(s) being the highest probabilities. I already replaced the FPR but that doesn't mean its replacement isn't also bad. It was a new part from Dorman, but the packaging looked like it had been sitting on a shelf for 20 years.   This is the (single) upstream O2 sensor shown at idle. I'm getting a lot of "rich" it seems. Sometimes it stays high like that and doesn't drop down. That makes me think it's processing injector leaks or a partially stuck open injector.     Other times it looks like this. Nice oscillations between rich and lean, which is what I think it should be. Under load and at speed, the oscillations are nice and tight and uniform looking, high and low.     Fuel trims suggest the PCM is compensating pretty hard at idle to pull fuel out. But it's not enough to trip a CEL. Something about slowing to a stop: brake vaccum booster, EGR, or the EVAP purge is delayed, or there's pooled fuel in the intake again that's draining into a cylinder is enough to set the CEL. Of course, in two days of driving, it hasn't set. I was hoping to actually look at the freeze-frame data when it sets. IAT is high because it's idling on an 83 degree day here.  
    • Have considered installing a DC to DC charger in your camper to replace your isolator?  
    • Common failure.  You need to replace the fuel door housing.   The painted cover transfers over to the new housing.  To remove the old one there is 4 spots where you poke the plastic to release it.  
    • No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...