Jump to content

Molle/MAPS Panel?

Derek Lewis
 Share

Recommended Posts

MidWestAT4 Enthusiast

MidWestAT4

Posted
Posted
On 10/31/2020 at 7:30 PM, Derek Lewis said:

Looking for a Molle/Maps Panel like the Valhalla panel for the Colorado. Anyone offer anything for the interior?

9E1AF661-D115-450A-83D2-B48D8B8D980E.jpeg

Me too!  

 

BuiltRight Industries has said they're working on GM products, but has been delayed for a while.  They do have some universal-fit panels that have some good looking mounting hardware, for the time being.  I too like the Valhalla panels for the Colorado.  Have you reached out to them regarding GM 1/2-ton options?  

  • 10 months later...
Transient Senior Enthusiast

Transient

Posted
Posted
On 9/22/2021 at 9:04 PM, Krazny13 said:

I have only found this one for the 2019-2021 Silverado so far.  

 

Seat Front Molle Panel

 

 

Looks like it might stick out a little too far.  I would love to see it installed.  I'd love to still a pistol there.  Shows potential. 

gemarsh Senior Enthusiast

gemarsh

Posted
Posted
11 hours ago, Transient said:

Looks like it might stick out a little too far.  I would love to see it installed.  I'd love to still a pistol there.  Shows potential. 

Lighting sucks due to gm's fantastic footwell lights.

20210123_163346.jpg

20210123_163121.jpg

Transient Senior Enthusiast

Transient

Posted
Posted
11 hours ago, gemarsh said:

Lighting sucks due to gm's fantastic footwell lights.

20210123_163346.jpg

20210123_163121.jpg

Thanks for providing the pics.  I was hoping for a side profile of the seats to see how far they stick out.  However, what you've shown me has me concerned about whether or not a gun would fit there anyways due to the molle panel being very close to the floor. 

BowtieBill Enthusiast

BowtieBill

Posted
Posted
12 hours ago, Transient said:

Thanks for providing the pics.  I was hoping for a side profile of the seats to see how far they stick out.  However, what you've shown me has me concerned about whether or not a gun would fit there anyways due to the molle panel being very close to the floor. 

They have a Universal Right Angle Bracket you can add to the center console side, may work for you.

 RIGHT ANGLE BRACKET (UNIVERSAL) – Desert Does It

 

  • Like 1
gemarsh Senior Enthusiast

gemarsh

Posted
Posted
On 9/26/2021 at 1:39 AM, Transient said:

Thanks for providing the pics.  I was hoping for a side profile of the seats to see how far they stick out.  However, what you've shown me has me concerned about whether or not a gun would fit there anyways due to the molle panel being very close to the floor. 

Thought you'd be interested in photos of the right angle bracket BowtieBill referenced. Maillady delivered yesterday and it works better than without.

 

First is the seat all the forward. Second is where I set, at 5'11. And then just others.

20211002_105656.jpg

20211002_105637.jpg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • asilverblazer
      Cold start Miss, oil in cylinder

      By asilverblazer · Posted

      Can you sample the pooled liquid, enough to confirm it is oil?   ...That its not fuel or coolant.   Also, make sure combustion gases aren't entering the cooling system.   Simply put, either oil being pushed up past the rings (this really isn't possible), oil leaking past the head gasket, oil leaking past the valve, oil entering through the intake air path. If none of this is likely - it may not be oil.   What could be likely is the fuel injector leaking down. A puddle of gas would still smoke and rough idle. (Same cylinder has the same problem after injector replacement?)   What is the crank time first thing in the morning, when the puddle would be present? Does it seem like the high pressure fuel pump needs an extra second or two to rebuild the pressure that injector 8 may have let bleed off? Check the fuel pressure via a scanner prior to starting the engine.    
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      Good information!  I didn't know about the dementia aspect and asked for a general for my second knee. I'd heard that recovery room time is usually shorter with a general.   The anesthesiologist talked me out of it and I had the spinal.  Inconvenience and/or discomfort is a small price to pay for reduced risk!
    • garagerog
      Navigating senior years.

      By garagerog · Posted

      This is for those over 70 years of age contemplating joint replacement surgery involving general anesthesia. Even some 55 yrs. ago when I took my pharmacology class the dangers of developing dementia in the elderly that had general anesthesia were beginning to be recognized. Over the years there has been some refinement in the cautionary warnings, avoid general anesthesia if possible if you've had close to 10 priors, especially over the age of 70 and/or a family history of dementia. I'm not including the twilight anesthesia induced by propofol often used in cytoscopies or colonscopies. Seriously think about seeing a neurologist and undergo cognitive testing before proceeding if any of those criteria apply to you. Spinal anesthesia may be an option in some cases. I'm in the above camp and although I could use a new right knee, I get fidgety according to a prior orthopedic surgeon when the bone saw spools up or maybe it was the smell of saw blade meeting bone, anyhow I may have one general anesthesia left in me which I will pocket for now and I'm choosing mind over mobility, anyway where did I leave my damn cane!
    • GMCustomerService
      July 2026 upgrade push issues

      By GMCustomerService · Posted

      We understand your frustrations with your auto start/stop, fuel gauge and cruise control concerns since your latest update, @LarT-26. You mentioned getting repairs completed, however, have your concerns been resolved? If not, we would like to learn more so we may explore the best path of assistance moving forward alongside your local dealership. When you have a moment, please visit: https://s.gmc.com/support-request and complete the request form with all pertinent details. This will help us to better understand your concern and ensure that it is routed correctly. We will keep an eye out for your outreach.
    • GMCustomerService
      Multigate electrical problem

      By GMCustomerService · Posted

      We understand your frustrations with being unable to open your Sierra’s top inner tailgate, @smitty81503. Your concerns are frustrating, and we would like the opportunity to explore the best path of assistance to pursue their resolutions. There are many different factors that could be the root cause of vehicle concerns, and we handle each one on a case-by-case basis. When you have a moment, please visit: https://s.gmc.com/support-request and complete the request form with all pertinent details. This will help us to better understand your concern and ensure that it is routed correctly. We will keep an eye out for your outreach.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...