Jump to content

Noisy steering column

STGS

By STGS
in Troubleshooting, Warranty & Recalls

 Share

Recommended Posts

Shawn H Enthusiast

Shawn H

Posted
Posted

I took matters into my own hands today and took it apart myself and made a video. I added grease to the intermediate shaft to fill in the slop on the 2 pieces now my steering is smooth like it supposed to be I know this wont last forever but its gotta last more than 2000 miles or until GM comes up with a fix. 

 

  • Replies 108
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

MTU Alum
MTU Alum

The rattle you are likely hearing is hydraulic.  It occurs at low speeds around 5 to 15 mph when hitting chatter bumps or larger bumps in parking lots.  I often get it driving into driveway when going

Warren underhill
Warren underhill

I have the same steering clunk at low speed turns as well on my 2020 Denali HD with digital steering. I hoped in a new ltz Silverado and the same thing...... I haven’t herd that noise since my 2006. T

STGS
STGS

It's definitely inside the cabin.  I would say it's the bearing or bushing in the column. It coincides with the turning of the steering wheel at slow speeds.

EastCoast HD Enthusiast

EastCoast HD

Posted
Posted
18 hours ago, Shawn H said:

I took matters into my own hands today and took it apart myself and made a video. I added grease to the intermediate shaft to fill in the slop on the 2 pieces now my steering is smooth like it supposed to be I know this wont last forever but its gotta last more than 2000 miles or until GM comes up with a fix. 

 

GM must have had a pile of GMT800 ISS’s sitting around and decided to use them up. Can’t believe this issue is reoccurring! WTF!

 

Thanks for confirming and sharing your video. BTW, you didn’t mention this or show it in the video, but you need to be careful when removing the shaft so that the steering wheel does not spin freely. It could damage the airbag clock spring. I also noted this in the video comments.

TboneTX New Member

TboneTX

Posted
Posted

Hey Everyone, was just searching around for this same problem and came upon this thread. I have a brand new 2020 Chevy 2500 Gas (had 80 miles on it when i got it). Steering didn't really fee correct from the beginning. I have had a 2016 Denali 1500, 2018 SLT 1500 and never experienced this before. So I took it in for steering wheel shake and what seemed to be an alignment issue on Nov 19th . They did the alignment, but it didn't really help all that much- seemed better but not much. When driving down the highway at 65 plus, the steering feels loose and sometime cocks the wheel left or right 1-2 degrees. I also notice the clunking when at low speeds when pulling out of my driveway and it only happens in the morning when its cold and at less that 15 mph. When doing a search I ran across this bulletin as well. So wondering if its related or not.  Its an official service bulletin from GM so i would suspect they are starting to investigate it. Hopefully they do something fast. Im not into buying expensive trucks that should work properly right out of the gate. At the price point, the damn thing should be just about flawless. 

 

 

Steering Dither/Shake or Quick Steering Wheel Oscillation at Speeds of 80-129 km/h (50-80 mph)

 20-NA-192 1..2 (nhtsa.gov)

 

 

 

Wes 2020 New Member

Wes 2020

Posted
Posted

Bought a 2020 3500 HD GM Denali. The truck is used in a forestry buisness so lots of rough road driving. The steering literally sound like a loose bucket of bolts at slow speeds.  They first changed the column shaft with no luck and finally the whole steering column itself. Never changed a thing. Driving me crazy.  Would not know there is a problem if I stayed on the pavement. Seriously considering dumping it on a Ford.

kylant Enthusiast

kylant

Posted
Posted
On 12/7/2020 at 5:03 PM, Shawn H said:

I took matters into my own hands today and took it apart myself and made a video. I added grease to the intermediate shaft to fill in the slop on the 2 pieces now my steering is smooth like it supposed to be I know this wont last forever but its gotta last more than 2000 miles or until GM comes up with a fix. 

 

thanks for posting that video.

the clicking I have is definitely coming from those little white bushings/collars in the firewall boot. I have to take that apart and grease those.

