Jump to content

Recommended Posts

Posted (edited)

^^^^^^That's the same exact setup I want to do! How far do you stick out if any? And More pics if would please! also, did you put the rear block in?

Edited by cameronfaber
Posted

RC 2 1/2" w rear 2" blocks and 290/60/20 terra grappler g2's on stock +27 rims. Turned out perfect!!!

9d1011fb6b480c2d0e043e22e09174d2.jpg

 

 

Sent from my iPhone using Tapatalk

  • Like 1
Posted (edited)

 

^^^^^^That's the same exact setup I want to do! How far do you stick out if any? And More pics if would please! also, did you put the rear block in?

Barely any stickout. maybe an inch with the sidewall tread. 2 inch block to replace the stock 1 inch

2lk8v45.jpg

another picture

6r801d.jpg

Edited by Bigmoore
  • Like 1
Posted

Your truck just made me pull the trigger on that size tire but can you take one more and show me how wide them tires are. And sick truck btw

 

They are 11.5" wide, but thank you!

2prvg37.jpg

  • Like 1
Posted

Barely any stickout. maybe an inch with the sidewall tread. 2 inch block to replace the stock 1 inch

2lk8v45.jpg

another picture

6r801d.jpg

Whats the offset of those wheels? Looks really nice
Posted

4085027d0a5875bcf1905a60c2ae24e2.jpg

 

 

Sent from my iPhone using Tapatalk

cb01c71a5f4b8e76f26ef8a7018fc8d0.jpg

 

 

Sent from my iPhone using Tapatalk

e1cf912953f7208e4cb6d7a61df9fc57.jpg

 

 

Sent from my iPhone using Tapatalk

a62f56b0692faf73abecdd0bf1d4ccd1.jpg

 

 

Sent from my iPhone using Tapatalk

  • Like 2
Posted

orpbi1.jpg

 

Finally got mine done. 2.5" RC level with 18" Fuel Mavericks wrapped in 285/65-18 Nitto Trail Grapplers

I forgot to ask you any rub at a full lock forward or reverse? And if so any trimming?
Posted

I forgot to ask you any rub at a full lock forward or reverse? And if so any trimming?

No I do not rub at all. No trimming either

 

 

Sent from my iPhone using Tapatalk

Posted

Good to hear thanks man for all your help!

no problem!

 

 

Sent from my iPhone using Tapatalk

Posted

What leveling kit are you running?

 

 

Sent from my iPhone using Tapatalk

Let me call the shop n I'll post it up, also I tried uploading more pics but I get errors that the files are too big. The shop is in McAllen, Tx called M&M off-road center

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,979
    Total Members
    8,960
    Most Online
    rayredbone
    Newest Member
    rayredbone
    Joined
  • Who's Online   1 Member, 0 Anonymous, 495 Guests (See full list)


  • Latest Articles

  • Posts

    • Question @diyer2 on this line if you please. Are you saying the shudder is the system turning on and off at the frequency of the shudder? Guess I'm asking if you are saying you have seen it do this with the bi-direction scan tool in graph mode? If so have you been able to discern the 'trigger'. Something is telling to cycle rapidly.    My truck just started doing this recently. 197K on the clock. My response has been M5 anything under 55 mph. I treat it like a lugging stick shift. Gear down and let it spin a bit. Engauge M5, then tow mode and then M6 lets the trans stay in 5th but the AFM is active. Smooth like Skippy.    My thought was that as a machine ages the friction gets lower and as the system is load based, the lower friction would allow it to turn on at ever lower rpm until it reaches the lugging point. And yes I am ignorant of any minimum rpm requirement for the system. If you know that would be useful information.    As you know I run a Scan-Gauge II which allows me to watch the On/Off of the signal to the VLOM. While in the shudder mode I'm not seeing is cycle at that frequency or at all for that matter outside the triggers @newdude posted a few years back. Now is it possible that the refresh rate isn't fast enough to catch it? Maybe. It is why I asked my first question about graphing and trigging parameter.     As we have observed from members here the failure point is all over the map miles wise as you note yourself in your opening post. That by itself begs a few questions like fellows that comment on these lifters failing even after the system has been disabled. Long after. 😬   https://www.enginelabs.com/news/tech-tips-replacing-ls-active-fuel-management-lifters-with-melling/   The Gen5 lifters operate the same as the LS versions. In fact they are the same lifter.    https://www.enginelabs.com/tech-stories/sorting-out-gen-v-lt-lifter-failure-with-a-simple-valvetrain-fix/        
    • UPDATE 2: Steering wheel control backlights and control of the cluster can supposedly be achieved by adding a wire to pin 20 of the cluster and tapping it to pin 2 of the main clock spring harness. I'm going to give it a shot - will update  
    • GM Global A pickups 2019-2022 can do OTA programming for the radio.  GM VIP (GM Global B) can do OTAs for almost every module on board.  So a 2022.5 and newer pickup can do OTAs for recalls like the 2.7 fuel flow recall.  EVs get OTAs that improve one pedal driving, radio issues, HVAC issues, updated battery management software, etc.     So age of the vehicle/what GM electrical platform its on will alter what amount of updates can be pushed on OTAs.  
    • Thank You.   So far my new ride is making me look like a genius for going with the 3.0L, as my first fuel refill occurred over three weeks from when I took delivery.  This engine combination is very amazing.  So far no issues and had not done a regen yet.
    • I am curious as to how much fluid you put back in the transmission ( assuming you had replaced the filter to compare to my findings ) and then went through the process of warming up the trans before pulling the check plug to drain out the excess and if you measured how much came back out.    I just found it surprising that some claimed a certain amount less fluid being put in and then draining some back out. The attitude of the truck as per if the surface is level and how the trucks stance is would make quite a difference since the check plug is right at the front of the transmission. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...