Jump to content

2004 6.0 Rough Idle and hard starts when cold

smee907
 Share

Recommended Posts

smee907 New Member

smee907

Posted
Posted

Hey guys, I recently picked up a 2004 GMC Savana Quigley 6.0 with about 183k miles. It has a couple issues that I was hoping other guys would have some good advice on.

Its hard to start cold and has to be kept running for a few minutes before it will idle on its own. After that, it has a low idle and can stall if you're steering in a parking lot and get off the throttle too suddenly. The last issue is that when you come to a stop like at a light or stop sign, the voltage will drop from around 14 to about 9 then take several seconds to climb back up to 14 again. There is no check engine light, and I can't pull any codes with my cheapo scanner. The service light comes on for a short time when it first gets started. It runs good aside from those things. It has plenty of power, and

 

I did some research and read up on other guys with the same and similar issues, but so far haven't found the cause of mine yet.

 

I cleaned the MAF with CRC MAF cleaner which was actually pretty clean. I noticed that 2 of 3 bolts were missing for holding it onto the air box, so I replaced them. Cleaning the MAF made no improvement.

 

I cleaned the throttle body which was also pretty clean. There was some buildup on the throttle body around the butterfly valve, so I cleaned everything off thoroughly with q-tips and CRC Throttle Body Cleaner. I had unhooked my battery before unhooking everything for the throttle body, and I thought everything was fixed after hooking it all back up because it started great and idled perfectly afterwards. I took it for a drive and the voltage stayed right at 14 and didn't drop with the stereo, headlights, front heater, and rear heater all running at the same time when I came to a stop.

 

I started it the next day before having to go somewhere and it had the same issue again. I figure the battery reset the problem until it was run and shut back off again. I unhooked the battery before having to leave about an hour later and it confirmed it. It started right up, and ran perfectly for my 35 mile drive without low idle or voltage drops.

 

My last initial thought was needing an intake manifold gasket, but I'm still not getting any codes, and I would imagine that it would still run bad even with the battery reset like that. I've heard of people having their ECM firmware updated and fixing their problems, but don't want to throw money at the dealer. I can have my intake manifold gasket done, but don't want to throw money at that either if its not the problem. I did have a guy recommend getting a coolant temp sensor because he had a similar issue on a Ford, and I think I remember reading that a couple guys with 6.0's had the same type of problem with theirs and fixed it with the coolant temp sensor as well.

 

I wanted to see if anybody on here had some good advice to give before I do anything else because the next things to throw at it won't be as cheap as the rest. Thanks, and sorry for the long post...

 

Tom

 

Podor Enthusiast

Podor

Posted
Posted

Is it throttle by wire or does it have an actual throttle cable?

Podor Enthusiast

Podor

Posted
Posted

It sounds like the IAC motor is not controlling the idle. GM vehicles usually don't set a code for IAC issues. The Idle Air Control motor is a stepper motor that controls air flow through a port in the throttle that controls the idle. The port may be clogged, the motor may be defective or there could be a wiring issue. There are probably 2 torx screws holding it in on the side of the throttle body. There is a cone shaped plunger with a spring on the back side. The motor pulls the cone away from it's seat to raise the idle by creating a controlled vacuum leak. Make sure there are no deposits on the cone an make sure the port is clean. If it looks OK or doesn't fix the issue, most likely the motor itself is bad. Super easy to replace, just make sure to hold on to the screws.

  • 2 weeks later...
smee907 New Member

smee907

Posted
  • Author
Posted

Update: I just got a replacement IAC valve and installed it, so I'm going to monitor it for a few days.

  • 4 years later...
Shawn2021 New Member

Shawn2021

Posted
Posted (edited)

Mycar is fixed now 😀, I had the same issue, I replaced with another used  throttle body , It's fixed now, the problem is Idle Air Control  ,this one is selonoid that controls idle,

if this selonid is not working properly , youu wont notice , because does not throw any engine code.

2021-08-30 16.27.34.jpg

2021-08-30 16.27.23.jpg

Edited by Shawn2021

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Another JR
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By Another JR · Posted

      Have considered installing a DC to DC charger in your camper to replace your isolator?  
    • newdude
      Gas fill door

      By newdude · Posted

      Common failure.  You need to replace the fuel door housing.   The painted cover transfers over to the new housing.  To remove the old one there is 4 spots where you poke the plastic to release it.  
    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      I have an observation and a question... 1) I watch the voltage closely because I have had to dial in the cut-in/cut-out voltages of the battery separator to my camper.  The "smart" charging drives me nuts.  Anyway, I noticed that when coasting for a while, and especially if lightly using the brakes (though not necessary), the voltage goes up from mid/high-13 volts to mid/high-14 volts.  Then it drops back down after stopping or going again.  Consistently!   The only explanation I can come up with is REGENERATIVE BRAKING!  Well, maybe that's a little bit of an exaggeration, but it's certainly free extra battery charging.   2) Driving on mountain roads I will use L and vary the max gear.  Things straighten out and I end up in L10.  Sometimes I leave it there for a while.  Is there any difference between L10 and D?   

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...