Jump to content

2017 Sierra 1500 Winch Mount Options?

Andrew Branch

By Andrew Branch
in Modifications & Accessories

 Share

Recommended Posts

Andrew Branch Enthusiast

Andrew Branch

Posted
Posted

Are there any options for a hidden winch mount or a brush guard / winch mount that utilize the factory bumper for a 2017 Sierra 1500? I've found several options for the 2014/2015 but nothing for the 2016/2017.

crankman Enthusiast

crankman

Posted
Posted (edited)

Andrew does your truck have the license plate spot in the front bumper? I put one on my 2011 Silverado built it with 1/4 angle but later Rough Country came out with the same style set up. Uses the license plate area for the rollers. Im guessing you looked there? I picked up a plate of my liking and bought a clamp kit on ebay that you put a license plate on and it snaps on the rollers. Just noticed were both in LR. Cool If you really want to do it find a 2013 and measure between the frame and compare to yours. If its the same you could use the rough country kit. There kit says it goes from 07-2013.

Edited by crankman
  • Like 2
Andrew Branch Enthusiast

Andrew Branch

Posted
  • Author
Posted

Andrew does your truck have the license plate spot in the front bumper? I put one on my 2011 Silverado built it with 1/4 angle but later Rough Country came out with the same style set up. Uses the license plate area for the rollers. Im guessing you looked there? I picked up a plate of my liking and bought a clamp kit on ebay that you put a license plate on and it snaps on the rollers. Just noticed were both in LR. Cool If you really want to do it find a 2013 and measure between the frame and compare to yours. If its the same you could use the rough country kit. There kit says it goes from 07-2013.

Thanks - I'll definitely check it out. I really wish somebody would develop a kit for this - I'll gladly throw $$ at them.

 

 

Sent from my iPhone using Tapatalk

  • 2 weeks later...
  • 1 month later...
  • 1 year later...
Will O'Daniel Enthusiast

Will O'Daniel

Posted
Posted (edited)

Here is mine. I will be posting more pics in the next few days with the brackets I built and plate setup. No one makes a bracket for a hidden winch because of the tow hook bolt placements. All brackets and plates were made of 1/4 inch steel. I did have to drill one hole and run a 4 inch bolt through the passenger side frame, rear hole of the tow hook for the bracket bolts. I also had to cut off the lower front bumper brackets. The winch was to wide to sit between them so they had to go. The last major mod was the lower facia being cut. The fairlead sits right below the metal of the bumper and I cut out the plastic of course. I also cut the plastic to fit a receiver and we welded a small piece of angled steel to the bottom of the winch plate and used the original screws and retainer nuts for the facia bracket. Last, Oregon requires a front license plate. So I used 1-1/4 conduit holders, drilled holes in the license plate and original plate bracket, and it just simply snaps onto the fairlead. Completely hidden. Winch is a Badlands ZXR 12,000 with wireless remote. I am unable to to to the spool lock, so no free spool for me on this setup unfortunately. I also ran quick connects 1/0 AWG wire to both front and rear of the truck. I will also be doing a hidden winch on the rear factory bumper of the truck in the coming weeks.

A028CB3C-9F0B-45FA-8B12-A704C3B826FB.jpeg

702CE758-F519-47D3-806E-D45A6980DD3F.jpeg

53B22DF3-14A6-4A54-A3A4-F00D4575BD08.jpeg

Edited by Will O'Daniel
Will O'Daniel Enthusiast

Will O'Daniel

Posted
Posted (edited)

Driver side bracket. You can see that the bracket hugs the frame. You can also see that the bracket drops 1-1/4 inch and pushes forward so the the plate can clear the complex angles of the plastic facia. The passenger side is a mirror of the driver minus the extra hole for the to seat the inside bracket to the frame. 

F9F50094-0C1F-475E-A151-61D63A7817A7.jpeg

97DB0CD9-5308-453C-946A-44E968BBF6C5.jpeg

Edited by Will O'Daniel
Will O'Daniel Enthusiast

Will O'Daniel

Posted
Posted

Passenger side bracket. You can see the “odd” bolt that we used to pass through the back of the tow hook. This is a 4” bolt. We bored out the threads on the back of the tow hook so it could pass through and drilled a hole in the frame on the other side. This is the only frame modification needed. 

C34F73D0-A3FE-46BC-9AF5-27E99372C18D.jpeg

3AFE16D5-6456-499C-BF74-885B56FCB60D.jpeg

  • 3 years later...
CadillacMac New Member

CadillacMac

Posted
Posted

Have you guys found the Rough Country Hidden winch mount?

 

https://www.roughcountry.com/gm-hidden-winch-mounting-plate-11004.html?find=2017-gmc-sierra-1500-4wd-739475&sid=IyuyamO9di

 

I do have a few questions about it if anyone's installed it. Do you have to relocate the control box with this? Do you reach through the hood to disengage the clutch?

 

Thanks!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      So, do I go elbow-deep on this thing or list it for sale and play dumb? Seems to "runs good."   I'm about $1200 away from having: -a rebuilt injector ($300) -a new cat ($250) -a new cat back exhaust (OE style) ($300) -a new AC compressor ($200) -AC refrigerant charge ($150)   In theory, this should rectify the obvious detracting issues from its value and operability. Cold AC with a non-squeaking AC pulley both sounds and feels good. An exhaust that isn't cut/hacked in 17 different places and doesn't vibrate on a crossmember would make it sound and feel less janky. A working cat would help the stink, and will save the earth, but *if and only if* the fuel system is working properly, which would also address the intermittent "rich" CEL.   Heard a good one... CEL for "Rich condition" means you haven't spent enough money on the truck lately, and it's letting you know.   Rebuilding the injector would seem to be the most important part. Replacing the cat would be secondary. I don't think mine is plugged or overly restricted, but it might be a little restricted? I have no good way to tell other than seat of the pants feel. I hate the smell.   The current theory is I have a rich idle problem: A bad fuel pressure regulator, or a leaking injector(s) being the highest probabilities. I already replaced the FPR but that doesn't mean its replacement isn't also bad. It was a new part from Dorman, but the packaging looked like it had been sitting on a shelf for 20 years.   This is the (single) upstream O2 sensor shown at idle. I'm getting a lot of "rich" it seems. Sometimes it stays high like that and doesn't drop down. That makes me think it's processing injector leaks or a partially stuck open injector.     Other times it looks like this. Nice oscillations between rich and lean, which is what I think it should be. Under load and at speed, the oscillations are nice and tight and uniform looking, high and low.     Fuel trims suggest the PCM is compensating pretty hard at idle to pull fuel out. But it's not enough to trip a CEL. Something about slowing to a stop: brake vaccum booster, EGR, or the EVAP purge is delayed, or there's pooled fuel in the intake again that's draining into a cylinder is enough to set the CEL. Of course, in two days of driving, it hasn't set. I was hoping to actually look at the freeze-frame data when it sets. IAT is high because it's idling on an 83 degree day here.  
    • Another JR
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By Another JR · Posted

      Have considered installing a DC to DC charger in your camper to replace your isolator?  
    • newdude
      Gas fill door

      By newdude · Posted

      Common failure.  You need to replace the fuel door housing.   The painted cover transfers over to the new housing.  To remove the old one there is 4 spots where you poke the plastic to release it.  
    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...