Jump to content

Tailgate gap cover question

Sierra in the Sand
 Share

Recommended Posts

Sierra in the Sand Enthusiast

Sierra in the Sand

Posted
Posted

Anybody used this tailgate gap cover 84184471? Looks like it would be good for gravel or mulch, but I want to put on a tailgate strip light, and I wonder if it will work with this strip.

Transient Senior Enthusiast

Transient

Posted
Posted

I did.  Puked it off a few months later.  It was scratching the paint on the bed side of the gap.  It also caused the bushing on the right side of the tailgate to crack and the tailgate would pop out on that side and prevent it from closing.  I ended up pulling it after a few months and replaced it with a weatherstripping I found on Retrax's website.

PhilB Enthusiast

PhilB

Posted
Posted

I have the tailgate gap cover and Putco light bar.  The tailgate gap cover does not interfere with the light bar.

PhilB Enthusiast

PhilB

Posted
Posted (edited)

My Putco Blade light bar works as intended.  I have not looked to see if the tailgate gap cover has scratched my paint.  I have not had any issues with the bushings.  

Edited by PhilB
fixed typo
Transient Senior Enthusiast

Transient

Posted
Posted
1 hour ago, Sierra in the Sand said:

Interesting comments! Does the strip actually work as intended?

Aside from the issues I had, yes.  It does as intended.

 

I'll also add that I have the Putco led blade lightbar from GM Accessories.  The gap cover did not affect it at all.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • AlVeron
      Manufactuer's Defect - Paint Failure - Cherry Red High Country 2021 Suburban

      By AlVeron · Posted

      This is NOT impact damage nor neglect. There were previous class action lawsuits because of such paint preparation st GM manufacturing plant. Not just the Cherry Red Color. This paint is applied in three processes to obtain the desired color.  The manufacturer will cover for 36 months or 36k miles only. That rust is actually corrosion because of the paint process failure. Corrosion is covered for 100,100 miles or a certain months. However their corrosion doesn't include this type. Go figure. Clearly manufacturer knew from previous paint issues. This started 3 weeks ago out of the blue.  
    • richard wysong
      Wow I'm in a pickle. (Broke down truck) and a story.

      By richard wysong · Posted

      Is it time to put a piece of tape over the CEL? 
    • davester
      2015 Silverado 3500 right rear turn indicator failure

      By davester · Posted

      consider doing electrical testing?  I would guess some power or ground wire/connection has a problem.   alldata.com has wiring diagrams, connector pinouts and diagnostic procedures you can use to find where the problem is.
    • davester
      My First Project and GMC has me stumped

      By davester · Posted

      can you tell if the reader is actually trying to get codes, and the pcm is reporting none, or is your reader just silently failing because it's not communicating with the pcm?
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Any joy with this truck seems to be short-lived.   The CEL for P0172 ("bank 1" too rich) is now "intermittent".   I'm not sure where to check, or re-check, and my energy to keep chasing problems with junk is wearing thin. The P0172 seems to set as I'm coming to a stop, completely off the throttle, when fully warm. At least, that's what it's done the 3? times it's set.   Everything appears normal on the scanner EXCEPT long term fuel trim. There's only one bank on this vehicle because it's an OBD 1.5 with only one upstream O2 sensor. At idle, it's around -16.4% and will dip to -18% occasionally at idle or off-throttle. LTFT approaches 0 when throttle is held at 2500rpm. Short term appears normal, much closer to zero all the time. The LTFT tells me the engine is running rich at idle but compensating at higher load. But, why?   The EVAP purge valve doesn't appear to be leaking/sucking fuel vapor continuously. Is it sticking just as I come to a stop and the engine is choking on fuel vapor and sets the P0172? But that doesn't explain the persistently negative LTFT. Disconnecting the purge valve doesn't seem to make any difference.   I suppose that leaves another dang issue with the fuel injector. A leaking fuel pressure regulator, a new leak in the spider, or a leaking fuel injector/poppet valve I didn't see, or a small crack in one of the spider legs.   The vacuum line leading to the fuel pressure regulator doesn't have raw fuel in it. It doesn't even smell like fuel when it's pulled off, not until you suck air through it, then you can tell it leads to a fuel component. I'd consider that normal? Nothing is signaling this is a FPR issue from the outside, at least.   The oil smells like fuel but it's not building volume. I've noticed most oil in most engines smells like fuel to some degree so it's hard to say if the smell is an issue or not. Or if the engine just still smells like fuel because the crankcase was full of it a few hundred miles ago. But it's been changed twice since that original issue of the leaking fuel line dumping fuel into the intake.   Patience is running very thin. Every win seems to be accompanied by two steps backwards, or another issue that leads to removing at least the top half of the intake manifold. Enough! LOL

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...