Jump to content

Tailgate button/rear view camera plastic housing falls out

romeactual
 Share

Recommended Posts

romeactual Enthusiast

romeactual

Posted
Posted

Has anyone had this issue?

 

I‘m thinking I have to use some double sided tape to keep this plastic insert to stay from popping out.

Its pretty annoying as I can push it in and it will stay, but after driving the top portion of it pops out.
No damage to the plastic or surrounding area, really not sure why this happened. 

See picture. 

7DF5D6E0-CD82-4355-B8B2-45B6F7D473BB.jpeg

Tyler Jang New Member

Tyler Jang

Posted
Posted
As far as I know, it is fixed with nuts and bolts on both sides.
If the nut has came off the plastic mold, It can be happened.
Can you take a photo more inside detail?
Sjordan Enthusiast

Sjordan

Posted
Posted
On 8/11/2020 at 9:07 PM, Tyler Jang said:
As far as I know, it is fixed with nuts and bolts on both sides.
If the nut has came off the plastic mold, It can be happened.
Can you take a photo more inside detail?

There are no nuts and bolts on this assembly (at least not on a silverado).  I have over loaded my tailgate with lumber and when I emptied the bed and closed the tailgate it was popped out.  Mine popped right back in no issues since, I would go to the dealer before double sided tape.

scokill Enthusiast

scokill

Posted
Posted

I have the same thing.  It has popped out twice, and it doesn't fall open when using the Key FOB or button inside.  Of course the check it today and find no problem even when clearly didn't fall open when I showed it to the advisor...frustrating.

  • 4 years later...
  • 3 weeks later...
Mike Duhaime Enthusiast

Mike Duhaime

Posted
Posted

I had that happen soon after the dealer replaced the camera, and tailgate switch. They left the 2 10mm nuts loose!

then water got in, took out the cam again. They put in another cam, nut this time i remover the tailgate cover and added dielectric silicone to all plugs and switch, cam. Then added black RTV silicone to exterior of handle housing...to stop water from getting in.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • 520Zilla
      2021 suburban RST - acting up/lights flickering

      By 520Zilla · Posted

      Hi all,   I just bought a 2021 suburban RST with 88,000 miles on it and everything has been good but I’ve been noticing within the last month or so that there are small electrical things going on and I know what the AGM batteries and all the electric electrical in these big trucks you need to have a constant flow with good voltage   That being said, I bought a new battery thinking that that might have something to do with it but today I went to get in and start it and it said no key found when I had the key right in my pocket   It also proceeded to flash the lights inside and outside for over 30 minutes as I went to disconnect the battery as soon as I touch the negative terminal, I heard the relay reset and everything come back up. I got in the truck and started it no problem.   Anyone else have this happen to them? I’m starting to think it’s the KARR system that the dealer installed short circuit stuff.
    • ManyCamaroz
      “Service Emission System” & “175 miles until “65 MPH Max Speed”

      By ManyCamaroz · Posted

      I don't drive this truck on a regular basis since I have a new company truck with no out of pocket fuel or maintenance cost. Yesterday I got it out to run some errands and got the title message on my DCI. A quick Google search suggested to first clean the Map Sensor. I pulled it out and it was sooty so cleaned it up and reinstalled it. Issue not resolved. My OBDII is a couple years old so didn't see any codes. Today I took it to a friend at AutoZone to get him to check it with his reader. It had the following codes: P20C3 P02BB P221F Stating the most likely solution is to replace diesel emission fluid (DEF) tank assembly.   So, I guess a trip to the dealer is necessary. I read where there was a backorder on these tank assemblies several years ago so hope that has been resolved.
    • Chuck FB
      Do you keep your tires at full capacity? 80psi

      By Chuck FB · Posted

      Are you using a weight distribution hitch system with your trailer as that alone can change the actual tire pressure requirements needed. It would prove interesting to see what the actual individual axle weights are on your truck when you are hooked up to the trailer. In fact when your hooked to the trailer, typically if anything unless it has a large capacity weight distribution system that is over cranked, often the weight on the front axle will be less when hooked up vs driving empty and certainly if one doesn't have a weight distribution hitch. Really the only times one may get up there with weight on the steer axle is if there was a snow plow mounted on the front or a motorcycle on a rack or with a very large jockey tank full of fuel at the front of the box that transfers a bit of its weight to the front axle.    And of course your tires carry more weight for a given tire pressure due to their size vs a stock sized tire so there is that to take into the equation as well. 
    • Artemis
      New Member Just Bought a Vtrux

      By Artemis · Posted

      Great info here thank you. I just joined, we have a 2014 Silverado truck we bought about 4 years ago with less than 5,000 miles on it. It has approximately 24,000 on it now. It appears to have all the standard issues that people are talking about. Occasional charging problems especially using 110 volt, occasional blinking triangle where nothing will turn on when first starting the truck but it will reset itself if you wait 10 to 15 minutes. Noisy coupler between the flywheel and the generator. Our truck is speed limited to 74 mph, is there any way to change that? The latest issue we have been dealing with is when driving long distance on the highway at full speed the generator does not keep the batteries charged. The meter will go into the yellow/red border Zone for charge status and the yellow triangle will illuminate solid but the generator will not keep the battery charged, not sure why the controller doesn't tell the gas engine to increase RPM to increase generator output it usually stays well below 25 kilowatts even though the battery is discharging and I have to slow down the highway to 45 mph and eventually pull over and let the truck idle to charge the battery so I can continue driving at speed. Has anyone had this issue before or have any idea how to diagnosed it? When via Motors was around it they were very helpful at troubleshooting. This becomes much if the Terrain is hilly and you're towing a small trailer
    • Z45
      Tonneau cover that does not leak water

      By Z45 · Posted

      I have the GMC accessory (REV) cover installed by dealer. Ordered with the truck.  They did a very good install job, can't find a single issue. Some water gets in around the tailgate but no where else.  You can see daylight around the tailgate but that's not the covers fault.  Installation is means everything. Guys at my dealer were seasoned pros, not inexperienced here today good tomorrow types, like many dealers employ for these jobs.   I don't mind paying for a professional job.    

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...