Jump to content

Keep accessory power on indefinitely w push button start?

Ezekiel2517
 Share

Recommended Posts

Ezekiel2517 Enthusiast

Ezekiel2517

Posted
Posted

When camping, I would like to keep my accessory power on to keep the wireless hotspot running.  If I had a key this would be a non issue. However the push button start turns off power after about 20 minutes.  Anyone know of a way to make it run longer?  

 

I plan to keep it plugged into the AC powered trailer.  The trailers DC converter which should keep the battery charged.  

vulcan_classic Enthusiast

vulcan_classic

Posted
Posted (edited)
16 hours ago, Ezekiel2517 said:

When camping, I would like to keep my accessory power on to keep the wireless hotspot running.  If I had a key this would be a non issue. However the push button start turns off power after about 20 minutes.  Anyone know of a way to make it run longer?  

 

I plan to keep it plugged into the AC powered trailer.  The trailers DC converter which should keep the battery charged.  

if you hold the start button about 10 seconds it will turn everything on like turning a key on without starting the engine. Not sure how long it will remain on though, worth a try. Of course you'll need to leave FOB in the vehicle.

Edited by vulcan_classic
Codeman00 Enthusiast

Codeman00

Posted
Posted

Just to confirm, if you press the start button for 10 seconds, the auxiliary plug in the tailgate is active with power for the long term? 

Ezekiel2517 Enthusiast

Ezekiel2517

Posted
  • Author
Posted (edited)

The accessory power keeps the truck electrical turned on.  Usually this would drain the battery.  The RV system has a dc converter that keeps the 12v system charged.  Its wierd but even AC systems are run by DC controls.  It will backfeed the connected vehicle.   I ran the wifi for about 3 hours like this and had no issues.  I'll try longer next time. 

Edited by Ezekiel2517
Maven Enthusiast

Maven

Posted
Posted

Yup, if your trailer has a battery maintainer that keeps stable voltage on the same circuits that truck feeds with trailer pin E, then your trailer will keep your truck battery maintained.just be sure you don't have an isolation switch on the trailer that doesn't allow it to power that circuit to the truck. 

Ezekiel2517 Enthusiast

Ezekiel2517

Posted
  • Author
Posted

How would I determine if it has an isolation switch?  I ran if for about 4 hours with no issues this way, but Im not sure if 4 hours would have drained the battery in the truck anyway.

 

 

Ezekiel2517 Enthusiast

Ezekiel2517

Posted
  • Author
Posted

This will be great if we get to go to Garner State Park this year.  ATT is the only service that works out there.  We have verizon an T-mobile so this will allow us to connect to an ATT hotspot

snork Enthusiast

snork

Posted
Posted
On 3/14/2020 at 2:26 PM, vulcan_classic said:

if you hold the start button about 10 seconds it will turn everything on like turning a key on without starting the engine. Not sure how long it will remain on though, worth a try. Of course you'll need to leave FOB in the vehicle.

how dare you call my girlfriend a FOB, and why does she need to stay in the vehicle ??

  • Haha 2
dawg99 Enthusiast

dawg99

Posted
Posted

From GM Upfitters. Hope this helps.

 

Description and Operation Power Outlets Description and Operation 12 Volt Power Outlet Receptacle Description and Operation

The vehicle is fitted with a 12 Vaccessory power receptacle. The accessory power receptacles are controlled by an ignition operated relay. The accessory power receptacles are operational when the ignition is turned to either the On or the Accessories positions. The X80J and X80K accessory power receptacles may be configured to be operational when the ignition is Off by changing the position of the 50A fuse from the F10DL position to the F11DL position in the passenger side panel fuse block. 

 

I just changed my cigarette lighter plug from always hot, to accessory hot in my 20 sierra by moving the fuse.

  • Like 1
Ezekiel2517 Enthusiast

Ezekiel2517

Posted
  • Author
Posted
On 4/1/2020 at 11:02 AM, Jav_eee said:

Don’t people go camping to “get away” from things like Wi-Fi and other technology?


Sent from my iPhone using Tapatalk Pro

Yes, but sometimes when you cant get completely away from work you need ability to check in and function.  Otherwise you have to cut your trip short and leave.   Thats what modern society demands.

