Jump to content

Recommended Posts

Posted

Yes as far as it will go, but raising the gas makes them closer together.

Once your muscle memory adapts to the new locations you'll find that with the seat adjusted they will seem lower.

I pull the telescopic wheel all the way out and move the seat back a little this way the pedals are farther away.

You'll also find if you lower the front of the seat all the way and adjust height of the rear of the seat you can keep your heels on the floor and with the pedals at the right locations it's much easier to navigate the pedals

 

 

Sent from my iPhone using Tapatalk

 

Not everybody has the telescoping wheel. Also I don't like the feeling when the seat back is higher than the front of the seat, makes me feel like I'm about to fall out of the seat. I would hate the seat to be like that when I'm riding country roads, especially the once up in Virginia. I need the front of my seat higher than the rear of it so I feel more "planted" in the seat, especially since it's bucket seats.

 

I don't have a problem with the pedal positions, just pointing those out lol.

Posted

Ive always liked the pedal spacing horizontally on GMs. But I'm 6', 240 lbs, power lifters build, with size 14 boots. So I kinda need the extra space. Never really paid attention to the difference in height though.

 

I would try what the one guy said

 

Lower your pedals as low as possible

 

Then disconnect the power wire to the brake pedal adjuster.

 

Then use your pedal adjustment switch to raise your pedals, but it will only raise your gas pedal.

Posted (edited)

This is embarrassing lol, but here it goes...

As ghetto as this is... The picture below shows my pedal set-up for the last two months.

Yes, that is a rubber door-stop attached to my gas pedal with two zip-ties.

It sux that I had to resort to this on a 55K car. But, it has helped tremendously and only costs $5!!! My pedals are perfectly aligned now.

 

dQBLK2P.jpg

 

I still think this is part of the issue. Some people want a car and buy a fancy truck and expect it to be like fancy cars of similar cost. I'm guilty of it in in a lot of ways. But, when I'm tromping around in size 12 hunting boots caked with mud, the pedals make more sense. Guys that hunt, farm or other industrial/commercial users, have different needs than you and I when we have our Florsheim penny loafers on commuting to work.

 

If GM were to offer more configurations, it'd raise costs.

 

You might look at just the gas pedal extension from this outfit.

 

If lateral spacing is still too large for your liking, you could have a clamp on steel piece made to extend the right side of the brake pedal. Or if you want to permanently modify it, have a piece welded to the pedal. But keep in mind you'd probably want to replace that modified part with a OEM part before selling the truck. The OEM brake pedal part is $65.

Miller%20pedal%20extenders_zpspj1bv4p1.j

Edited by spurshot
Posted

I'm 5'4" and find the pedal location and spacing no problem. But I've driven a lot of trucks, some medium and heavy truck also. I don't find the spacing any different than other trucks I've owned.

 

Agree with the post about the brake pedal feel on the truck. In the past i have always felt GM products were "under braked" not so with my 15 silverado. They feel strong and were strong when pulling a heavy load on vacation. Yes i have trailer brakes but the truck cab rear and bed were loaded with gear. Despite that i never had any brake fade on the downgrades. I always felt like there was plenty of pedal left. Just my .02. But GM got the brakes right on these trucks

Posted (edited)

Glad the PO figured out a solution, but this is something I had never thought of or considered.

 

I drove my GMT800 for 11 years without ever thinking about the pedals or spacing, and I jumped into my brand new 2015 like nothing had changed (drivability wise - but holy crap what a better truck!) So the spacing and depths are completely "normal" to me. I'm 5'8".

 

The brake pedal feel on my GMT800 was like a sponge. They have a very nice feel in the 2015. Firm, yet I don't feel like my face is going to go through the windshield if I hit them too hard.

Edited by 67ChevyRedneck
Posted

My GMT800 2500 had the best brakes I've driven. Very confidence inspiring. I do know the GMT800 1500 had puny brake calipers and rotors in comparison. I may be using my 2500 brakes as my reference on this 1500, which may be slightly unfair.

  • 3 years later...
Posted
On 8/5/2015 at 1:18 AM, bass mechanic said:

I have the same frustration, and for me it is a safety issue. any other vehicle has always had the pedals closer in height. the problem is I used to bump my foot on the brake when lifting from the gas. safety issue to say the least as in a panic maneuver I may not be able to get to the brake in time after another attempt.

so here is what I did for both my 14 and my 15

1. move the pedals all the way to the floor

2. disconnect the speedo cable that adjusts the brake height

3. move the gas pedal forward while the brake stays at the lowest position.

4. press memory button and hold the memory setting 1 or 2 depending on what driver preset you use until it beeps 2 times.

 

you'll find the truck a lot easier to drive and the throttle more responsive since you don't have to reach so far to press it and youll find the brake and gas are a lot closer to each other.

