Jump to content

DRL

Osbaldo Lopez
 Share

Recommended Posts

Osbaldo Lopez New Member

Osbaldo Lopez

Posted
Posted

I recently bought some new headlights, and the original ones I had didn't come with daytime running lights. So now the new ones I put in, the daytime running lights wont turn on. Does anyone know how to fix that.

DominatorZ71 Enthusiast

DominatorZ71

Posted
Posted
16 minutes ago, Osbaldo Lopez said:

I recently bought some new headlights, and the original ones I had didn't come with daytime running lights. So now the new ones I put in, the daytime running lights wont turn on. Does anyone know how to fix that.

Sounds like they're disabled through the BCM. Will need a tech II scanner to turn them back on. Personal advise if you bought new headlights, I hope they aren't the ebay special. They tend to have very poor quality everything that doesn't last or perform. But to answer your question it sounds like the DRL was disabled.

  • Like 2
Ravenkeeper Senior Enthusiast

Ravenkeeper

Posted
Posted
22 hours ago, Osbaldo Lopez said:

I recently bought some new headlights, and the original ones I had didn't come with daytime running lights. So now the new ones I put in, the daytime running lights wont turn on. Does anyone know how to fix that.

Are you the first owner for this truck?  If not, did the previous owner take the return spring out of the headlight control knob?  I'm sure that you have been driving with the knob in "AUTO."  @DominatorZ71 has the best idea, but I'm sure that @pgamboa has a trick or two up his sleeve, too.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • chris21
      Brand new to this forum. Questions about re-gearing my 26’ HD

      By chris21 · Posted

      37's would probably fit with a 3" lift. GM only has two gear ratios for these trucks 3.73 for gas and 3.42 for diesel. And they can't be programmed for anything else at the moment. The rough country module just corrects the speedometer and odometer to adjust for tire size it's not a programming device.   You haven't said if your truck is gas or diesel, but for a gas truck the 10L1000 with 3.73 gears has a lower final drive ratio than the 6L90 it replaced would if it were swapped to 4.10s. GM used the same 3.73 gearing in 6 speed gas trucks. I don't think you'll have any issue running 37's with the 10 speed other than the reduction in mpg and towing/weight capacity which is as much of a function of the lift as the tire size.
    • GN2018
      Range AFM/DFM Disabler Flaw

      By GN2018 · Posted

      Actually, it probably was the brakes.  It's weird the way the messages came across, but I took it to the dealer thinking that something was wrong with the sensor and in fact, the rear brakes were shot.  What I don't understand is why the messages never said, your brake pads are low.  First I got the message I posted above, taking about new pads being detected.  Then I got a message saying that the system needed repaired.  It never said, change your brake pads.
    • No1UKnow
      Transmission Woes :-(

      By No1UKnow · Posted

    • ryan35205
      Lets Talk Z60 Suspension

      By ryan35205 · Posted

      Did the KYBs keep it the same height in the front? I was concerned that pre-assembled assembly would raise it up an inch to standard non-z60 height.. I guess which it would make the rake 1 inch instead of 2 inches.
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      Thank you for keeping the train on the tracks and for a thoughtful engagement. I enjoyed the reflection on a previous stance to refine and improve your position. I like that inquisitive flexibility about you Atlas.    No the process isn't sterile. Hundreds, perhaps thousands of miles of piping, vessels, pumps. Chevron, the people I worked for, were keenly aware that there is a market for what is known as their "ISOCLEAN" line of lubricants. These are lubricants that are the same as those sold bulk that are further processed by filtration to a level your particular application demands. They will filter and package and provide lab documentation as required. Do not kid yourself. Every gallon of oil that goes into a Chevron Turbine, reciprocating compressor, generator is prefiltered and tested before being charged. Lest wise it was when I was there in the plants I worked in.    There are requirements set by manufactures for the cleanliness of the oils used in their equipment. OTR such as CUMMINS has standards shared with customers on this. Commercial interest selling to Ma and Pa do, but don't share that information. Not even upon request but internally, they do exist.    The GM study sited, (Graph from Machinery Lubrication in previous post) only shows "relative" importance.  I find that fascinating. By constructing the graph like this they admit there are dozens of factors in engine life and via scientific method determined the effect of 'relative cleanliness' on engine life not in miles but in 'FACTORS'. This allows a certain amount of reverse engineering does it not?   They even provided some touchstones. Beta 75 as a reference point. Wonderful stuff!!   Smaller blenders CAN and some DO take the time and effort to do better than a refinery or large bulk blender, like Warren Oil, in improving the "in the can" cleanliness. No I don't have a list but testing could generate that information.    Again, but one of several levers we can pull to improve engine life. The simplest is keeping a clean work station while doing your own oil changes.     

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...