Jump to content

Recommended Posts

Posted
52 minutes ago, Roadrunner45 said:

To update on the disposition of the repairs.  The good news is the thumping seems to be less pronounced than before but still present. In park and drive at slow speeds it seems a tad bit less than previously. I used to hear the sound through around 4-5 gear that seems to have been corrected at least in the short drive from the dealer to my home. Going to put it to the test tomorrow and tow my 14,,500 pound 5th wheel almost 700 miles. 

I will update of any changes from my first impressions.

I was really hoping this was the fix my service department said that a few with this issue had been corrected by the pump replacement but not in this case. The tech would did the work stated the the bottom end of the engine looked great no shavings in the oil, blue-ing of the rod caps etc.

 

Thanks for the update!  Good to know they did not find any major damage but I was sure hoping the knock would be gone.  

Ours is still as loud as ever but does not seem to be causing any other issues.   Put over 1200 miles on it last weekend with no issues.  

Love the 10sp tranny and the gas mileage we get.  Going to hope it gives us years of worry-free driving!

Posted

I have the same what I call "clunking" noise in my 3500HD Denali that got a little louder after putting 500 miles on it.  It is for sure noticeable when standing outside the truck.  The good news is that it's very faint in the cab and as it warms up it pretty much goes away inside the cab.  Especially with the radio going.  So if you no longer hear the noise in the cab, especially after warming up, I would say this is something everyone else has versus being an excessive noise.

Posted
19 hours ago, Roadrunner45 said:

To update on the disposition of the repairs.  The good news is the thumping seems to be less pronounced than before but still present. In park and drive at slow speeds it seems a tad bit less than previously. I used to hear the sound through around 4-5 gear that seems to have been corrected at least in the short drive from the dealer to my home. Going to put it to the test tomorrow and tow my 14,,500 pound 5th wheel almost 700 miles. 

I will update of any changes from my first impressions.

I was really hoping this was the fix my service department said that a few with this issue had been corrected by the pump replacement but not in this case. The tech would did the work stated the the bottom end of the engine looked great no shavings in the oil, blue-ing of the rod caps etc.

 

You say a bit less so does that mean not very noticeable? Do they have any idea what may be causing the thumping noise? I've heard it may be the motor echoing through the bell housing. That explanation seems odd because I've heard others with up to 10K miles with a very faint noise that you have to listen for. Mine can be heard with the radio on at times. And at times not loud at all. It does get louder when it's warmed up though. 

Posted (edited)

Ok update I now have 3500 miles on my truck I am the original poster of this thread. My truck is warm and in the garage idling while I add some DEF and I think the knocking has gotten better. I have not changed the oil or anything. Just driving it.
So I took another video while in the garage to compare with the original.


Here’s the original

 

 

 

 

 


I don’t think I’m going to worry about it and I’ll see how it sounds after my first oil change


Sent from my iPhone using Tapatalk

 

Edited by bass mechanic
  • 2 weeks later...
Posted

I just picked up my 2020 denali 2500 hd duramax today.

This is my third duramax and my 5th diesel.

I'm 70 yrs.old and been a tech and shop owner most of my life.

Noticed the thump/knock immediately. 

Went to the salesman and listened to another denali diesel.(new)

It was quiet as a baby. Then went to the service advisor and the diesel tech with the same old BS that it was normal and they really couldn't hear what I heard. They said to drive it, and don't worry, it's under warranty.

I think someone should post an email address and phone number we can all flood with our same problem.

There's safety in numbers and Hopefully,,if they get enough owners complaining, they might get off their butts and do some actual research on the problem.

I know GM has changed the lift pumps recently because the Bosch pumps were manufactured for diesel fuel sold in Germany.  The problem was that US diesel was thinner which contributed to lift pumps overheating and creating metal shavings that damaged the engines. Maybe these new pumps might be a good place to start.

Any updates from the forum are greatly appreciated,  and I  will update as time goes by.

Thanks to all who have taken the time to post so far. 

Posted

I agree that we should all complain to GM.    Bought 2020 Chevy 2500 High Country in November.  Noticed the thump/knock right away.  Same response from my dealer... it is normal.  

Posted
8 hours ago, Colossus said:

well what if it is normal? 

If it is, why do some 2020 Duramax's have and some do not?  Some are much quieter as well but still have it.  Why are there so many different answers from dealers across the country saying all kinds of things?   We are hoping it is normal too and our new truck lasts for years but it is a nail biter for sure when you spend that kind of money!

Posted

For what it's worth, and as I mentioned in another post, it definitely sounds like a pump of some sort to me.  I notice that the knock comes on for 1-2 seconds right at cold start-up, then the overall sound of the motor changes (hard to describe, but like a higher idle and maybe a change to injection timing versus compression due to the cold start). Then the knock stops for 2 minutes or so.

 

Also, it seems to be knocking at less than engine speed (could rule out an issue with rotating assembly).

