Jump to content

Door ajar sensor issue?

AlanD_M97

By AlanD_M97
in Troubleshooting & Recalls

 Share

Recommended Posts

Jack Daniels New Member

Jack Daniels

Posted
Posted
On 11/28/2023 at 10:40 AM, mikeyk101 said:

So what did you find when you checked the wiring? Were there any broken or chafed wires where wiring passes out the door to the connector?


I couldn’t find anything inside the truck shorted, open, or chafed.  I didn’t even bother with the outside because by that point the issue stopped and failed with the door closed position and I was beyond fed up with it.

 

That said, I didn’t spend an absolute ton of time checking wiring inside either.  Quick inspection of the accordian harness in drivers door and the door with the issue.  Pulled the accordian back, spread the wires apart looking for anything obvious.  Checked the pins against ground, looking for shorts, looked for recessed pins, etc.  

 

Removed the door panel, rinse lather repeat, looking for obvious issues.  Found nothing.

 

I read on another forum that there’s circuitry that passes through the door latch mechanism, so I replaced it out of desperation.  No joy, that didn’t solve anything either.

 

I hooked 12v directly to the window motor to see if that maybe had issues because the same door that has the ajar issue, well that window doesn’t work either.  Window motor worked great.

 

I still believe it’s wiring related though because how haywire my truck went during that rainy spell.  Then when the sun came out, the issue went back to its normal intermittent self. (Then later failed completely)

 

Maybe I’ll see if I can get my hands on some wiring diagrams.  Or sell the truck. Who knows.

  • Like 1
Jack Daniels New Member

Jack Daniels

Posted
Posted (edited)

FOUND IT

 

So since my passenger/right rear door was the main problem child, (window not working and door ajar) I decided to deep dive into that door.


 I removed the door panel, disconnected the accordion from the pillar, disconnected all plugs from locks, window button, speaker, crash sensor, etc.  and I pulled the entire darn harness out of the door completely.  Quick inspection of the overall harness… looked great.  Then I said screw it and I cut the accordion boot clean off, then cut the tape that the wires are wrapped in underneath that same boot.

 

BAM!  The wires were soaking wet (it hasn’t rained here in weeks), broken, and corroded.

 

Looks like I’m headed to the stealership tomorrow for new harness.  I’m an avionics technician so I would just repair those wires… but I had a fit of rage and cut the boot off.  Damn.

IMG_5226.jpeg

IMG_5228.jpeg

IMG_5229.jpeg

Edited by Jack Daniels
  • Like 2
MikeBMW Senior Enthusiast

MikeBMW

Posted
Posted
2 minutes ago, Jack Daniels said:

FOUND IT

 

So since my passenger/right rear door was the main problem child, (window not working and door ajar) I decided to deep dive into that door.


 I removed the door panel, disconnected the accordion from the pillar, disconnected all plugs from locks, window button, speaker, crash sensor, etc.  and I pulled the entire darn harness out of the door completely.  Quick inspection of the overall harness… looked great.  Then I said screw it and I cut the accordion boot clean off, then cut the tape that the wires are wrapped in underneath that same boot.

 

BAM!  The wires were soaking wet (it hasn’t rained here in weeks), broken, and corroded.

 

Looks like I’m headed to the stealership tomorrow for new harness.  I’m an avionics technician so I would just repair those wires… but I had a fit of rage and cut the boot off.  Damn.

Whoa, nothing like the nuclear option.
Gotta look for where the water got in first, or, maybe, if you didn't buy it new, it's been there all along along and you were the unlucky recipient of the result?

  • Haha 1
  • 1 year later...
Jerome Veal New Member

Jerome Veal

Posted
Posted

Same Issue here but with left rear passenger door. Power step doesn't come down. no signal that door is open or closed. it the door will lock and unlock. I found thick black wire broken. Does anyone have a wiring diagram?

  • 1 month later...
PNW Donnie New Member

PNW Donnie

Posted
Posted (edited)

Im having the same issue in a 2015 2500. I replaced the whole door wiring harness and the door latch assembly on driver door and still having the same intermittent issue. Any ideas? im wondering if maybe its computer related?