 

I think my ISS is starting to clunk as well

paticus Enthusiast

paticus

Posted
Posted

Great video, that's exactly the slack I am experiencing. I am surprised that GM F'd up such simple/common component.

 

I wonder if we can get lucky with a good shaft replacement, or if all replacements are faulty. It would be kind of unbelievable to think all HD's are experiencing this issue after 5k miles or so.

mcloop New Member

mcloop

Posted
Posted (edited)

I have a 2020 AT4HD with this exact problem. I've taken it to the dealer and they've blown me off saying they don't see a problem and everything is "normal". I can make the noise and feel the knock with the steering wheel and I feel and hear it driving the 1/2 mile of dirt road to my house (5 to 10mph). It drives me nuts since I'm $90k into this truck. How do we get GM involved if the dealer is ignorant?

 

**Update** Just contacted GM and escalated. Will update after that conversation.

Edited by mcloop
BushChevy2020 New Member

BushChevy2020

Posted
Posted
On 11/3/2019 at 6:17 PM, STGS said:

Have a 2020 Chevrolet 3500 4wd.  Anybody else have the noisy steering column. Has a popping click sound when making slow speed turns.  Never hear it at highway speeds.  Always at slow speed maneuvers.  My 15 did it also but my 17 did not.  The one thing that my 15 and my 20 have in common is neither had the digital steering assist.  My 17 had the assist and didn't make the noise. Drives me crazy.

I have a 2020 Chev 2500hd with same issue. at 5000km they replaced steering shaft. Now at 6400km its back. 

Sometimes at crawling speed i get a sound like a gear issue with the steering.

Ckhris Enthusiast

Ckhris

Posted
Posted

Unbelievable GM still has steering shaft issues. My 94 1500 silverado had intermediate steering shaft issues when I owned it and 26 years later and they still do. 

Ckhris Enthusiast

Ckhris

Posted
Posted
On 12/10/2020 at 3:19 PM, paticus said:

Great video, that's exactly the slack I am experiencing. I am surprised that GM F'd up such simple/common component.

 

I wonder if we can get lucky with a good shaft replacement, or if all replacements are faulty. It would be kind of unbelievable to think all HD's are experiencing this issue after 5k miles or so.

I guarantee you a lot of people are experiencing it. Until they come out with a redesigned part it will continue to have issues 

Dnuts New Member

Dnuts

Posted
Posted (edited)
21 hours ago, Ckhris said:

I guarantee you a lot of people are experiencing it. Until they come out with a redesigned part it will continue to have issues 

 

On 12/7/2020 at 6:03 PM, Shawn H said:

I took matters into my own hands today and took it apart myself and made a video. I added grease to the intermediate shaft to fill in the slop on the 2 pieces now my steering is smooth like it supposed to be I know this wont last forever but its gotta last more than 2000 miles or until GM comes up with a fix. 

 

I’ve had my intermediate shaft replaced twice now as well. I saved myself a trip to the dealer today and took out the shaft and greased the hell out of it. I also put an  o ring over the gap on the shaft to keep the grease in. The noise and clunking has gone away for the time being. I’m going to wait for the upgraded part to come out. 

Edited by Dnuts
Ckhris Enthusiast

Ckhris

Posted
Posted
13 minutes ago, Dnuts said:

 

I’ve had my intermediate shaft replaced twice now as well. I saved myself a trip to the dealer today and took out the shaft and greased the hell out of it. I also put an  o ring over the gap on the shaft to keep the grease in. The noise and clunking has gone away for the time being. I’m going to wait for the upgraded part to come out. 

Grease is temporary, the grease the dealers uses is tacky. 
i went as far as drilling and tapping a hole and installing a grease zerk

kylant Enthusiast

kylant

Posted
Posted

i looked to see if Borgeson has a shaft available. Their shaft goes up to '19. 

I looked at part numbers for the 2020 shaft and it looks like it is compatible with trucks back to '17??

 

I called Borgeson, and the guy who I talked to (less than helpful) said the shaft only goes up to '19. He didn't offer any reason as to why or if it would work on the 2020.

