Jump to content

2016 GMC Sierra Denali lacking options/equipment?

Huss1301

Recommended Posts

StillOffshore Enthusiast

StillOffshore

Posted
Posted

 

Sorry, gonna disagree. No way you wil be able to swap over to push to start. First off, technology wise the parts list would be way more than anyone would be willing to pay, new door handles, fobs, proximity sensors and so on. Then 2 new fobs and keys, then parts inside of the truck like a new steering column and also trying to incorporate the switch into a dash no designed for it. Oh, don't forget the IP/dash wiring harness that isn't even setup for push button start.

Then factor in the calibration change, the BCM and any other modules. Those will never be able to be programmed at via the dealership, while the BCM can be programmed it isn't easy and that doesn't adderss the sub systems and or other modules that only the dealer can address.

 

And what you meant to say, was that it IS POSSIBLE, just doesn't make sense financially. ANYTHING can be done if you have enough money. Doesn't mean it makes sense. Dream big!!!

  • Replies 125
  • Created
  • Last Reply
Jim165 Enthusiast

Jim165

Posted
Posted

Didn't see it mentioned here, but does anyone find that the rear headrests are useless for the average adult? In my uncle's new Sierra, I was sitting in the rear and trying to adjust the headrests up...they only moved up about 3 inches and dropped right back down when I placed my head against it. Even in the top position, the headrest only came to the top of my neck. This has to be a safety issue, right? Won't my head can bash thru the rear window if we were rear-ended? Agree on the lack of a center headrest. Agree that the rear accommodations are steerage class at best.

Other thing: no telescoping steering wheel?

CRApex Enthusiast

CRApex

Posted
Posted

 

Other thing: no telescoping steering wheel?

 

My Denali has a telescoping column.

Jim165 Enthusiast

Jim165

Posted
Posted

 

Other thing: no telescoping steering wheel?

 

My Denali has a telescoping column.

 

Sorry CRApex, should've specified that he has an SLE, so the tele wheel is not germain to the Denali discussion. Strike that comment..

redwngr Senior Enthusiast

redwngr

Posted
Posted

My Denali has a telescoping column.

 

Sorry CRApex, should've specified that he has an SLE, so the tele wheel is not germain to the Denali discussion. Strike that comment..

FWIW, telescope is available on SLE and standard on SLT and above.

 

(and yes, isn't a Denali issue)

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Deadwood
      primary drive belt tensioner

      By Deadwood · Posted

      I bought belts and pulleys for my '20 L5P at Rock Auto a couple years ago. I have used them for many years, and almost always save significant money, especially when I buy maintenance stuff ahead of time.   They carry many OEM parts, which is all I use unless an aftermarket is shown to be same/superior, or if it is an insignificant part or unavailable OEM part anywhere else. RA is usually lower priced, often by a bunch, but parts are sometimes unavailable or out of stock, and I do shop around and sometimes find better prices at other sites.   Be aware that you pay shipping, and if you buy multiple items and they are coming from different warehouses, the shipping can kill the advantage. Planning ahead is best if possible.   If you have a transmission service in the near future, check out their OEM (AC Delco ULV) fluid, usually MUCH less than anywhere else.
    • Deadwood
      10L1000 anyone with High Mileage ? I hate Damocles....

