Jump to content

2014+ Leveling Kits

bcazier

By bcazier
in Modifications & Accessories

 Share

Recommended Posts

Big Whiskey Senior Enthusiast

Big Whiskey

Posted
Posted

Hey guys what's the likelihood for the rear axle to shift when installing new lift blocks? And if it happens, how do I fix it? 4 wheel alignment? Unless I'm seeing things it appears my passenger rear is shifted forward about 1.5" compared to the driver side rear after I put in new 2" blocks. At least that's what the tape measure is showing me. Thanks.

 

There are holes in the block and dowels where they sit.. If the installer didn't line them up correctly it's possible. They only go on one way. You would have to loosen the u bolts and position the block in correctly

This. To the OP, can you tell if the blocks and u-bolts look the same on both sides? The blocks are probably tapered a little to adjust the pinion angle. The shorter end should be pointing towards the front of the truck. You should have the same amount of u-bolt coverage on both sides. And, the blocks have a centering pin that will make sure they're sitting on the exact same place on the axle. If any of these things are off, then your axle may have shifted.

  • Like 1
  • Replies 7.7k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Saleenpowr
Saleenpowr

So i put my RC 2" level kit and Toyo 295/55/20's on this weekend. Install was simple, just like on my 2011. It definitely helps to have an extra set of hands when wedging that spacer in there. 295/

Saleenpowr
Saleenpowr

Thanks. Here is one more from yesterday. Considering we're getting 8-10 inches of rain the next two days, I won't be taking any better pics soon.  

FH212
FH212

Mine is finally done! After months of research I went with the RC 2.5" level kit front only, stock rear block. 20"x9" Fuel Nutz w/ +1 offset, 33x12.50x20 Toyo M/T tires. No rubbing, No trimming, yet a

Posted Images

cato Enthusiast

cato

Posted
Posted (edited)

 

This. To the OP, can you tell if the blocks and u-bolts look the same on both sides? The blocks are probably tapered a little to adjust the pinion angle. The shorter end should be pointing towards the front of the truck. You should have the same amount of u-bolt coverage on both sides. And, the blocks have a centering pin that will make sure they're sitting on the exact same place on the axle. If any of these things are off, then your axle may have shifted.

 

Thank you for the reply.

 

We did make sure the taper angle was larger to the rear and all the pins line up. The one thing we didn't do when installing the blocks was to disconnect the lower shock bolts. Not sure if that really matters or not. But unless the actual truck bed is off square with the frame, the passenger rear tire sits more fwd than the driver rear tire almost 1.5". Thrust angle seems off a bit. Anyone know if this is corrected with 4 wheel alignments? Seems to ride very nice still.

 

BTW new BFG's going on today! Finally!

Edited by cato
Big Whiskey Senior Enthusiast

Big Whiskey

Posted
Posted

 

Thank you for the reply.

 

We did make sure the taper angle was larger to the rear and all the pins line up. The one thing we didn't do when installing the blocks was to disconnect the lower shock bolts. Not sure if that really matters or not. But unless the actual truck bed is off square with the frame, the passenger rear tire sits more fwd than the driver rear tire almost 1.5". Thrust angle seems off a bit. Anyone know if this is corrected with 4 wheel alignments? Seems to ride very nice still.

 

BTW new BFG's going on today! Finally!

Well, if it none of those things...then I'm out of ideas. May have to take it to an alignment shop. I wouldn't think the bed would be off that much. Have you measured from the center of the front wheel to the center of the back wheel on both sides?

cato Enthusiast

cato

Posted
Posted

Well, if it none of those things...then I'm out of ideas. May have to take it to an alignment shop. I wouldn't think the bed would be off that much. Have you measured from the center of the front wheel to the center of the back wheel on both sides?

Haven't measured yet. I will tomorrow. Alignment report shows the thrust angle is off some. I'll post it tomorrow with some pics of new set up. Thanks guys.

cato Enthusiast

cato

Posted
Posted

Ok so here's before n after pics.

 

Before: Stock height front = 36.5", Rear = 38.25"

 

IMG_3528_zpsga9mjqum.jpg

 

After: 2" RC level front = 38.75", 2" Ready Lift blocks rear = 40.75"

& BFG AT KO2's (275/70x18). Truck now sits approx 3.5" higher. I like it.

