Jump to content

Interior swap

08gmc17
 Share

Recommended Posts

  • Replies 84
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

08gmc17
08gmc17
Andrew_01
Andrew_01

Did you end up finishing this swap? Would love to see the finished product. Also, what paint did you use to paint the interior and did it flow with the high country interior? 

08gmc17
08gmc17

Posted Images

  • 3 months later...
shakenfake Senior Enthusiast

shakenfake

Posted
Posted
16 hours ago, DeeGloGang said:

I have a 2008 Chevy Silverado 1500. Would the front seats from a 2014 Silverado 1500 fit ?

You would need to create new seat brackets. It would be near impossible to get the seats to work with power though.

  • 2 weeks later...
Yount166 Enthusiast

Yount166

Posted
Posted

Hey all, Idk what happened to the original user who made this thread, and hopefully all is well. But I was just browsing through this because I already started doing this to my 08 2500. At least the seats, carpet, and center console for now. But I figured I’d post some pics and maybe a short video showing how I made all the seat brackets work. 

  • 2 weeks later...
  • 2 months later...
xKingdom Enthusiast

xKingdom

Posted
Posted (edited)
On 1/26/2022 at 9:49 PM, Yount166 said:

6330EAF9-ECD9-4D03-A629-D2E1BE5AF53F.jpeg

3207F09B-2B38-4B2A-B48B-C100BD90D1D6.jpeg

What fabrication had to be done? I'd like to do this with my lanche'

 

Does the power work?

Edited by xKingdom
  • 2 weeks later...
Yount166 Enthusiast

Yount166

Posted
Posted
On 4/27/2022 at 10:54 AM, xKingdom said:

What fabrication had to be done? I'd like to do this with my lanche'

 

Does the power work?

For the back seats, —- nothing, it’s all unbolt and bolt. 
 

for the front I had to cut the old brackets off the 07-13 seats and cut the 14-18 brackets off. And weld the old mounts onto the new tracks. (Careful to not weld the sliding tracks together). Then due to the design of the seats I made brackets out of ar500 plate to basically set my seats back about 6 inches. The new rails are shorter than the old ones. (I’ll post pictures here for you to see.) I haven’t came up with new shrouds to hide all this yet but have a couple things in mind. 

 

 

— as far as the power goes I have the passenger side working and the driver side working as well with all the basic movements. But I’m currently working on cross connecting the 30pin harness to the 48 pin harness now. If I can get it all done I should have all the heated seats and factory functions working through factory buttons on the dash. But it’s being a nightmare finding a diagram on the new seats. I have all the old harness wires figured out. 
the issue is with gm, they have the brain in the seats and if it’s not done correctly and where they talk then you get a Christmas tree on the dash. And or worse you pop the airbags in the new seats. (I suggest disconnecting these). 

B2A9D721-F717-4DFD-AB14-8DE5ECD06A3F.jpeg

image.jpg

image.jpg

image.jpg

Yount166 Enthusiast

Yount166

Posted
Posted

Couple more pics here. Just how to unhook the airbags in the seats and one of the seat belt tensioner that can be removed when retrofitting. Your 08-13 seatbelt will bolt in as well, just you have to turn the locking tabs until you find a spot where it tightens down flat. (Not perfect fit but will work fine) .

 

I’ll try and keep posting updates on the truck as I go on but due to work it’s hard for me to actually get anything done on the project!

ABCA3F5A-498D-4674-ABBE-C0715A89C65D.jpeg

07E32EE9-8405-48A7-8427-8DFBFA46908A.jpeg

xKingdom Enthusiast

xKingdom

Posted
Posted
On 5/8/2022 at 12:54 AM, Yount166 said:

Couple more pics here. Just how to unhook the airbags in the seats and one of the seat belt tensioner that can be removed when retrofitting. Your 08-13 seatbelt will bolt in as well, just you have to turn the locking tabs until you find a spot where it tightens down flat. (Not perfect fit but will work fine) .

 

I’ll try and keep posting updates on the truck as I go on but due to work it’s hard for me to actually get anything done on the project!

ABCA3F5A-498D-4674-ABBE-C0715A89C65D.jpeg

07E32EE9-8405-48A7-8427-8DFBFA46908A.jpeg

YES! please keep me posted I'd like to do this swap in my avalanche but the wiring is the part I'm worried about.

  • 4 weeks later...
Yount166 Enthusiast

Yount166

Posted
Posted
On 5/9/2022 at 11:05 AM, xKingdom said:

YES! please keep me posted I'd like to do this swap in my avalanche but the wiring is the part I'm worried about.

