Jump to content

Rust On Wheel Well - Replace or Fix?

igotostem
 Share

Recommended Posts

igotostem New Member

igotostem

Posted
Posted

Hi everyone,

 

The other day someone dented and scratched my passenger bed and drove off. The driver's side has rust, not terrible yet, in the wheel well. I live in PA so we get road salt.

 

I definitely want to repair the dent, but then the rust would need to be addressed at some point. Not sure how long it takes for the rust to spread and get real bad.

 

Worth it to just replace the bed with a takeoff or fix the rust while it is contained and also fix the dent?

 

Thanks

newdude Senior Enthusiast

newdude

Posted
Posted

The question really is what its like behind the outer skin.  If the flanges are shot where the inner and outer of the box meet at the wheel well, you'd be looking at not only a new outer skin but the wheel well metal itself.  

 

 

Jworks Enthusiast

Jworks

Posted
Posted

If the rust is just in the wheel well and not too bad as you said here's a "maybe" option.  I'd do this only on an old truck I wanted to keep.  But it might work on newer trucks too.  Like I said....this is a "maybe" option, to keep from going way overboard with new this and that.  Get the wheel off so you can get into the well easily.  If the rust is not all the way through with a hole showing you could use an  electric sander or hand sanding block to get rid of that rust, and get it all.  Don't leave any to spread.  It might be that you end up going all the way through the metal to get it all....I don't know, since I can't see it.  If you do, bondo works wonders at filling up places like that, and its sandable.  I've used Bondo Wood Filler with very good results.  But, of course, they make the body filler they're known for. About $11 at Walmart.  If you end up using that I'd then get some of that I would spray the sanded area good with 3 coats of cold galvanizing.  Follow instructions.  Then I'd get some of that rubberized spray-on bed liner and spray the inside of the well to keep (hopefully) further rust away.  Its just an idea. 

richard wysong Senior Enthusiast

richard wysong

Posted
Posted

all the panels and repair parts are readily available aftermarket, it depends on your skill level how far you go. maybe get the parts and take it to body shop?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      Oil Consumption

      By Chuck FB · Posted

      Through the years it hasn't been my typical method as I tried to drop oil on an engine that was hot from having been worked, however that was not always practical and had to fire up a unit and let it warm up reasonably well and drop the oil when I had the time to do it but am referring to not only vehicles but a variety of farm equipment and highway tractors etc. However on a vehicle where one is crawling under it and the exhaust is nearby to ones body and if wanting to pull the plug without danger of being hit with boiling hot oil or attempting to remove a HOT oil filter, its sure safer and easier to not have everything smoking hot and can remove the filter right away when under the vehicle and let it all drain. Of course its not the end of the world if a bit of oil stays in the engine that might have eventually found its way out, I like to get out as much as possible but any oil changes that take place in shops would rarely be sitting around for very long at all before the plug is thrown back in and filter slapped on and oil poured in and sent out the door quick like. There would be very little time spent ( assuming they even did it ) in starting the engine with oil to fill the filter, then waiting to verify the level on the stick. A good reason to check ones oil level shortly after a shop changed the oil on a vehicle just to make sure its correct and to look under for any oil around the drain plug or filter. 
    • CPhelps
      4 Wheel Drive System

      By CPhelps · Posted

      Cool to see another Vermonter!
    • diyer2
      Winter Returned

      By diyer2 · Posted

      To many wildfires.
    • diyer2
      Oil Consumption

      By diyer2 · Posted

      I have changed oil and filter for years by starting a cold engine to warm oil up, let it run 5-10 minutes depending on temperature. Drain until it starts dripping, refill with quantity from owners manual or get it close.   
    • Chuck FB
      Fluid Change Questions

      By Chuck FB · Posted

      I changed the factory fill oil in the rear diff of my truck for the first time today and the miles is close to 9000 on the truck. There was a lot of fines on the magnet, a very thick layer but working it through my fingers it all felt like mush and as most know it appears like graphite, so no surprise chunks anyway. Certainly was time to do it from my thinking and could have been done sooner but the oil didn't look awful but sure wasn't new looking and never expected it to either. I did use some solvent to help me clean out the bottom area of the axle housing, just get any other stuff settled at the bottom washed and wiped out of the housing for the bit of effort it takes. I used Amsoil Severe Gear 75W90 in the easy packs to try out what they are like and I used up 4 packs and didn't spill much at all in the process but did take all four of the packs and go to the work bench and emptied them into a measuring container and there certainly was some in them that added up to something, then poured that into one of the easy packs and squirted in what I could get out of it. I would say the level is within 1/8th of an inch of being level with the threads at the fill plug so just the perfect amount. Once again, more than what GM says the fill volume is but computes with what others are adding to their rear diffs as well. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...