Edited by PNW Donnie
To add more info
GMCustomerService Senior Enthusiast

GMCustomerService

Posted
Posted
On 2/3/2025 at 4:01 PM, PNW Donnie said:

Im having the same issue in a 2015 2500. I replaced the whole door wiring harness and the door latch assembly on driver door and still having the same intermittent issue. Any ideas? im wondering if maybe its computer related?

Our team regrets to hear of this concern with your vehicle and we would like to look into this further on our end. To get started, we ask that you send us an email to [email protected]. Make sure to include your Username and Forum name in the subject line with additional details. We look forward to your response. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      Towing In Loose Gravel

      By Chuck FB · Posted

      I agree, there is no one answer fits all as every rig is different, one may be pulling some little aluminum fishing boat while another is towing a monstrosity that weighs a lot and hopefully the owner if the rig has some prior experience to know what drive mode they should choose.    It also struck me and this is from watching a few of those boat ramp escapades videos in the past, Ford being one of the vehicles that has the auto front axle hubs and sure enough its found out that one hub has crapped out and won't engage and may not have manual hubs to even select on both sides so they are on the boat ramp stuck with no four wheel drive and spinning .... they flat out need a tow to get up the ramp and deal with the vehicles new found issues. That can happen to all brands of pickup, finding out either four wheel drive or 4 low isn't working right at the time its needed it to work as some electronic crap has failed. 
    • Chuck FB
      Towing In Loose Gravel

      By Chuck FB · Posted

      Its possible you never had the joy of the crappy boat launches we tend to have around here or really some of them are just grades down to the river if its a river scenario and the conditions change all the time with the river levels and silt deposits. Some of the lakes we went to years ago, there was no such thing as a cement pad that went down into the water that the trailer stayed on, it was gravel maybe up to the water line and then duck crap much beyond that so sinking the boat tires into mud. Of course some of the more established lakes had a cement bar type boat ramp but sometimes it was covered in green slime closer and certainly within the water and a two wheel drive had all sorts of fun if one had to touch that slime with the rear tires.    A neighbor of mine had made a comment years back with his chev truck that was probably about the same year as yours but a half ton extended cab 4x4 and he a a fiberglass boat with an inboard so it wasn't a feather weight and he had gone out to one of the large popular lakes in the area and don't ask me how this happened but he was in two wheel drive as he figured he didn't require four wheel drive for that boat ramp and somehow upon pulling the boat out he twisted one of his drive axles. I suspect it must have spun and then grabbed on the cement ramp and shocked it to the degree of twisting it. He would have had the standard 8.5 or whatever it was axle housing as the 9.5 ring gear like my truck has also has larger drive axles as far as I know. Anyway he was feeling a vibration driving home and had it checked out and a shop found that the tire/hub was wobbling because of the axle had twisted so in went a new drive axle. After that bad experience he said he made sure to put it into four wheel drive to lower the stress on the rear axle. Of course that is where an HD truck can handle a lot more stress and no doubt these newer half tons with their larger ring gears probably have larger drive axles as well to match vs back in the day. 
    • asilverblazer
      2027 GMC Sierra: Official Discussion

      By asilverblazer · Posted

      Desirable - as in does someone WANT one, aspire to have one. Could reasonably buy any car they want and CHOOSE these instead.    I didn't watch the video, why did they win?
    • Atlas
      Towing In Loose Gravel

      By Atlas · Posted

      The use of absolutes like "always" to describe gear selection, and giving free advice at a boat ramp sounds like a recipe for disaster. It's a boat ramp, not a farm, for starters.   IMO gear selection should depend on the obstacle. If low range is working and this is a slower speed, controlled ordeal, I'd keep using that.
    • diyer2
      Towing In Loose Gravel

      By diyer2 · Posted

      I had a boat for many years, never had a problem even with a 2 wheel drive 93 Silvy for 20 years. Good tires, proper use of the gas pedal worked.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...