Jump to content

2027 3.0l - ordered

Jus Cruisin
 Share

Recommended Posts

Jus Cruisin Enthusiast

Jus Cruisin

Posted
Posted

Figured I'd at least get this section going. I'll be trading a 2025 GMC Sierra 1500 3.0l in on a GMC Yukon with the 3.0l Duramax. 

  • Like 1
Atlas Senior Enthusiast

Atlas

Posted
Posted

Nice!

 

What made you want to trade up your '25? with the 3.0 for a new one? (As I look suspiciously at mine...)

Jus Cruisin Enthusiast

Jus Cruisin

Posted
  • Author
Posted
12 hours ago, Atlas said:

Nice!

 

What made you want to trade up your '25? with the 3.0 for a new one? (As I look suspiciously at mine...)

A couple of reasons. The Yukon I ordered will have the air suspension that will have an entry/exit setting (lowers) to help my wife. The other? I did have some warranty issues with the Sierra that ticked me off but it's moving 2 model years which is normal for me. 

Jus Cruisin Enthusiast

Jus Cruisin

Posted
  • Author
Posted (edited)
6 hours ago, JimCost2014 said:

There are no "new model" for the SUV's in 2027, correct?

As far as I know, it's a carry over. Not sure why this forum started this section. I just noticed it yesterday but it might have been here a while. 

 

Maybe they just because there are new gassers (which the Yukon isn't getting) they decided to give the 3.0l it's own section. 

Edited by Jus Cruisin
  • Like 1
Atlas Senior Enthusiast

Atlas

Posted
Posted

I think this subforum was created for the new generation pickup trucks (2027-) with the 3.0 but I don't think it's a big deal either way. There are probably 2027 model-year specific changes for the SUV's too.

 

I was just curious if you had issues with your 2025 3.0. I'm still under 10k miles on mine and fingers crossed I don't have thrust bearing issues. I'm guessing not, since you're willing to buy another one! It's a good engine minus one or two manufacturing whoopsies.

  • Like 1
JimCost2014 Senior Enthusiast

JimCost2014

Posted
Posted
5 hours ago, Jus Cruisin said:

As far as I know, it's a carry over. Not sure why this forum started this section. I just noticed it yesterday but it might have been here a while. 

 

Maybe they just because there are new gassers (which the Yukon isn't getting) they decided to give the 3.0l it's own section. 

Kind of off topic, wife drives a 2023 Yukon Denali with the 3.0, been a great rig so far, incredible fuel economy for a truck that big and heavy. Coming up on 50000 trouble free miles.

Jus Cruisin Enthusiast

Jus Cruisin

Posted
  • Author
Posted
5 hours ago, Atlas said:

I think this subforum was created for the new generation pickup trucks (2027-) with the 3.0 but I don't think it's a big deal either way. There are probably 2027 model-year specific changes for the SUV's too.

 

I was just curious if you had issues with your 2025 3.0. I'm still under 10k miles on mine and fingers crossed I don't have thrust bearing issues. I'm guessing not, since you're willing to buy another one! It's a good engine minus one or two manufacturing whoopsies.

I had a new engine installed with under 5,000 miles. It shut off coming around a residential street corner and wouldn't restart. Dealer indicated it seized. New one has been fine since with 10,000 miles on the replaced engine. Annoying but I was given a loaner for the 5 weeks it was down. I won't go with the 6.2l gasser so it's 3.0l again. I love the economy and it tows my enclosed car trailer just fine. 

