Jump to content

2014 chrome trim question/opinions needed

holliday26

By holliday26
in Modifications & Accessories

Recommended Posts

holliday26 Enthusiast

holliday26

Posted
Posted

wwyd?

 

I own a gmc 1500 AT double cab. I hate the chrome and love color matched everything!........so im planning on doing this huge ****ing swap which is gonna be a huge hassle yada yada yada . So any way I run into this guy with a Chevrolet double cab 1500 same truck essentially without all the bells and whistles boo shit. So dudes says "I want all of your chrome " (Hispanic guy). So im super juiced!.......... so I begin the process of pricing out all these parts to color match( handles, bezels, mirror cap, door trim, window trim.)

 

 

heres the big question I need your opinions on!!!

 

 

the chrome is used and useless to me but still worth money and is not useless to this guy. what is a fair way to price this stuff out or sell it to him ?

 

option 1: my CM'd parts without paint are 560 not installed..... I tell him pay half that $280 and he gets all my chrome?

 

 

its ****ed on my end b/c all my chrome trim and handles bolts rite on to his truck, no issues for him. on my end I have to remove the chrome, buy all new parts blank then color match em and re-install. going to cost shit tone more than 50% im charging him not including the labor to do this stuff

 

 

 

suggestions please!?

 

thanks

spiGini Enthusiast

spiGini

Posted
Posted

Well its your choice to sell him the parts, he shouldn't have to pay higher just cause you have to take it off. If you don't want to do the work don't sell them. If everybody who took stuff off their truck put the "labor" into the price we might as well buy from a dealership.

 

if you look on shopchevyparts.com they have the cost of the chrome handles and everything else on their. Check and price accordingly, depending on the condition of yours.

22_AT4 Enthusiast

22_AT4

Posted
Posted

Are you swapping out your back bumper? Mine is chrome and I wish I had the black one that comes on the work truck. I just had my wheels painted black (getting black lugs) and I'm thinking about blacking out the silverado on the doors.

 

Thanks,

Skeeter McSkeet Senior Enthusiast

Skeeter McSkeet

Posted
Posted

I'd just do a swap with him and get them painted, instead of purchasing all new parts AND paying to have them painted. I also wouldn't pay to have any of these parts installed. Check toney green on eBay, he is always listing painted handles and mirror cap take offs in excellent shape. I just got a set of onyx black handles from him last week in flawless condition.

 

 

-Skeet

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • mysery1
      What have you done to your K2 today?

      By mysery1 · Posted

      I have a 2018 Silverado Custom with 156k on the odometer. In the last month I've replaced the plugs, wires and the driver side engine mount. My wife just returned from a trip of about 1500 miles and told me the brakes are making a grinding noise when applied. I drove it and looked it over and this is what I found with the driver's side rear rotor.   I'm going to order new pads and check about having the rotor resurfaced. Hopefully this is easier than the last 2 jobs.   Peace  
    • FiLo
      5.3 / 6.2 valve covers / oil burning

      By FiLo · Posted

      Any update if the new valve cover help with the oil consumption?  I have a 2014 GMC sierra and my truck is consuming a lot of oil so I’m wondering if replacing the driver side valve cover will stop some of the oil consumption. Thanks 
    • Deadwood
      primary drive belt tensioner

      By Deadwood · Posted

      I bought belts and pulleys for my '20 L5P at Rock Auto a couple years ago. I have used them for many years, and almost always save significant money, especially when I buy maintenance stuff ahead of time.   They carry many OEM parts, which is all I use unless an aftermarket is shown to be same/superior, or if it is an insignificant part or unavailable OEM part anywhere else. RA is usually lower priced, often by a bunch, but parts are sometimes unavailable or out of stock, and I do shop around and sometimes find better prices at other sites.   Be aware that you pay shipping, and if you buy multiple items and they are coming from different warehouses, the shipping can kill the advantage. Planning ahead is best if possible.   If you have a transmission service in the near future, check out their OEM (AC Delco ULV) fluid, usually MUCH less than anywhere else.
    • Deadwood
      10L1000 anyone with High Mileage ? I hate Damocles....