 

If it is not the fuel/lift pump, could it be something with the turbo?  I am not familiar with how it works. Could it be some sort of waste gate "puffing" or something?

Posted
1 minute ago, Tomato said:

For what it's worth, and as I mentioned in another post, it definitely sounds like a pump of some sort to me.  I notice that the knock comes on for 1-2 seconds right at cold start-up, then the overall sound of the motor changes (hard to describe, but like a higher idle and maybe a change to injection timing versus compression due to the cold start). Then the knock stops for 2 minutes or so.

 

Also, it seems to be knocking at less than engine speed (could rule out an issue with rotating assembly).

 

If it is not the fuel/lift pump, could it be something with the turbo?  I am not familiar with how it works. Could it be some sort of waste gate "puffing" or something?

the issue with this is 1 undeniable fact, the sound is a deep thud sounds unmistakably either inside the block or if your theory is correct something attached to the block. sounds exactly like rod knock 

Posted
5 minutes ago, bass mechanic said:

the issue with this is 1 undeniable fact, the sound is a deep thud sounds unmistakably either inside the block or if your theory is correct something attached to the block. sounds exactly like rod knock 

You don't think it is at too slow of an RPM to be a rod knock?  Too bad we can't connect a timing light to compare.  Or is there a way to connect some sort of tool to each cylinder that tells you when it reaches TDC?

Posted

I spent a few minutes with my listening device (stethoscope) and found that the thumping was most pronounced and resonated where I am pointing with the orange handle in the 2 pictures. I do not know diesels well at all, but I believe this is all part of the turbo, right?  Good to note that I did not pick anything up at the bottom of the motor or on the tops of the valve covers. Thoughts?

FDBE0E92-A56B-4041-9AE7-9532CFB284AB.jpeg

Posted

This is the second area where the sound is most pronounced.  It is the back tube coming off the top of the motor.

54EDA00B-4DC0-4EF7-AEB0-57AA90C80871.jpeg

Posted
1 minute ago, Tomato said:

This is the second area where the sound is most pronounced.  It is the back tube coming off the top of the motor.

54EDA00B-4DC0-4EF7-AEB0-57AA90C80871.jpeg

well if that's true my assessment is if the sound comes from that far up on the engine it is a fuel injector and is likely normal.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.6k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,993
    Total Members
    8,960
    Most Online
    President Roberto
    Newest Member
    President Roberto
    Joined
  • Who's Online   1 Member, 0 Anonymous, 207 Guests (See full list)


  • Latest Articles

  • Posts

    • I don't wanna do major surgery/upgrades, behind-the-dash work, add amps, change radio etc. on my '26 std cab WT. On the WT, it has the base 7" IOR infotainment setup, and only two speakers (doors). Since I listen to classical, looked around for speakers that do well and dug thru reviews. Two-way speakers were found to be better than 3-way. So I've ordered a pair of  Infinity Reference REF-9632IX 2 way speakers.  [These may  or may not have been discontinued / succeeded by the 3-way ...9633 ones.]    These speakers are lauded for 3 ohm and 94db sensitivity spec so they'll work well for ordinary base car radios without amps and offer better performance (quality,  strength) than  default base paper-cone speakers. They'll be installed in a few days and I'll let y'all know what I think. Bill W San Jose      
    • Thanks!   Changed out the rear shocks today to Bilstein 5100s.  So far feel much better. The stock Rancho were wore out.  Lots of heavy hauling (2 moves, home renovations, etc).  Next up is new BFG tires Monday.  Cant wait the current tires have little to no wet traction and are super loud (hum)    
    • Ok, I got the all the codes. What do you all think would be a place to start?
    • How about I just point to the factory pans stand pipe little drain plug and claim its a pan with a real drain plug !. I just couldn't swallow the fact that a Dorman pan which at this point is probably the only pan out there that fits the gas version truck cost that much up here in Canada so I decided initially anyway to skip it and see what I thought of pulling the pan method and down the road if I felt inclined enough then I would either install a drain plug kit in the factory pan if there is enough room for it, or have a bung welded onto it, or put an aftermarket pan on. The thing is if the pan is not pulled then the magnets in the pan can't be inspected and cleaned or if wanting to change out the filter. However of course it certainly would make the job easier to be able to drop the oil first before having to handle the pan if dropping the pan that go around was the goal.    I knew a guy locally that was doing custom field spraying years ago with a pickup pulling a ground driven sprayer, I believe it was a GM pickup with an automatic trans. He had a drain plug in his pan and would drop the oil out of it once a week and top it back up through the dipstick tube to keep refreshing a portion of the oil often and that made the transmission last far longer than had he done nothing. Soft fields pulling 500 gallons of water at the start of each mixed up sprayer tank batch and in low range sucking along. I imagine he got some tips from other custom sprayer outfits doing the same thing at the time and learning from their blown up tranny mistakes. Transmissions then had no lock up converter so would cook the crap out of the fluid slipping that much and it would not have been synthetic fluid either. 
    • 3.39 Kroger’s in Montgomery Texas. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...