Jump to content

6L80E bypass valve mod

AZ_SS

By AZ_SS
in Engines & Drivetrain

Recommended Posts

AZ_SS Enthusiast

AZ_SS

Posted
Posted

Does anyone make the bypass block without the thermostat? I have seen online how you can modify the bypass to have it flow constantly through the cooler but I would rather buy one built to not bypass.

AZ_SS Enthusiast

AZ_SS

Posted
  • Author
Posted
5 minutes ago, imiller1974 said:

Several companies make them, you can find them on Summit, Jegs, and Amazon. BUT, all the ones I've seen have either threaded holes, -6 AN fittings, and you'd have to change or modify you're lines as well.

Below is an example...

https://www.amazon.com/LSX-Innovations-Cooler-Manifold-Fitting/dp/B07D9T734Z

I must have been searching all wrong. Thanks

  • 2 weeks later...
14 gmcl83 Enthusiast

14 gmcl83

Posted
Posted

On YouTube is a video of how to remove it I did it on my truck a while ago temps

never go over 175.

M-Wheeler Enthusiast

M-Wheeler

Posted
Posted
On 11/13/2018 at 5:13 PM, AZ_SS said:

I must have been searching all wrong. Thanks

are you talking about a total removal of the thermostat block etc. If so, please provide link to the video. I have seen the video of retrofitting the block with a 1/4" plug, but not removal of the entire block.

AZ_SS Enthusiast

AZ_SS

Posted
  • Author
Posted

Those are the only videos i have found to. That's why I was asking about a replacement block not retrofitting s stock piece 

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • bwiese
      upgrading speakers on 2026 std cab WT...

      By bwiese · Posted

      I don't wanna do major surgery/upgrades, behind-the-dash work, add amps, change radio etc. on my '26 std cab WT. On the WT, it has the base 7" IOR infotainment setup, and only two speakers (doors). Since I listen to classical, looked around for speakers that do well and dug thru reviews. Two-way speakers were found to be better than 3-way. So I've ordered a pair of  Infinity Reference REF-9632IX 2 way speakers.  [These may  or may not have been discontinued / succeeded by the 3-way ...9633 ones.]    These speakers are lauded for 3 ohm and 94db sensitivity spec so they'll work well for ordinary base car radios without amps and offer better performance (quality,  strength) than  default base paper-cone speakers. They'll be installed in a few days and I'll let y'all know what I think. Bill W San Jose      
    • RyanbabZ71
      RyanbabZ71's 2019 High Country

      By RyanbabZ71 · Posted

      Thanks!   Changed out the rear shocks today to Bilstein 5100s.  So far feel much better. The stock Rancho were wore out.  Lots of heavy hauling (2 moves, home renovations, etc).  Next up is new BFG tires Monday.  Cant wait the current tires have little to no wet traction and are super loud (hum)    
    • Snowcamo
      No high speed fans...

      By Snowcamo · Posted

      Ok, I got the all the codes. What do you all think would be a place to start?
    • Chuck FB
      Correct way to service 2024 l8t allison trans?

      By Chuck FB · Posted

      How about I just point to the factory pans stand pipe little drain plug and claim its a pan with a real drain plug !. I just couldn't swallow the fact that a Dorman pan which at this point is probably the only pan out there that fits the gas version truck cost that much up here in Canada so I decided initially anyway to skip it and see what I thought of pulling the pan method and down the road if I felt inclined enough then I would either install a drain plug kit in the factory pan if there is enough room for it, or have a bung welded onto it, or put an aftermarket pan on. The thing is if the pan is not pulled then the magnets in the pan can't be inspected and cleaned or if wanting to change out the filter. However of course it certainly would make the job easier to be able to drop the oil first before having to handle the pan if dropping the pan that go around was the goal.    I knew a guy locally that was doing custom field spraying years ago with a pickup pulling a ground driven sprayer, I believe it was a GM pickup with an automatic trans. He had a drain plug in his pan and would drop the oil out of it once a week and top it back up through the dipstick tube to keep refreshing a portion of the oil often and that made the transmission last far longer than had he done nothing. Soft fields pulling 500 gallons of water at the start of each mixed up sprayer tank batch and in low range sucking along. I imagine he got some tips from other custom sprayer outfits doing the same thing at the time and learning from their blown up tranny mistakes. Transmissions then had no lock up converter so would cook the crap out of the fluid slipping that much and it would not have been synthetic fluid either. 
    • KARNUT
      Gas Prices

      By KARNUT · Posted

      3.39 Kroger’s in Montgomery Texas. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...