      By Deadwood · Posted

      New member here, very long time occasional guest. Saw this thread, thought it would be a good time to contribute someting. It is only my experience and not a claim that everyone will have the same.   I bought my '20 3500 L5P new and have put 99.9% (literally) of it's current ~400k miles on it myself, with over 50% of that towing loads between 4k to 15k, and to me this truck has been nothing short of amazing. For the first 235k I had zero issues, and from there until 321k I replaced a NOx sensor, two failing glow plugs, and three of the notorious injector connectors. I believe this truck is in part, a testament to good luck, but also good care and following a decent maintenance schedule (I also keep meticulous records.) As a result, it looks as good as a well cared for 70k rig, up and down, inside and out.   At some point before that 321k mile mark I began to get a little spooked about the 10L1000, especially the valve body. Word of mouth about potential issues prompted me to jump on the net to sift through all the noise and determine what all the fuss was about. I routinely take long trips, coast-to-coast and points in between, so roadside breakdowns can be '...a thousand miles from nowhere' and a bit of a challenge, and though I had no issues, my guard was up and activated.   And then I stumbled across a chance to salvage some parts off a new 2025 that had been wrecked in transport. I grabbed a few wear items (alternator, pulleys, etc.) and on a whim asked what the ten speeder would cost me. It was cheap...really cheap. I knew some changes had been made in the '24+ version 10L and were supposedly not compatible, but I called service/parts at my local Chevy dealer and asked why and they didn't know. A call to a well known aftermarket transmission outfit revealed it was very likely it would be fine, but to them not 100% sure.   Because it was cheap (really cheap) and I was spooked, I took the chance. Had it installed by a local shop and it worked like a champ, shifted just like the original. At it's first service at 37k, I had the shop put in a Next Gen valve body kit, which after some initial hiccups and rough shifts, smoothed out though with somewhat firmer shifting.   All that said, I have a very serious concern about my newer transmission as just two weeks ago it suddenly began to exhibit a strong reluctance to engage forward or reverse. It was a bit past due anyway so I took it in for service. The reason it was sticking was due to 'glitter' in the fluid clogging the filter...not good folks, often indicates a converter giving out. We ended up going ahead with the new filter and fluid, first to see if it would move and shift, and then if so buy me a little time. It did, and I've driven it over a thousand miles and it is shifting smooth, no noises or slipping. Regardless, it looks like a third gearbox is in my future so I can resume taking long trips with some confidence. In the very short term, my curiosity will have me examining the fluid to check how much glitter has reappeared.   An earlier poster had alleged, in the context of 10L100 failures, that it is another example of how we seasoned citizens somehow descend into hysteria, lose control of our senses, and react irrationally after brief encounters with the idiocy of the internet infosphere. Let me say (and I have used and abused said internet since it's infancy) there is no segment of the populace that has a corner on over-reaction to digital garbage. Just as my offering of experience in this arena is purely anecdotal and should not be considered gospel or all-encompassing, I believe it is still worthwhile information to consider, along with other relevant anecdotal experiences about things like complex transmissions, especially when balanced with other sources.   So to answer the original question, yes I got high miles out of my first 10L, trouble free for 321,000. Now I really wonder how much longer it would have went. Did I 'overreact' to the internet ghouls by replacing a 'good' one with a 'bad' one? Maybe. Who knows, the thing might have taken a puke a 100 miles later. So I'll just fix it again, then move on and start thinking about all the other stuff that will eventually wear out. It still has the original brakes (they're at ~60%), original injectors/pump, turbo, water pump, etc....pretty much original everything. Knock on wood.
    • swathdiver
      6 Speed vs 8 Speed

      By swathdiver · Posted

      At peak temperature.  They get to cool down and warm up more, especially those with the external cooler.  I have three GMT900s and one of them has over 225K on its original transmission.  Fluid gets changed about every 36K miles, all of it.     It's not the bean counters, it was the government.  They had to meet CAFE standards and other government requirements.   To get around that, we tune them and modify them to our liking.
    • GMCustomerService
      Will not stay in Reverse

      By GMCustomerService · Posted

      Our customers' safety isn't something we take lightly. To ensure you get the proper assistance for your truck's repairs, please fill out the form at https://s.chevy.com/support-request with all pertinent details including your username.
    • GMCustomerService
      2026 Z71 Forward and Rear Park Assist help

      By GMCustomerService · Posted

      We appreciate you sharing your experience with your truck. To ensure we get you the proper assistance, please fill out the form at https://s.chevy.com/support-request with all pertinent details including your username.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...