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • newdude
      Drive Cycle

      By newdude · Posted

      Conditions for Meeting a Cold Start   The ignition voltage is between 10 and 15 V. The barometric pressure (BARO) is more than 75 kPa. The engine coolant temperature (ECT) at start-up is less than 42°C (108°F). The intake air temperature (IAT) is between 2–32°C (36–90°F). The engine is OFF for greater than 6 hours or the following conditions must be met: The start-up IAT minus start-up ECT are within 12°C (22°F). The start-up ECT minus start-up IAT are within 50°C (90°F). Fuel level is between 25 and 75 %.   Circuit/System Verification Verify that all I/M System Status indicators report YES, and that no I/M Test DTCs are present.If any I/M Test DTCs are set Refer to Diagnostic Trouble Code (DTC) List - Vehicle. If no I/M Test DTCs are set All OK. Inspection/Maintenance (I/M) System Set Procedure   Warning: Refer to Road Test Warning. Note: Do NOT touch the accelerator pedal until told to do so. A change in TP Sensor angle or an increase in engine speed may invalidate this portion of the test.   Note: An I/M Test DTC will not be stored or erased from the ECU except at the end of trip processing, which occurs 5 s after ignition OFF.   Ensure that the vehicle meets the conditions for a cold start listed above. If the EVAP I/M System Status indicator displays NO, perform the EVAP Service bay test if applicable. Turn OFF all of the accessories; HVAC system, other electrical loads, including aftermarket/add-on equipment, etc., and open the hood.   Set the vehicle parking brake and ensure the vehicle is in park for automatic transmission or neutral for manual transmission.   Start and idle the engine for 2 min.   Close the hood, release the parking brake and Accelerate at part throttle to 72–80 km/h (45–50 mph) with this speed maintained until the engine reaches operating temperature, 8–10 min.   Continue operation under these conditions for an additional 6 min.   Accelerate at part throttle to 90 km/h (55 mph) with this speed maintained for 2 min.   Release the accelerator pedal for at least 10 s. This will allow the vehicle to enter the decel fuel cut off.   Safely stop the vehicle, with the engine in drive for automatic or neutral with the clutch pedal depressed and parking brake applied for manual. Allow the vehicle to idle for 2 min.   Shift the vehicle to park for automatic and neutral for manual. Turn OFF the ignition and exit the vehicle. Do NOT disturb the vehicle for 45 min.   Observe the Inspection/Maintenance (I/M) System Status with a scan tool. All of the I/M System Status indicators should display YES.   If the EVAP I/M System Status indicator displays NO, turn OFF the ignition, ensure that the vehicle meets the conditions for a cold start, and repeat steps 6-11 three more times, or until the EVAP I/M System Status indicator transitions to YES. If the indicator continues to display NO, refer to the Inspection/Maintenance (I/M) System DTC Table to identify the DTCs that did not run.   If any of the I/M System Status indicators display NO, refer to the Inspection/Maintenance (I/M) System DTC Table for the indicator which did not display YES. The I/M System DTC Table identifies the DTCs associated with each I/M System Status Indicator.   Observe the I/M Test DTC information with a scan tool. Verify there are no I/M Test DTCs present. If an I/M Test DTC is set, diagnose the DTC using the Diagnostic Trouble Code (DTC) List - Vehicle and refer to Inspection/Maintenance System Check.   Observe the engine DTC information with a scan tool. Verify no DTCs are present. If a DTC is set, diagnose using the Diagnostic Trouble Code (DTC) List - Vehicle. After repairs, perform the Inspection/Maintenance Complete System Set Procedure to verify no further DTCs are set.       Looks like one procedure to me.  Repeated as necessary.
    • calgator73
      6.2L L87 Powertrain Engine Noise (Lifter Failure) Question

      By calgator73 · Posted

      My 2020 AT4 6.2 has had the valve spring issue addressed at ~200 miles, front cover/pump replaced at 18k, water pump at 34k and idler pully at 65k.  I would agree with ditching by 100k unless you elect to go with upgraded hardware...say built 10l80 and an lt4 or l8p swap.
    • todd wollemann
      Hot fuel module

      By todd wollemann · Posted

      I also need one of your modules for my 1993 chevy c2500 7.4 Thanks! My email is [email protected]
    • C/K Man
      2027 Chevrolet Silverado: Official Discussion

      By C/K Man · Posted

      Chevy needs to do a black regular cab short box SS model with the new 6.6L.  400SS.
    • davester
      Drive Cycle

      By davester · Posted

      You might find the drive cycle you need somewhere on charm.li (website), otherwise I suggest a subscription to alldata.com to get them for your truck.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...