 

IMG_3850_zpsashrugyi.jpg

IMG_3852_zpsj6xxtwb8.jpg

 

As I mentioned before, this is my winter setup. Next spring will come 5" RCX lift and new 20" wheels n tires.

  • Like 2
cato Enthusiast

cato

Posted
Posted (edited)

Keep us posted! Good luck!

 

Ok so I measured front center hub to rear center hub. Here's what I got.

 

Passenger side = 143"

Driver side = 144"

 

Definitely a difference. And here's a copy of my 4 wheel alignment report.

 

IMG_3849_zps9j5wcxjs.jpg

 

So now what? Seems off by a degree?

Edited by cato
Ethan Hokanson Enthusiast

Ethan Hokanson

Posted
Posted

im thinking about putting on toyo mt's 275/65/r20 with a 2inch rough country leveling kit. Went to my local dealer and they said it would fit with no scrubbing. id like to know what you guys think and your opinions on this. i want the biggest tire i can run, with no scrubbing or needing to cut anything out. im just curious because some say they will and some say they dont. if this size is to big then what size do yall recommend. like i said biggest tire with no scrubbing.

  • Like This
  • Quote
  • MultiQuote
  • Edit
Ethan Hokanson Enthusiast

Ethan Hokanson

Posted
Posted

Got the level lift finished

Did they srub or rub anything at all im thinking about running the same size tires on my truck. Ive got a 2inch level on mine and was told these size tires wouldnt scrub. Have you had any issues?

Shtoy Enthusiast

Shtoy

Posted
Posted

Did they srub or rub anything at all im thinking about running the same size tires on my truck. Ive got a 2inch level on mine and was told these size tires wouldnt scrub. Have you had any issues?

 

Hey bud! I had a little bit of rub at full lock, so I had to zip tie the felt back in the wheel well and now I have zero issues with rub. You will not be disappointed!

Big Whiskey Senior Enthusiast

Big Whiskey

Posted
Posted

 

Ok so I measured front center hub to rear center hub. Here's what I got.

 

Passenger side = 143"

Driver side = 144"

 

Definitely a difference. And here's a copy of my 4 wheel alignment report.

 

 

So now what? Seems off by a degree?

I'm stumped dude. :dunno: Did the alignment shop offer any advice? At least your truck looks really good, lol

  • Like 1
Bandit33x Enthusiast

Bandit33x

Posted
Posted

For those of you with the RC 2.5" leveling kit, did you have any issues getting the camber back to where it is supposed to be? My shop guy is worried about getting the camber back to 0 (or whatever it is supposed to be) after the 2.5" Rough Country. I'm not sure if 0 is the right number, and I'm not really familiar with where everything is supposed to be. He's suggesting the Fabtech 2" and prefers Fabtech since he believes it is a better product. I really like the look of the 2.5", but am wondering if I should take his advice, even though lots of people in this thread don't seem to have any problems with there 2.5" kit.

Bobbylowe5051 Enthusiast

Bobbylowe5051

Posted
Posted

Supreme Suspension 3" leveling kit

Mayhem Patriots wheels wrapped in 305/55r20

 

They barely rub on the fender liner when in reverse - but not even enough to warrant the "zip tie trick" just yet.

 

Front fender measurement 40.25"

 

No rear measurement, but I'll get it after adding 2" block

 

 

post-148697-0-54730800-1443484490_thumb.jpg

 

 

post-148697-0-54730800-1443484490_thumb.jpg

post-148697-0-54730800-1443484490_thumb.jpg

post-148697-0-54730800-1443484490_thumb.jpg

Dropsix Enthusiast

Dropsix

Posted
Posted

Here's what I'm thinking. I think I'll be happy with that, no more mods after. Going to Aim for 3/4" lift in the back and 1.25" up front.

 

Maybe a tune next year.

 

EFC_8367-2_zpsheye2wls.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,949
    Total Members
    8,960
    Most Online
    Gkistler
    Newest Member
    Gkistler
    Joined

  • Who's Online   3 Members, 0 Anonymous, 881 Guests (See full list)

  • Latest Articles

  • Posts

    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • PunchT37
      Parking Brake - Automatic Engagement Questions

      By PunchT37 · Posted

      I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...