Jump to content

Interior lights not working properly

Shade Tree Mechanic
 Share

Recommended Posts

Shade Tree Mechanic New Member

Shade Tree Mechanic

Posted
Posted

I have recently acquired a single cab 97 K1500. In my endeavor to get the power mirrors working, I have ran into a cascade of issues. Starting out, I found the fuse missing for the power mirrors. I replaced the fuse and the mirrors work now. Of course, the fuse controls interior lights as well. Shut the doors to celebrate my victory and noticed the interior lights still on. My only guess is the fuse was pulled to keep them off. Checked headlamp switch dimmer, not the cause. Moved to door ajar switches. Just went ahead and replaced them considering I destroyed them getting em out. No change. Thought I would try the dome override on the headlamp switch. It didn’t work. This led me to replace the headlamp switch. Now the override switch works and turns interior lights off when it’s pushed. Here’s where it gets gray. With the truck running, I shut the doors and the interior lights go out as intended. Open door and they come on. All is well and operating properly. Thought “hmm must of worked itself out” and turned the truck off and shut the doors to go inside. Well, well, the lights were still on. So, now my current situation is, interior lights operate properly with truck running and operate improperly when truck is off. Could this be an ignition switch problem considering the interior lamps work properly while the ignition is in the on position and not when it’s in the off position? 

Shade Tree Mechanic New Member

Shade Tree Mechanic

Posted
  • Author
Posted
12 hours ago, richard wysong said:

could be the timer/relay, in the electric panel above your left foot

What is the function of this timer relay? Is it kind of a “truck off, shut doors, light turns off after 30 or so seconds” kind of thing? 

Shade Tree Mechanic New Member

Shade Tree Mechanic

Posted
  • Author
Posted

Well, patience IS a virtue. I had no idea about a timer relay. After waiting patiently after shutting doors while truck was off after roughly 20-30 seconds, the interior lights went off. Thank you Richard for the help! So glad you pointed this out before I threw another part (ignition switch) at it! Now to go put the column shroud back on. 😄

richard wysong Senior Enthusiast

richard wysong

Posted
Posted

glad I could help, Thanks for posting the results, too often we never hear back on what the problems cure is

JustRangerThings Enthusiast

JustRangerThings

Posted
Posted
On 4/26/2022 at 10:45 AM, richard wysong said:

could be the timer/relay, in the electric panel above your left foot

I didnt know these trucks had timer relays. Which one is it? I'd like to add it to my truck, mine just shut off instantly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.3k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,716
    Total Members
    8,960
    Most Online
    BDS my HD
    Newest Member
    BDS my HD
    Joined

  • Who's Online   4 Members, 1 Anonymous, 748 Guests (See full list)

  • Latest Articles

  • Posts

    • BDS my HD
      Brand new to this forum. Questions about re-gearing my 26’ HD

      By BDS my HD · Posted

      Hello hello looking forward to expanding my knowledge of the 2026 2500 HD that I just bought.   Truck has 3500 miles on it four-wheel-drive crew cab and I’m about to put a 6 1/2 inch BDS lift on it 18 x 10 -25 offset with 37’s   Already have the wheels and tires just waiting on the lift install in about three weeks   Question what surprises am I not gonna be happy with?  I’m not new to lifted trucks so I know that acceleration towing gas mileage all that is affected..   Question is those of you that have this truck this powertrain with a 10 speed Allison and have done the mods that I’m doing,,, how bad is it? Is that Allison constantly gonna be hunting for the right gear to go into? And what about towing, acceleration, fuel consumption as mentioned?    Lastly how come I can’t find any ring pinion gear set up for these axles and when could I expect to see them?   I apologize if there’s any typos I’m doing speech to text on my iPhone.    
    • linc45bn
      2013 2500HD 6.0L intermittent no crank no start

      By linc45bn · Posted

      I've got a 2013 2500 6.0L Flexfuel. Drove the truck earlier today with no issues. Went to run an errand tonight and noticed key fob wouldn't work. Figured battery was dead, so replaced fob batter. Still wasn't working. Grabbed my other set of keys with the other fob and that one wasn't working either. So I manually unlock truck and insert key. Interior lights come on, dashboard lights up, turn key and truck starts. Turn truck off, like a moron, and try starting again. This time no crank, no click, no nothing. Lights still come on and dash lights up, but now I'm getting a service 4wheel drive, service tire monitor, etc. Check voltage on battery and Im showing 12.2v. Throw my battery charger on it and give it 15 mins and try starting again. But still no crank no start. Decide maybe its a bad battery, run to autozone grab a new one and put it in. Same issue. Disconnect battery and let it sit for 15 mins. Try again and still nothing. I had managed to roll the windows down earlier as its a humid night, but now I can't get them to roll up. Power locks are also not working now. Then randomly I try the key again, and it fires right up. Immediately I roll up the windows as we have nothing but rain forecast this week. I shut it back off wait 30 seconds and start up again. Worked a 2nd time. So turn it off, start putting things back together. Try one more time, and back to no crank no start. And now the car alarm starts going off. Had to disconnect battery and leave it that way for the night as I don't think my neighbors would appreciate my alarm going off again tonight. Any thoughts or help would be appreciated. 
    • Grumpy Bear
      first oil change - 2026 2500HD gas

      By Grumpy Bear · Posted

      No one will care for you like you care for you. Do what you can for as long as you can. IMHO of course. 
    • Grumpy Bear
      Oil Consumption

      By Grumpy Bear · Posted

      How about them NICKS!!! 
    • Peoplemvr
      GMC 1500 Illuminated Front Grill Emblem REPLACEMENT.

      By Peoplemvr · Posted

      Hi there.  Long time lurker, first post.    i have read the previous posts regarding the water ingress problem with this emblem.  I bought my 1500 SLT the  summer of 2025 new and after reading the MANY problems with these emblems failing I decided to install one anyways.  As per a YouTube video, I sealed ( or tried to) this sign with silicone sealant around the outer perimeter joint and the holes that were already somewhat sealed on the rear plate of the emblem.  And installed the connector assembly using dielectric grease on the connectors. The installation looked great and worked well for about 4 months……then FAILURE.  Grrrrrr…… I live in the great white north and wash my truck weekly in an automatic car wash  to keep the salt off.  Let me tell you that removing the old, failed emblem is a whole different animal than removing the OEM individual letters without removing the grill assembly. Mainly because the illuminated logo is built differently than the original letters which  you can remove the red surface lettering with a knife or some kind of blade which gives access to the tabs which hold the logo onto the grill. So I had to essentially destroyed the old emblem to remove it. Doing so killed my chance of doing somekind of autopsy on the failed , old logo.  But there was plenty of water inside when I ripped it apart.  Prior to installing the new assembly I tried it with the old harness and it works fine.   Does anyone have any insight as to where the water is getting into this emblem? I intend to seal the new logo with slow curing epoxy this time around using a syringe.  I think this newer emblem may be an updated unit which I hope GM got the vendor to fix. It has an October 2025 date on it.    If this one  fails,  I am just going to revert back to the non-illuminated letters….AFTER PULLING THE GRILL.    Any thoughts on sealing with epoxy would be appreciated. Thx!   Doug  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...