Cargo lights when unlocking with FOB

SS502 · January 2, 2019

20 minutes ago, DenaliDH said:

What is the diode for in the gray connector on the left?

Edited January 2, 2019 by SS502

pgamboa · January 2, 2019

Left diode is for puddle lamp (on DL3 Mirrors) to follow interior dome lamps. This is a requirement for 2014 trucks that upgrade from DL8 Mirrors to DL3 Mirrors.

Sent from my iPhone using Tapatalk

SS502 · January 7, 2019

I wanted to share what I found...this mod is awesome but my first choice of diodes was not. I ordered the right diodes but the first ones I ordered has a wire so thin it just slid right on through and didn’t seem to make contact...the second batch has a much thicker wire and worked perfectly. I’m not saying the thin won’t work but I don’t think they would have stayed in place even if I could get a good contact.

Bengalman21 · January 12, 2019

On 12/28/2018 at 10:17 PM, pgamboa said:

Need a diode to have your cargo lights follow the reverse lights.

Sent from my iPhone using Tapatalk

Same diode for fog lights that’s with high beams on? Better photo of exactly where it needs to go?

TIA

pgamboa · January 12, 2019

Same diode for fog lights that’s with high beams on? Better photo of exactly where it needs to go?
TIA

Yes. If you zoom into the pic, it’s the top slot, and two slots down from that one.

Sent from my iPhone using Tapatalk

4weight · January 12, 2019

On 1/7/2019 at 3:24 PM, SS502 said:

I wanted to share what I found...this mod is awesome but my first choice of diodes was not. I ordered the right diodes but the first ones I ordered has a wire so thin it just slid right on through and didn’t seem to make contact...the second batch has a much thicker wire and worked perfectly. I’m not saying the thin won’t work but I don’t think they would have stayed in place even if I could get a good contact.

That’s exactly the problem I had, my first order of diodes simply were so thin it would not make a good connection. So the Chanzon were the ones that worked correct? I will give these a look. Thanks !

Edited January 12, 2019 by 4weight

SS502 · January 12, 2019

2 hours ago, 4weight said:

That’s exactly the problem I had, my first order of diodes simply were so thin it would not make a good connection. So the Chanzon were the ones that worked correct? I will give these a look. Thanks !

Yes Sir, nice and sturdy...Chanzon ?

PM me your address and I’ll send you a few of them. I needed 3 (not 3 for the mod, I ruined 2 of them) just because I kept bending them too much, finally did use needle nose and that worked much better but I’ll send you like 10 of them on Monday.

Edited January 12, 2019 by SS502

sgand · January 18, 2019

On 12/28/2018 at 11:17 PM, pgamboa said:

Need a diode to have your cargo lights follow the reverse lights.

Sent from my iPhone using Tapatalk

I must be blind, I cannot find where this is located.

CovetedStyle · January 18, 2019

6 minutes ago, sgand said:

I must be blind, I cannot find where this is located.

Under the dash driver side

pgamboa · January 18, 2019

I must be blind, I cannot find where this is located.

No worries. I get asked this question all the time.

Sent from my iPhone using Tapatalk

r1mechanic · January 18, 2019

No worries. I get asked this question all the time.

Sent from my iPhone using Tapatalk

I had to sacrifice a diode for its wires and solder them to the one I was using for the jump and it worked a lot better for me. Bifocals suck sometimes!

Sent from my iPhone using Tapatalk