Jump to content

Recommended Posts

Posted

Pulled bumper for new lower valence and fog lights. Luckily (I think) I know what I'm doing lol

 

5yne7a2y.jpg

 

Sent while in 'Murica...

Posted

Where did you source the valence from?

 

Sent from my LG-D800 using Tapatalk

Posted

Where did you source the valence from?

 

Sent from my LG-D800 using Tapatalk

 

eBay, got it for $45 shipped. fits like stock

Posted

You lucky ****. The cheapest I've found so far is around 100. I'm seriously considering just doing a cow catcher instead

 

Sent from my LG-D800 using Tapatalk

Posted

You lucky ****. The cheapest I've found so far is around 100. I'm seriously considering just doing a cow catcher instead

 

Sent from my LG-D800 using Tapatalk

Does your truck have the Oval or round fog lights?

 

Sent while in 'Murica...

Posted

Same as yours

 

Sent from my LG-D800 using Tapatalk

Oval

 

Sent from my LG-D800 using Tapatalk

Posted

Get a real bumper... You know you'll just bust it again, lol.

Don't you put that on me lol

 

Sent from my LG-D800 using Tapatalk

Posted

A winch bumper is actually not priced too bad but the 3" body lift mod for my truck is $300 plus all the other accessories I would want. It came out to 1600

 

Sent while in 'Murica...

Posted

post-126915-0-46605700-1405291106_thumb.jpg

 

Went back to hunting land today shooting lanes cut roads cut ready to drop some corn and mineral blocks, can't wait for deer season. I'm so excited I almost peed on myself.

post-126915-0-46605700-1405291106_thumb.jpg

post-126915-0-46605700-1405291106_thumb.jpg

post-126915-0-46605700-1405291106_thumb.jpg

  • Like 2
Posted

attachicon.gifimage.jpg

 

Went back to hunting land today shooting lanes cut roads cut ready to drop some corn and mineral blocks, can't wait for deer season. I'm so excited I almost peed on myself.

Nice i know where your talking about, i work in Eastover. Do you have any hogs on the place?
  • Like 1
Posted

No hogs but I know a guy with some land behind Beech Creek golf course that has them and he lets me get some from time to time I got 4 last year.

Posted

Contacted performabuilt about the noise coming from the tranny and sent him a sound clip. He said he can't identify the sound or imagine what it could be. Told me to keep driving it. I have a feeling I'm gonna be paying for a tow bill soon...

 

Sent while in 'Murica...

Posted

No hogs but I know a guy with some land behind Beech Creek golf course that has them and he lets me get some from time to time I got 4 last year.

I heard that! Hollar at me if you need some some help taking out some hogs or deer. Have gun(s), will travel lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • This is interesting. My quote tagged here is different from my original quote. After I’m driving them longer. That isn’t me. I don’t talk that way. I definitely wouldn’t express myself that way. Interesting.
    • I have the same running boards on my truck and I do agree they are bulky. I also find myself stepping over them when getting in and out of the truck. Besides providing protection to the rocker panels, they aren't very useful.  I will be replacing them soon with the Amp Powersteps. 
    • Monthly payment is only part of the equation. With today's prices and interest rates, I'd look at the total monthly cost: payment, insurance, registration, fuel, maintenance, and expected repairs. A vehicle that fits comfortably into your budget is usually the better choice than stretching for a higher trim. I've also kept my vehicles longer over the past few years. New cars have gotten expensive enough that driving one for 10+ years, while staying on top of maintenance, often ends up being the most cost-effective approach.
    • 10 Ford and Chevy engines proven to reach 300,000 miles   You may note a common 3K OCI on this list of gas motors. I skipped over the diesels. Dh'O. 
    • Thanks newdude!  By the time manual selection is needed, I'm probably too much of a control-freak to depend on the transmission sensing braking to activate automatic downshifting.  I would be anticipating the situation and already be manually downshifting.   This truck replaced a 2004.5 LLY diesel with the Allison 5-speed.  Putting it in T/H made noticeable differences (when the torque converter locked, upshift points, downshift behavior).  On this 2024 gasser with the 10L1000 I haven't been able to detect much, if any, difference.  Ok, I can never tell now when the torque converter locks up.  But I also don't notice differences in shifting.  For downhills, I've probably already manually downshifted by then anyway.  Since it's also more awkward (than the 2004.5) to engage/disengage I don't even bother.  Or maybe it doesn't really matter with just a 3k lb. camper in the bed?   Thanks also for the list of reasons the charging system might select various voltages.  However, what I am seeing doesn't fall into any of those categories.  It very definitely, and very consistently, rises after coasting/braking.  Maybe not immediately, but not very long after coasting/braking.  Very consistently drops voltage when no longer coasting/braking.  It might also be interacting with the camper battery charging (I might disconnect the camper and see if it changes the charging behavior).  I also need to recheck turning on headlights for when I want to force it to charge the camper.   Another JR, in June I converted the camper to LiFePO4.  Since it's not a good idea to try to charge lithiums directly using truck, I installed a Victron Orion XS DC-DC charger (which BTW is AMAZING!!).  Being cheap, I only had to buy that one item (besides the battery, of course) to do the conversion.  The camper OEM 120v battery charger (only 19 years old and works perfectly) and the truck feed the input to the DC-DC charger (not at the same time).  But I didn't want the camper charger feeding back to the truck so I kept the old separator.  I considered replacing the separator with a 30amp diode but that means more work and might add another 1/2 volt drop.  One thing that surprised me was the voltage drop over the long 10awg wire run, so I can only charge smoothly at 8 amps (because the DC-DC charger is completely configurable).  Another reason I don't want an added voltage drop with the diode.  I might also be a little lazy but all this work is being done under the sink with a small cabinet opening.    
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...