      By Deadwood · Posted

      New member here, very long time occasional guest. Saw this thread, thought it would be a good time to contribute someting. It is only my experience and not a claim that everyone will have the same.   I bought my '20 3500 L5P new and have put 99.9% (literally) of it's current ~400k miles on it myself, with over 50% of that towing loads between 4k to 15k, and to me this truck has been nothing short of amazing. For the first 235k I had zero issues, and from there until 321k I replaced a NOx sensor, two failing glow plugs, and three of the notorious injector connectors. I believe this truck is in part, a testament to good luck, but also good care and following a decent maintenance schedule (I also keep meticulous records.) As a result, it looks as good as a well cared for 70k rig, up and down, inside and out.   At some point before that 321k mile mark I began to get a little spooked about the 10L1000, especially the valve body. Word of mouth about potential issues prompted me to jump on the net to sift through all the noise and determine what all the fuss was about. I routinely take long trips, coast-to-coast and points in between, so roadside breakdowns can be '...a thousand miles from nowhere' and a bit of a challenge, and though I had no issues, my guard was up and activated.   And then I stumbled across a chance to salvage some parts off a new 2025 that had been wrecked in transport. I grabbed a few wear items (alternator, pulleys, etc.) and on a whim asked what the ten speeder would cost me. It was cheap...really cheap. I knew some changes had been made in the '24+ version 10L and were supposedly not compatible, but I called service/parts at my local Chevy dealer and asked why and they didn't know. A call to a well known aftermarket transmission outfit revealed it was very likely it would be fine, but to them not 100% sure.   Because it was cheap (really cheap) and I was spooked, I took the chance. Had it installed by a local shop and it worked like a champ, shifted just like the original. At it's first service at 37k, I had the shop put in a Next Gen valve body kit, which after some initial hiccups and rough shifts, smoothed out though with somewhat firmer shifting.   All that said, I have a very serious concern about my newer transmission as just two weeks ago it suddenly began to exhibit a strong reluctance to engage forward or reverse. It was a bit past due anyway so I took it in for service. The reason it was sticking was due to 'glitter' in the fluid clogging the filter...not good folks, often indicates a converter giving out. We ended up going ahead with the new filter and fluid, first to see if it would move and shift, and then if so buy me a little time. It did, and I've driven it over a thousand miles and it is shifting smooth, no noises or slipping. Regardless, it looks like a third gearbox is in my future so I can resume taking long trips with some confidence. In the very short term, my curiosity will have me examining the fluid to check how much glitter has reappeared.   An earlier poster had alleged, in the context of 10L100 failures, that it is another example of how we seasoned citizens somehow descend into hysteria, lose control of our senses, and react irrationally after brief encounters with the idiocy of the internet infosphere. Let me say (and I have used and abused said internet since it's infancy) there is no segment of the populace that has a corner on over-reaction to digital garbage. Just as my offering of experience in this arena is purely anecdotal and should not be considered gospel or all-encompassing, I believe it is still worthwhile information to consider, along with other relevant anecdotal experiences about things like complex transmissions, especially when balanced with other sources.   So to answer the original question, yes I got high miles out of my first 10L, trouble free for 321,000. Now I really wonder how much longer it would have went. Did I 'overreact' to the internet ghouls by replacing a 'good' one with a 'bad' one? Maybe. Who knows, the thing might have taken a puke a 100 miles later. So I'll just fix it again, then move on and start thinking about all the other stuff that will eventually wear out. It still has the original brakes (they're at ~60%), original injectors/pump, turbo, water pump, etc....pretty much original everything. Knock on wood.
    • swathdiver
      6 Speed vs 8 Speed

      By swathdiver · Posted

      At peak temperature.  They get to cool down and warm up more, especially those with the external cooler.  I have three GMT900s and one of them has over 225K on its original transmission.  Fluid gets changed about every 36K miles, all of it.     It's not the bean counters, it was the government.  They had to meet CAFE standards and other government requirements.   To get around that, we tune them and modify them to our liking.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...