I think he was just reading what was on the computer in front of him. I got the impression he didn't have any idea ??‍♂️

  • 2 weeks later...
Stand By Enthusiast

Stand By

Posted
Posted

Just a thought. You could order the early shaft from an auto parts store. Most would let you order it to look at and compare before buying it. Some may even be able to get the borgeson in and compare. If it doesn't match, they'll just ship it back to the warehouse.

  • 1 month later...
mcloop New Member

mcloop

Posted
Posted
On 12/16/2020 at 12:20 PM, kylant said:

i looked to see if Borgeson has a shaft available. Their shaft goes up to '19. 

I looked at part numbers for the 2020 shaft and it looks like it is compatible with trucks back to '17??

 

I called Borgeson, and the guy who I talked to (less than helpful) said the shaft only goes up to '19. He didn't offer any reason as to why or if it would work on the 2020.

I think he was just reading what was on the computer in front of him. I got the impression he didn't have any idea ??‍♂️

Has anyone had experience with the Borgeson shafts? Are they much more superior to the stock GM shafts?

I checked the GM part numbers 2019 compared to 2020. They are the same, so I could try the Borgeson.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,938
    Total Members
    8,960
    Most Online
    C. Hart
    Newest Member
    C. Hart
    Joined

  • Who's Online   4 Members, 1 Anonymous, 629 Guests (See full list)

  • Latest Articles

  • Posts

    • jgaudet99
      Tire psi

      By jgaudet99 · Posted

      Thanks everyone for the help!   I'm going to stop into the scales one of these days and weigh my axels, for the time being, I am going to run Toyo's recommendations and also do a chalk test. I have a tire shop that's going to try their scanner to reprogram and set the the factory psi values lower, and if they can't I'm going to order a scanner and do it myself!
    • KARNUT
      Exhaust Question

      By KARNUT · Posted

      You won’t do better than stock exhaust without headers. Just put your favorite muffler on it and it will do the job. 
    • C. Hart
      Exhaust Question

      By C. Hart · Posted

      I have seen different people in different places post different sizes of exhaust as stock for my 2014 Sierra L83. Some say 2.5 some say 2.75. I am considering replacing the muffler with a Dynomax Super Turbo, perhaps 17739.  I had the factory L83 5.3 replaced with another L83 5.3 from Jasper Engines. I also put new Walker Cat / Y pipe on. I would appreciate opinions suggestions about what would be a good muffler setup. My main interest is a low rumble and the best flow / fuel mileage I can get. Not interested in straight through glass packs or loud exhaust. Those days are way behind me now.  Thanks Guys.  
    • newdude
      Cold start Miss, oil in cylinder

      By newdude · Posted

      Its coolant disguised as oil.   TSB 20-NA-166 -  20-NA-166 1..3   "To inspect for this concern, add coolant dye to the system, run the engine through warm up, pressurize the cooling system after warming the engine to operating temperature (let the engine cool overnight) and inspect the suspect cylinder with a borescope for coolant dye evidence. At times it may be necessary to remove the head for inspection. If the head casting line is the concern, the intake port will be wet with a coolant oil mix"     I'd say its the head, and its either leaking at the casting line and dripping down the intake into the cylinder, or its another spot on the casting itself at the cylinder that is getting wet.  
    • asilverblazer
      Cold start Miss, oil in cylinder

      By asilverblazer · Posted

      Can you sample the pooled liquid, enough to confirm it is oil?   ...That its not fuel or coolant.   Also, make sure combustion gases aren't entering the cooling system.   Simply put, either oil being pushed up past the rings (this really isn't possible), oil leaking past the head gasket, oil leaking past the valve, oil entering through the intake air path. If none of this is likely - it may not be oil.   What could be likely is the fuel injector leaking down. A puddle of gas would still smoke and rough idle. (Same cylinder has the same problem after injector replacement?)   What is the crank time first thing in the morning, when the puddle would be present? Does it seem like the high pressure fuel pump needs an extra second or two to rebuild the pressure that injector 8 may have let bleed off? Check the fuel pressure via a scanner prior to starting the engine.    

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...