 

the only other option is to remove the brake pedal and find a way to bend it more straight. I am just waiting for someone to die because the brake pedal is positioned too high and the NTSB gets involved so GM will actually listen.

 

I've complained about this several times and even GM customer service from this forum suggested I contact my local dealer which I have done with no follow-up on their end.

 

I have a fix so my issue is resolved. honestly I don't know why anyone needs to move the pedals anyway. unless your wife is very short!

Hey Fellow Sierra Owners, 

 

First off, sorry to resurrect a dead topic. I just bought a new Sierra, and I really love the car except for the high brake pedal height Vs the gas pedal. 

I tired following Bass Mechanics steps, however for the life of me I cannot find the speedo cable that adjusts the brake height as mentioned in item 2. 

 

Best Regards,

  • 1 year later...
Posted

I agree with the op. When I'm driving my truck in the city for long periods of time, my right asscheek feels overworked from lifting so high to reach the brake pedal. Also my right inner thigh is a little sore almost like I have a knot in it. 

Posted

I agree with the op. When I'm driving my truck in the city for long periods of time, my right asscheek feels overworked from lifting so high to reach the brake pedal. Also my right inner thigh is a little sore almost like I have a knot in it. 

Posted

I agree with the op. When I'm driving my truck in the city for long periods of time, my right asscheek feels overworked from lifting so high to reach the brake pedal. Also my right inner thigh is a little sore almost like I have a knot in it. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,812
    Total Members
    8,960
    Most Online
    Artemis
    Newest Member
    Artemis
    Joined
  • Who's Online   4 Members, 0 Anonymous, 1,234 Guests (See full list)


  • Latest Articles

  • Posts

    • I don't drive this truck on a regular basis since I have a new company truck with no out of pocket fuel or maintenance cost. Yesterday I got it out to run some errands and got the title message on my DCI. A quick Google search suggested to first clean the Map Sensor. I pulled it out and it was sooty so cleaned it up and reinstalled it. Issue not resolved. My OBDII is a couple years old so didn't see any codes. Today I took it to a friend at AutoZone to get him to check it with his reader. It had the following codes: P20C3 P02BB P221F Stating the most likely solution is to replace diesel emission fluid (DEF) tank assembly.   So, I guess a trip to the dealer is necessary. I read where there was a backorder on these tank assemblies several years ago so hope that has been resolved.
    • Are you using a weight distribution hitch system with your trailer as that alone can change the actual tire pressure requirements needed. It would prove interesting to see what the actual individual axle weights are on your truck when you are hooked up to the trailer. In fact when your hooked to the trailer, typically if anything unless it has a large capacity weight distribution system that is over cranked, often the weight on the front axle will be less when hooked up vs driving empty and certainly if one doesn't have a weight distribution hitch. Really the only times one may get up there with weight on the steer axle is if there was a snow plow mounted on the front or a motorcycle on a rack or with a very large jockey tank full of fuel at the front of the box that transfers a bit of its weight to the front axle.    And of course your tires carry more weight for a given tire pressure due to their size vs a stock sized tire so there is that to take into the equation as well. 
    • Great info here thank you. I just joined, we have a 2014 Silverado truck we bought about 4 years ago with less than 5,000 miles on it. It has approximately 24,000 on it now. It appears to have all the standard issues that people are talking about. Occasional charging problems especially using 110 volt, occasional blinking triangle where nothing will turn on when first starting the truck but it will reset itself if you wait 10 to 15 minutes. Noisy coupler between the flywheel and the generator. Our truck is speed limited to 74 mph, is there any way to change that? The latest issue we have been dealing with is when driving long distance on the highway at full speed the generator does not keep the batteries charged. The meter will go into the yellow/red border Zone for charge status and the yellow triangle will illuminate solid but the generator will not keep the battery charged, not sure why the controller doesn't tell the gas engine to increase RPM to increase generator output it usually stays well below 25 kilowatts even though the battery is discharging and I have to slow down the highway to 45 mph and eventually pull over and let the truck idle to charge the battery so I can continue driving at speed. Has anyone had this issue before or have any idea how to diagnosed it? When via Motors was around it they were very helpful at troubleshooting. This becomes much if the Terrain is hilly and you're towing a small trailer
    • I have the GMC accessory (REV) cover installed by dealer. Ordered with the truck.  They did a very good install job, can't find a single issue. Some water gets in around the tailgate but no where else.  You can see daylight around the tailgate but that's not the covers fault.  Installation is means everything. Guys at my dealer were seasoned pros, not inexperienced here today good tomorrow types, like many dealers employ for these jobs.   I don't mind paying for a professional job.    
    • Like others have said, they will all leak. Mainly at the corners.   I have owned several and the best has been my current one. Revolver x4
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...