  • 7 months later...
Dave's Place Enthusiast

Dave's Place

Posted
Posted (edited)

Press and hold the start button for more than 5 seconds and it will go into diagnostics mode,  You can get out and lock the doors and it won't shut off - I tested for 25 minutes.  Someone said a 6 Amp maintainer did not stop the battery from dying if left on a long time.  Another said a 15 amp charger kept it up.  Anyone know how many amps the truck pulls in Diagnostic mode?  I'd like to use a minimum amp charger.   Will a charger cause any other problems with the key on?  BE SURE TO TURN THE LIGHTS OFF from auto.  Press start again to shut it off.

Edited by Dave's Place
  • 4 months later...
Bluefella Enthusiast

Bluefella

Posted
Posted
On 3/14/2020 at 12:26 PM, vulcan_classic said:

if you hold the start button about 10 seconds it will turn everything on like turning a key on without starting the engine. Not sure how long it will remain on though, worth a try. Of course you'll need to leave FOB in the vehicle.

I don’t leave a fob in the vehicle. Expect the batteries to run dead flat over night. Even with NOCO battery “maintainers” they let the batteries drop below 12.3 volts. Over time batteries will need replacing prematurely. 
Im still looking for a suitable maintainer in excess of 10 amps. Any advice welcome 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,938
    Total Members
    8,960
    Most Online
    C. Hart
    Newest Member
    C. Hart
    Joined

  • Who's Online   2 Members, 1 Anonymous, 622 Guests (See full list)

  • Latest Articles

  • Posts

    • jgaudet99
      Tire psi

      By jgaudet99 · Posted

      Thanks everyone for the help!   I'm going to stop into the scales one of these days and weigh my axels, for the time being, I am going to run Toyo's recommendations and also do a chalk test. I have a tire shop that's going to try their scanner to reprogram and set the the factory psi values lower, and if they can't I'm going to order a scanner and do it myself!
    • KARNUT
      Exhaust Question

      By KARNUT · Posted

      You won’t do better than stock exhaust without headers. Just put your favorite muffler on it and it will do the job. 
    • C. Hart
      Exhaust Question

      By C. Hart · Posted

      I have seen different people in different places post different sizes of exhaust as stock for my 2014 Sierra L83. Some say 2.5 some say 2.75. I am considering replacing the muffler with a Dynomax Super Turbo, perhaps 17739.  I had the factory L83 5.3 replaced with another L83 5.3 from Jasper Engines. I also put new Walker Cat / Y pipe on. I would appreciate opinions suggestions about what would be a good muffler setup. My main interest is a low rumble and the best flow / fuel mileage I can get. Not interested in straight through glass packs or loud exhaust. Those days are way behind me now.  Thanks Guys.  
    • newdude
      Cold start Miss, oil in cylinder

      By newdude · Posted

      Its coolant disguised as oil.   TSB 20-NA-166 -  20-NA-166 1..3   "To inspect for this concern, add coolant dye to the system, run the engine through warm up, pressurize the cooling system after warming the engine to operating temperature (let the engine cool overnight) and inspect the suspect cylinder with a borescope for coolant dye evidence. At times it may be necessary to remove the head for inspection. If the head casting line is the concern, the intake port will be wet with a coolant oil mix"     I'd say its the head, and its either leaking at the casting line and dripping down the intake into the cylinder, or its another spot on the casting itself at the cylinder that is getting wet.  
    • asilverblazer
      Cold start Miss, oil in cylinder

      By asilverblazer · Posted

      Can you sample the pooled liquid, enough to confirm it is oil?   ...That its not fuel or coolant.   Also, make sure combustion gases aren't entering the cooling system.   Simply put, either oil being pushed up past the rings (this really isn't possible), oil leaking past the head gasket, oil leaking past the valve, oil entering through the intake air path. If none of this is likely - it may not be oil.   What could be likely is the fuel injector leaking down. A puddle of gas would still smoke and rough idle. (Same cylinder has the same problem after injector replacement?)   What is the crank time first thing in the morning, when the puddle would be present? Does it seem like the high pressure fuel pump needs an extra second or two to rebuild the pressure that injector 8 may have let bleed off? Check the fuel pressure via a scanner prior to starting the engine.    

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...