Jump to content

Recommended Posts

Posted
2 hours ago, Wayne Black said:

It's also entirely possible that GM was having issues replacing faulty rear buttons and just decided they weren't needed and you could configure the front button to unlock all the doors.

 

When I was a Senior in High School my daily driver was a '57 Chevy and I know this sounds crazy, but you had to actually stick the key into the door and turn it 90 degrees to unlock your car!

 

Times were tough back then!

 

A friend had a '57 four door hardtop and to unlock the back door you had to reach around in the open front door and pull the button up!

By the end of the day, you were totally exhausted.

 

Sarcasm.

No way!  You're pulling our leg, right?

Posted
On 8/18/2020 at 2:34 PM, Wayne Black said:

It's also entirely possible that GM was having issues replacing faulty rear buttons and just decided they weren't needed and you could configure the front button to unlock all the doors.

If that were the case, they would have removed them from the Sierra too. They only removed them from Silverados. In other words, GM is saying: "You want door lock buttons on your rear doors? You can buy the more expensive truck."

  • Like 1
Posted
On 8/18/2020 at 2:34 PM, Wayne Black said:

It's also entirely possible that GM was having issues replacing faulty rear buttons and just decided they weren't needed and you could configure the front button to unlock all the doors.

 

 

If that were the case, they'd stop installing sliding rear windows and only provide solid glass ?

  • Like 1
  • Haha 1
  • 2 years later...
Posted (edited)

I know this is an older thread - I bought a 2023 Sierra 1500 Denali and was SHOCKED to realize that there isn't a button on the back doors.  My buddy who has a 2019 DOES have buttons on his.  I am curious if the wiring harness is there and I could swap out the door handles.  Anyone dug in to these trucks to find out? Thanks!

Edited by heffneil
Posted
On 8/13/2020 at 12:04 AM, AlaskaErik said:

GM doubles down on stupid so often now that eventually it's going affect sales.  My 2019 LTZ has buttons on all four doors and the rear buttons get used all the time.  That new F-150 with the 12 inch infotainment screen in the center stack is looking better and better.  If only it had something like the 6.2L.

 

The F150 doesn't have rear door handle lock/unlock either. Ford has eliminated a lot of features on the 2023's because of major chip shortages. The 2023 GMC interior I have blows away the 2021 F150 Platinum 4X4 Powerboost I owned. 

Posted

Well I had a Ford F150 Lightning and it was a lemon.  I bought the Denali and I liked the Ford interior 100x better.  The back seat was far larger, the seats are much wider, and the storage under the back seat was easily 2x larger.

 

To me, the ford interior was much nicer.  Also my phone was a my key and I had no problem locking and unlocking because I did have buttons on the back door handles.  Even the crappy explorer base model loaner I had, had the buttons on the back door handles.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,888
    Total Members
    8,960
    Most Online
    xdieselmechanic
    Newest Member
    xdieselmechanic
    Joined
  • Who's Online   1 Member, 0 Anonymous, 613 Guests (See full list)


  • Latest Articles

  • Posts

    • Holy s**t - not much of a parts thrower you say? You BLASTED that thing with the parts cannon!  You'd have been probably $1,000 ahead if you had just brought it to a competent shop rather than shotgunning a bunch of parts it clearly didn't need.   Just FYI - oil additives are really, REALLY good at ONE thing ... and that's emptying your wallet. They're ALL useless gimmicks.   If that has the L94 or L99, then #7 is an AFM cylinder. I'd suspect a failed lifter in that case.   If you leaned on wiring, sensors, and/or connectors while changing the oil, you'll have to check all that to be sure pins didn't get pulled out, connectors broken, etc.. Old wire loom that was barely adequate when new is certainly brittle by year 19 - make sure wires aren't chaffed and shorting out somewhere where you might have leaned. or supported yourself on it.   If your a mechanic, why didn't you just find out what you were missing and troubleshoot from there??  TIMED spark, fuel PSI / injector pulse, air, compression.  Can't make ANY money going the parts cannon route.
    • LOL! Are you joking?? That wax SUCKS! 100% gimmick made to "look" good.    After just TWO winters I had severe surface rusting in patches over 90% of the frame. Only reason it looks great in the pics is because I SATURATED the frame every single fall with used motor oil for 14 of the 16 years I owned it. Otherwise it would've been sent to the crusher 8 years earlier with the speed it was rusting prior!    I sold that POS 3 years ago. Was a gigantic headache the second it rolled off the showroom floor. Brakes pulsated on the TEST DRIVE. Door trim fell off the 1st week! Interior squeaked and rattled, and the drivetrain clunked after 2k miles. 4x4 switch failed shortly after. Front end - ball joints, struts, hub bearings - all failed between 38k-50k. Engine started burning oil at 50k. Rear and and transmission failed before 100k. Nothing but problems, and frustration with the piss-poor engineering designed to make you give up. Well, it worked! Nothing on that truck was easy to remove ... except the wheels. They haven't figured out how to screw that up yet. Give 'em time ...   I won't make that mistake again. EVER.   Such fond memories ... https://postimg.cc/K1qf23tS  https://postimg.cc/gallery/X02z64J  https://postimg.cc/gallery/mHSRXZv  https://postimg.cc/gallery/D4mMRfL
    • Different monitors do their test only under conditions specific to that monitor.  you MIGHT find the drive cycle conditions for the monitor that isn't ready on this site: https://lemon-manuals.la/   If it's not there, then it should be on alldata.com for your truck, but it requires a paid subscription.   And you need to know which specific monitor isn't ready.
    • from another thread   Update...although the truck sometimes seems to idle weird and the transmission shift a little weird, I've driven about 7,000  miles and no issues.   However, the way GM has handled my rental reimbursement, the situation when my truck quit, and the recall in general has led me to this point...I have driven a GM vehicle for the past 46 years and unless I buy a C3 Corvette, this is the last GM vehicle I will ever own. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...