Jump to content

Disabling Daytime Running Lights (DRL)

LTZTom

By LTZTom
in Modifications & Accessories

 Share

Recommended Posts

Matt DiMarco Enthusiast

Matt DiMarco

Posted
Posted

So all I have to do is in the headlight swap pin B and E on the left and B and E for the right?

 

also below is for 2015 sierra SLE 4wd

DOC1.pngDOC2.png

Yes, swap the pins inside the connector on the truck side. You don't need to touch the other side of the connector attached to the headlight.
  • Replies 319
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

MotoMedic
MotoMedic

"I was a firefighter for 30 years" sounds like a qualifying statement.. if not intended that way, my mistake. And I never said you were evil. I clearly stated "everyone should be free to choose if the

VMaxtastic
VMaxtastic

Why? They're for safety. Not sure if you've ever seen the result of a head on collision... I bet you would change your tune if you did.

VMaxtastic
VMaxtastic

I'll take paying for a bulb over getting smoked by someone that isn't paying attention any day. Lots of people are too clueless to turn on their headlights in low visibility conditions.. I personally

Posted Images

  • 2 weeks later...
Velocibiker Enthusiast

Velocibiker

Posted
Posted (edited)

What I'd like to have is the fogs act as my DRLs. But not have the parking lights come on as well. Could using relays work to turn on just the fogs? Everything else work as normal.

Edited by Velocibiker
  • 5 months later...
Cash459 New Member

Cash459

Posted
Posted

Correct... its very simple, just need some very fine point tools to get the pins out of the connector. Start by removing the 2 grey peices. there is one on the front and back of connector.

Sorry to dig up this old topic again but I'm trying to disable my DRLs & decided to do the pin swap method. I found the connector behind the headlight on the driver side & swapped the B & E pins but now I have another issue. When the headlight switch is in the "auto" position, the driver side headlight stays on as the DRL but the passenger side it's the parking light (amber). If I turn the headlight switch to the "on" position, then all the lights work normally. Am I doing something wrong or is there something else that I need to do? Or even worse, did I mess up something on my pins/connector? ANY help or guidance is GREATLY appreciated!!

Matt DiMarco Enthusiast

Matt DiMarco

Posted
Posted

Sorry to dig up this old topic again but I'm trying to disable my DRLs & decided to do the pin swap method. I found the connector behind the headlight on the driver side & swapped the B & E pins but now I have another issue. When the headlight switch is in the "auto" position, the driver side headlight stays on as the DRL but the passenger side it's the parking light (amber). If I turn the headlight switch to the "on" position, then all the lights work normally. Am I doing something wrong or is there something else that I need to do? Or even worse, did I mess up something on my pins/connector? ANY help or guidance is GREATLY appreciated!!

Start over.

Which year and model is your truck?

Did you swap the correct wires on the "truck side" of the headlight connector?

Did you do the same thing on both driver and pssenger side?

Sounds like you may have messed up the driver side since the low beam is staying on in daylight in the auto position.

Check your work, sometimes its better to put everything back to stock and start over.

Cash459 New Member

Cash459

Posted
Posted

Start over.

Which year and model is your truck?

Did you swap the correct wires on the "truck side" of the headlight connector?

Did you do the same thing on both driver and pssenger side?

Sounds like you may have messed up the driver side since the low beam is staying on in daylight in the auto position.

Check your work, sometimes its better to put everything back to stock and start over.

I have a 2015 Silverado LTZ.

 

Yes, I did swap the correct wires on the "truck" side of the drivers side (or at least I thought I did) but now that I'm having issues, I was thinking that I need to go back & switch everything back to original & start again.

 

I did not do the passenger side yet, only the driver side. I was trying to make sure I at least got one side correct before doing both.

 

I'll switch the driver side back to original, start with the passenger side next time & then go from there.

 

I'm also wondering if there is a wire that's loose in the connector on the driver side also because now when I put the truck in drive from park with the headlight switch in the "on" position, the passenger headlight cuts out completely.

 

Starting to think I created a gremlin. Hopefully putting everything back to original & starting over will fix the issues.

Cash459 New Member

Cash459

Posted
Posted

Anyone know what size/gauge wire to use to re-wire the factory harness??