Little update, I had a day to try and work on the truck when I got back from being out of town for work. Ran into some issues, after getting the driver seat to power up and move, a couple functions were not working properly, (the seats came from a wrecked truck). The driver seat had a bad switch panel, and a bad motor. Ordered those and got them put in this last weekend and then found that another motor is not working due to a bent bracket. So I’m back out for work again but I will try to resolve the issues on my upcoming vacation and post another update. Thanks 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • fm2176
      New to Me 2010 SLE (Quirks, Issues)

      By fm2176 · Posted

      Thanks!  I figured as such; GM and other manufacturers have used standard parts and harnesses across trim levels and such for decades.  I pulled the blank accessory cover off of my commuter van (a 2016 or so Chevy 15-passenger) years ago and found the plug for a USB outlet.  It wasn't connected to anything, though (I tried swapping in an outlet from another van).  I was a GM Tech years ago (late-90s) and was pretty familiar with my 2006.  I might be wrong, but I view newer vehicles (pretty much anything made in the past 20 years) as being a lot more plug and play.  Meaning, more unused wires and plugs unless you have the Mack Daddy of vehicles.    
    • Coastie05
      It's Been a Long Time...

      By Coastie05 · Posted

      Welcome back!
    • davester
      New to Me 2010 SLE (Quirks, Issues)

      By davester · Posted

      not all plugs will be used.  gm uses more generic harnesses that support most/all options, and if your truck doesn't have a specfiic option, the plug won't be used (commonly will have a dummy insert in the plug , or it'll be taped up, but some may just be left as is).  But it's sldo possible some p.o. has installed the wrong/cheaper parts that aren't correct for your vehicle...
    • fm2176
      New to Me 2010 SLE (Quirks, Issues)

      By fm2176 · Posted

      First off, I'm not trying to just get easy advice/fixes for the issues I've noticed so far.  I'll be combing through the site via searches and such, and if past experiences are any indication, should find what I need.  For the sake of conversation, though, I figured I'd post the handful of things I've noticed in the 12 hours since buying my 2010 SLE CCSB.     Indicator lights: Airbag and TPMS.  The tire pressures aren't reading for any of the wheels, so I'm pretty certain the sensors were either removed, are damaged, or are otherwise inoperable.  I used to mount and balance tires 25 years ago but am pretty much ignorant when it comes to TPMS.  My 2006 didn't have the sensors and this might be the fourth vehicle I've owned that does.     Radio: Rear speakers aren't working.  I removed the driver's side rear door panel and checked the speaker and wiring.  I also removed the sill and b-pillar covers to check the wiring.  A few minutes of Google Fu showed that this is potentially a head unit issue.    Switches: Power mirrors don't turn left/right.  I ordered replacement driver's door switches that should arrive tomorrow.  The windows and locks work but it was only about $20 for all of them.  The driver's side rear window switch lets the window down but won't put it back up.  I think the passenger rear doesn't work at all.  In the coming days/weeks, I'll break out my multimeter to check all of that.   Unknown wiring harness: There's a box attached to the front driver's side of the engine compartment, right where the second battery shelf is located.  There are three plugs, one of which looks like it fits a standard headlight-style bulb (9007 or similar).  It doesn't look like it's plugged into anything.  I'll do some digging and if I don't see anything elsewhere on the site, post some pictures here.   Unknown plugs on brake booster: There are at least two female plugs on the brake booster that aren't being used.  I think it might be a replacement/aftermarket, so maybe those are used for a different application, as there don't seem to be any unplugged harnesses and no indicator lights are on.   Little squeaks when turning: Sounds almost like a bushing around the bed of the truck.  I'll have to pay close attention as I get more familiar with the truck.   Clunk on acceleration: possibly the infamous drivetrain clunk.  My 2006 had it and I'm just not familiar enough with this truck yet to fully grasp what it is.   Anyway, my apologies for the vague and all over the place post.  This truck is new to me, and it's been four years since I drove my 2006.  With 200k miles, I know I'll need to learn this truck quickly to avoid having any major issues, despite being confident it's got much more life to it.  My 2006 had nearly 320k on it when I parked it (nearly 300k of which I put on the truck), and it was still drivable then, though I suspected the head gasket might have blown.  I'd hoped to have that truck back by now, but it's gone forever, as I detailed in my reintroduction thread.  
    • lowrider
      Range RA007 DFM Module

      By lowrider · Posted

      I always drive in Sport mode. With more driving, I am finding the initial response when accelerating is much quicker now🖕 Lou

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...