 

My harness on the "truck"/female side seems to have some loose terminals & I plan on re-wiring it with new female connectors & a new harness housing to ensure that I don't have any issues moving forward.

 

Just want to make sure I use the right size wire for those terminals.

 

Thanks in advance for any help/suggestions!

  • 1 month later...
Cash459 New Member

Cash459

Posted
Posted

Start over.

Which year and model is your truck?

Did you swap the correct wires on the "truck side" of the headlight connector?

Did you do the same thing on both driver and pssenger side?

Sounds like you may have messed up the driver side since the low beam is staying on in daylight in the auto position.

Check your work, sometimes its better to put everything back to stock and start over.

Sorry to bother you Matt, but you seem to be the only one still responding to this thread....

 

So I finally got the parking lights to be my DRLs with the wire swap you posted about but I had a couple of

quick questions:

1. Is there a way to have the fog lights on with the DRLs (now parking lights)?? Anytime I push the button for the fogs, my headlights turn on. Or is that just a sacrifice from the wire/pin swap?

 

2. ANY time I use my remote start function, the headlights automatically turn on. Is that a normal operation & is there a way to prevent that? I ask because I have HIDs installed & don't want to compromise the life of the bulbs from the constant on/off. Or is the only way to prevent that to do the trick of removing the spring from the auto control light switch & leaving it in the off position?

 

Thanks to any and all who can help with this...

Matt DiMarco Enthusiast

Matt DiMarco

Posted
Posted

Sorry to bother you Matt, but you seem to be the only one still responding to this thread....

 

So I finally got the parking lights to be my DRLs with the wire swap you posted about but I had a couple of

quick questions:

1. Is there a way to have the fog lights on with the DRLs (now parking lights)?? Anytime I push the button for the fogs, my headlights turn on. Or is that just a sacrifice from the wire/pin swap?

 

2. ANY time I use my remote start function, the headlights automatically turn on. Is that a normal operation & is there a way to prevent that? I ask because I have HIDs installed & don't want to compromise the life of the bulbs from the constant on/off. Or is the only way to prevent that to do the trick of removing the spring from the auto control light switch & leaving it in the off position?

 

Thanks to any and all who can help with this...

1. The fog lights trigger the amber lights. You are now using the amber light wire to power headlights. Unfortunately, you can not use fogs without low beams unless you buy a special harness online, not sure where. You will have to undo the pin swap mod.

2. This is a sacrifice you make for the pin swap, low beams come on when started remotely. I tapped into the trigger wire in the HID kit and put a toggle switch on my dash. As long as I leave the switch off. headlights stay off when i remote start. If it's dark flip the switch before you drive.

Matt DiMarco Enthusiast

Matt DiMarco

Posted
Posted

Sorry to bother you Matt, but you seem to be the only one still responding to this thread....

 

So I finally got the parking lights to be my DRLs with the wire swap you posted about but I had a couple of

quick questions:

1. Is there a way to have the fog lights on with the DRLs (now parking lights)?? Anytime I push the button for the fogs, my headlights turn on. Or is that just a sacrifice from the wire/pin swap?

 

2. ANY time I use my remote start function, the headlights automatically turn on. Is that a normal operation & is there a way to prevent that? I ask because I have HIDs installed & don't want to compromise the life of the bulbs from the constant on/off. Or is the only way to prevent that to do the trick of removing the spring from the auto control light switch & leaving it in the off position?

 

Thanks to any and all who can help with this...

Just want to add to my last post...

This may be obvious, but adding a toggle switch to the thin blue wire in the HID kit (the wire that conects to the trucks low beam bulb commector) will allow you to use your fogs without your low beams. Its easy and takes about 10 mins to run a wire through the firewall into your cabin.

  • 2 weeks later...
  • 4 months later...
Kohl531 New Member

Kohl531

Posted
Posted
On 3/4/2016 at 8:37 AM, Matt DiMarco said:

You must have a Canadian truck. On US trucks the lights can be turned off while in drive. Im in Canada as well, I swapped the low beam wire with the parking lamp wire so the orange lights are on in daylight and the low beams still turn on automatically when it gets dark.

I have a 2014 GMC Sierra WT that is Canadian.  Will this mod work for my truck or just the silverados?  Sorry I’m new here 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • PunchT37
      Parking Brake - Automatic Engagement Questions

      By PunchT37 · Posted

      I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...